Yes, you can use the Universal MightyMounts for Yakima Roof Mounted Accessories # Y03590 with your 1-1/2 inch diameter round bars, as they are compatible with both aero, square, and round crossbars. I have reached out to Yakima before regarding the use of these on round bars and they said that they will fit, but it is possible the fit wouldn't be the best and may roll a bit, but they are capable of working with round bars.
I have added a link below to the instructions and a video review... view full answer...
We do offer a replacement shroud for your Coleman Mach 3 model 7333B8876 air conditioner; with the correct replacement being from MaxxAir:
- MaxxAir Replacement RV Air Conditioner Cover - Coleman-Mach / RVP # MA8335A5261
This unit is designed for Coleman-Mach air conditioners, measures 37 inches long, 26 inches wide, 13-1/2 inches tall, and is the exact shroud you need to protect your Coleman AC. view full answer...
Yes you could use the Curt Cargo Carrier part # C18113 in the front hitch of basically any vehicle including a Ford Econoline like you mentioned. view full answer...
Thanks for the picture! If your bumper is stamped with a 5,000 lbs towing capacity you should be good to go. I would recommend double checking with your owner's manual to confirm. If you do decide to get a hitch I recommend the Curt Trailer Hitch item # 14055. With an aftermarket hitch you will have more capacity to haul heavier trailer's and the ability to use a weight distribution system to control sway. You won't be able to use one on a bumper pull.
Since your Coachman camper weighs... view full answer...
The Westin Fey Surestep Rear Bumper # 61001 you referenced is only designed to fit the following models:
1983-1993 Dodge Ram 50
1988-1995 Isuzu Pickup
1983-1996 Mitsubishi Mighty Max
1980-1994 Toyota Pickup
For a 2003 Ford E-250 Van you would instead need the Westin Fey Diamondstep Rear Bumper # 20107, which will come with a custom-fit mounting bracket. view full answer...
There isn't a custom fit hitch for your 2007 Ford Collins E450, so you'll need a weld-on hitch, with the right one depending on the drop you need, as well as your frame width. If the width of your frame is 44 inches or less (from outside to outside), you can use one of the following:
- 3" Drop: Class V Universal Weld-on Receiver Hitch and Brackets # 15901
- 9" Drop: Class V Universal Weld-on Receiver Hitch and Brackets # C47CR
For the drop, what you'll want to do is measure straight... view full answer...
I'm guessing whoever it was asked for your VIN to try to determine if you have the standard E-350 or the Super Duty which is the extended model. It looks like the standard, or Econoline/Club Wagon, uses the square plug you have seen like what is found on the K-Source Custom Extendable Towing Mirror # KS61200F and # KS61199F.
As far as I can tell, the Super Duty uses the round plug which is what Dorman shows for that model. It may be a hassle, but honestly since you plan on replacing them... view full answer...
The hitches available for your 2006 Ford E350 shuttle bus are going to be weld on hitches. I recommend the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" Item # 41990-07. This hitch is designed for heavy duty and commercial vehicles with a 1600lb max tongue weight and a 16000lb gross towing capacity. view full answer...
No but you can use a universal hitch as there are no custom fits. For a Class V hitch that you can bolt or weld onto your frame that is 42 inches from outside to outside you can use one from Draw-Tite:
- Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07
Or for a weld-on only you can use the Class V Universal Weld-on Receiver Hitch and Brackets with 3" Drop # 15901. view full answer...
They do not offer a specific wiring harness for a Massimo Warrior UTV however; you can add a universal wiring harness and splice the wires into your taillight wires. I recommend the Curt Vehicle Wiring Harness with 4-Pole Flat Trailer Connector - 60" Wire Lead Item # C58044. view full answer...
The Edge InSight # EP84030 is a comprehensive gauge display that will work on any vehicle with an OBDII port which does included your 2003 Ford E-450 van. Please note this is not a programmer so it cannot change the tuning of the motor or anything. It can read and clear fault codes. view full answer...
With your 2014 Ford E-450 box truck you will need to select from either the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver with 7" Brackets # 41990-07 or with 16" Brackets # 41990-16. These receivers can be either bolted or welded to the frame. You need to use this style of receiver as since your E-450 was built as just a chassis and several different aftermarket manufactures did the up fit to add boxes or turn them into RV's there is not one particular hitch which will bolt... view full answer...
The Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class C Motor Homes # RM-RBK24-RSSC is the correct fit for your 2006 Ford E-350 with V10. The class B versus class C aspect doesn't change the fit. The frame and motor confirm this is the correct fit for your 2006 Pleasureway Excel TS motorhome.
I've attached the installation details to assist as well as a review video and video of a similar installation. view full answer...
We have not had the chance to install trailer hitch # 41945 on a vehicle so we do not have a video or pictures. But there is a diagram in the instructions, linked for you, that shows the hitch installed in the proper position. The pin hole is nearly flush with the rear bumper.
If you plan on doing some towing, the most popular ball mount for this hitch is # BWBMHD30010 and you can use pin and clip # PC3. For a 2 inch ball use # A-90 and for a 2-5/16 inch ball use # 19286. view full answer...
The install and removal of the step portion of the GlowSteps part # TLA7802 is pretty easy and does not require the use of any tools. Basically you just pull out cotter pin and then slide the pin out and you can remove the steps from the bracket. No tools required at all.
In the attached picture you can see how someone replaced the pin with a lock. view full answer...
For your vehicle the I recommend the Roadmaster Front Anti-Sway Bar Item # RM-1139-115 and the Roadmaster Rear Anti-Sway Bar Item # 1139-178. I verified your VIN number with Roadmaster to ensure these were a confirmed fit. view full answer...
Yes, I confirmed with Saris that the Saris Bones 2 Bike Rack - Trunk Mount - Adjustable Arms # SA805BL will fit your 2007 Ford E350 cargo van with back barn style doors. However, you will not be able to open the back doors with the rack attached. view full answer...
For motorhomes with a longer chassis you won't be able to install a standard hitch like the one that bolts to your 2013 Ford E-350 chassis. You'll have to install a universal-type hitch on your chassis like the Curt # 13703 which can fit chassis from 22" to 72" Wide.
Since this isn't a custom hitch you'll need to make sure this is compatible with your frame, or have a shop help you confirm this as well prior to installing it.
I'm also linking our selection of universal-type hitches for... view full answer...
I recommend the Draw-Tite Max Frame, part # 75703 for your 1997 Ford Club Wagon. I called my contact at Draw-Tite and they confirmed the # 75703 as a fit.
If you plan on doing some towing you might be interested in etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with clip, and a storage bag.
If the ball mount kit does not include... view full answer...
Go To Results