Yes, you should still be able to use the Tekonsha Wiring Harness, # 119250KIT, with your 2009 VW Tiguan. I have included a link to the installation details for you. you will wire your Tiguan using the 3-wire directions. view full answer...
The etrailer Trailer Hitch Receiver part # e43ZR which is a fit for a 2019 Volkswagen Tiguan will still allow for use of the hands free liftgate feature. That said, you will be limited to areas beside the receiver tube. view full answer...
I added a cut out from the instructions that shows exactly what type of fascia trimming is required to install the EcoHitch Stealth Trailer Hitch Receiver # 306-X7313 on your 2016 VW Tiguan.
Trimming this will allow you to access the frame's weld nuts so you can install the hitch. view full answer...
Yes, you can absolutely run the hot lead of the Wiring Harness with 4-Pole Flat Trailer Connector # 118675 through the cabin of your 2017 VW Tiguan. You are certainly not alone in not having access to a lift and feeling that going underneath the vehicle can be a pain, so you can route it through your cabin, using Trim Pad Remover # ALL648544 to loosen the trim.
In fact, we have a help article about running a hot lead, and I added the section about routing the wire through your vehicle;... view full answer...
In order to install trailer wiring harness # 119250KIT on a 2011 Volkswagen Tiguan you will need to gain access to the wiring behind each of the tail lights. You will most likely need to remove the tail light assemblies be removing the fasteners that hold them on. This will give you access to the wiring that plugs into the tail lights so that you can test them to determine the functions of the wires needed for installation. I have included a link to the instructions for reference.
Since... view full answer...
I wasn't able to locate any instructions for the VW 5NN055203A wiring harness you purchased. I'd recommend taking the simpler and considerably more inexpensive route by using an aftermarket wiring harness like
# C56403 which plugs inline at the connection between the vehicle's taillight wiring harness and the taillight assemblies. The harness gets is switching information from these connections but draws its power for the trailer lights directly from the vehicle battery via the fused connection... view full answer...
Since your 2016 Volkswagen Tiguan R-Line does not have the removable fascia piece there will be some trimming required to install the etrailer trailer hitch # e98906. I have included a picture that shows where and how much to trim.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes a 1-7/8 inch ball, 2 inch ball, hitch pin with... view full answer...
The only tools needed to install the Curt Trailer Hitch Receiver # C13381 on your 2020 VW Tiguan are a ratchet, torque wrench, 13mm & 16mm sockets, as well as safety glasses. The installation of this hitch is as simple as possible and literally only requires you to remove bolts, lift the hitch up and reinstall the bolts.
I have added a link to the installation instructions as well as a link to a video install for you to check out as well. view full answer...
According to Tekonsha, the 2012 Volkswagen Tiguan needs to be wired using the BM-1 code in the instructions (linked for reference).
This would mean that the brake lights, turn signals, and tail lights are combined onto 1 circuit for each side of the vehicle. So you will attach the yellow wire for the converter to the left side wire on the vehicle that carries those 3 functions, the green wire attaches to the combine 3 function wire on the right side. The red and brown wires will ground... view full answer...
While we do have a photo of the etrailer Hitch # e43ZR on a Volkswagen Tiguan, we only have that photo of a 2018 model. We unfortunately do not have a photo specifically on a 2022 model. I went ahead and attached 2 photos of the hitch installed to this answer.
As far as cutting, I am pleased to say that the hitch does not require any cutting whatsoever on your 2022 model. The installation is super easy and can be done in about 30 minutes.
I also attached a photo of the full step-by-step... view full answer...
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118811 should be connected directly to the vehicle battery. This protects your vehicle wiring and it make sure you don't end up with a blown fuse or short circuit. The module draws 7.5 amps per circuit for the tail lights and 5 amps per circuit for stop/turn lights.
The battery powers the module which in turn powers the trailer lights. It keeps the module and trailer from drawing power from the vehicle turn/stop... view full answer...
Adjunto el enlace a las instrucciones de instalación del arnés de cableado del vehículo T-One # 118675, así como un video de instalación. Es compatible con un Volkswagen Tiguan 2012, por lo que solo debe enchufarlo a los arneses que están detrás de las luces traseras de su vehículo. view full answer...
According to Tekonsha, the 2010 Volkswagen Tiguan needs to be wired using the BM-4 code in the instructions (linked for reference).
This would mean that the brake lights, turn signals, and tail lights are combined onto 1 circuit for each side of the vehicle. So you will attach the yellow wire for the converter to the left side wire on the vehicle that carries those 3 functions, the green wire attaches to the combine 3 function wire on the right side. The red and brown wires will ground... view full answer...
I do have a helpful video and explanation on how to remove the taillights on a 2016 Volkswagen Tiguan but we have not had the chance to do this on a 2018 yet therefore, I would not be able to provide you with exact instructions.
As you can see in the attached video, in order to remove the taillight assembly on a 2016 Volkswagen Tiguan you will need to first remove the black trim panel located beside the taillight housing in the seam where the hatch and taillight meet. You will want to... view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class II - 1-1/4" item # C12177 will fit with your 2022 Volkswagen Tiguan R-Line. This hitch receiver fits all models of the Tiguan including the R-Line Black. The new R-line Black has more trim between the bumper and muffler that will need to be cut off or removed. I have attached a couple pictures of the trim that is going to need to be cut into. The hitch receiver will still sit underneath your Tiguan's Bumper. I have also attached an installation... view full answer...
I have attached a link to the installation instructions for the Tekonsha ZCI Circuit Protected Vehicle Wiring Harness with Install Kit, # 119250KIT.
Since this is a universal wiring kit, specific instructions for your 2013 Volkswagen Tiguan are not provided. Due to the instructions not being vehicle specific, I recommend testing the tail light wires before splicing and making your connections. view full answer...
Yes, I have attached for you an install video of the Curt Trailer Hitch Receiver part # C13133 which you can use to install the etrailer.com Trailer Hitch Receiver part # e98906. These two hitches are the same save for finish (matte vs gloss) so the install video will apply to both options. view full answer...
We currently do not have a video of the installation of the EcoHitch # 306-X7395 on a 2018 VW Tiguan but as soon as we do get one through the shop we will do a video on this. However, there are detailed instructions included with this hitch that walk you through the process.
To try to give you a simple run down, it will involve removing the bumper and fascia, as well as the steel partition behind the bumper and replacing that with the hitch. You'll bolt it on and then replace everything... view full answer...
It is possible that on your 2009 Volkswagen Tiguan you will need to follow the alternate installation instructions for the Touareg. I have included a link to an article that explains this.
That would be if you are unable to locate a proper dedicated brake light only circuit. The first place to check is above the brake pedal. Look for a brake switch with wires going in and out of it. Use a circuit tester such as # PTW2993 to probe the wires (the key may have to be in the on position).... view full answer...
The Curt # C56403 is what is referred to as a powered taillight converter. The converter box itself taps into the vehicle's taillight wiring, and converts a 3 wire system (stop lamp, right turn and left turn signal) into a 2 wire system with stop and right turn combined onto one circuit and stop and left turn combined on another.
Older taillight converters also drew the power to run the trailer taillight circuits through each individual circuit itself, but as vehicle wiring systems got... view full answer...
Go To Results