To use the Security Strap for Yakima Trunk Mounted Bike Carrier # Y02623 you will need to run the loop end of the strap around any portion of the bike rack you can fit it on and then close the roller side in the rear hatch of your vehicle. To see how this is done check out the 1:00 minute mark of the video I attached to the right. view full answer...
There is no one specific way that the power wire has to be run for trailer wiring harness # 118590 for your 2014 Chevy Impala. Running it through the interior of the vehicle takes the longest, and you may need additional wire, but it also offers the most protection. I have included a link to a help article I wrote with tips on routing the power wire. view full answer...
The Peterson # PE26UR Magnetic Tow Lights could be modified by doing some cutting and splicing to work as you describe.
You would attach the connector of the wiring harness at the front of the vehicle and run the wiring under the vehicle. Following the frame member or an existing wiring harness works best. Run the wires to the rear of the vehicle, being sure to avoid any suspension and steering components that might move or anything hot like the exhaust system. Under the vehicle at the... view full answer...
The CURT # C56188 is confirmed to fit your 2015 Chevrolet Impala, so I'm a little curious as to why you're having trouble plugging in. If you can tell me a bit more about how the plugs aren't connecting, I will be happy to look into this further. An additional converter shouldn't be necessary. The installation notes state:
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located in your rear cargo area (behind the driver and passenger side tail lights - inside... view full answer...
I would just run up to a hardware store and grab a couple bolts with a matching nut and lock washer and secure the plate with that.
You will want to use bolts with a diameter of 5/16 of an inch or smaller as that is the diameter of the mounting slot. view full answer...
I checked the online owner's manual for the 2010 Chevrolet Impala and on page 5-27 and 5-28 the preparation process to tow this car on a dolly like the Roadmaster # RM-2000-1 is outlined. Here is the complete procedure from the manual:
1. Attach the dolly to the tow vehicle following the dolly manufacturer’s instructions.
2. Drive the front wheels onto the dolly.
3. Shift the transmission to P (Park).
4. Firmly set the parking brake.
5. Use an adequate clamping device (an old tire's rubber... view full answer...
No, the manufacturer of the Draw-Tite Trailer Hitch, # 36407, for the 2010 Chevrolet Impala does not require the use of a stabilizing strap, part # 18050, for carrying a bike rack and bikes within the capacity of the hitch and vehicle. I have added a link to instructions for you to review.
For a bike rack, I would recommend the Yakima HoldUp 2 Bike Rack, # Y02445. This rack is the one most often purchased by our customers who own the Chevrolet Impala. We have a video review of this rack... view full answer...
The Coil SumoSprings Custom Helper Springs # CSS-1195R for the rear axle of your 2012 Chevrolet Impala will not affect unloaded ride-height. These helper springs will only come into effect when the rear of the vehicle is loaded down with weight. It will simply assist your suspension and help support heavy loads along with reducing body roll on turns.
There are not any products available to increase the ride-height of your Impala. It is possible that your rear suspension is simply worn-out... view full answer...
You would not want to open the trunk while a trunk mounted bike rack is installed on your 2007 Chevrolet Impala because it could cause damage to the vehicle.
If you would like to have access to your trunk without having to remove the bike rack every time, then I would recommend adding a hitch and hitch mounted bike rack. For your vehicle, I would recommend the Draw-Tite Class II Hitch, # 36407. There will be no contact between your vehicle and a hitch mounted bike rack and you will be... view full answer...
If you're struggling to get the straps loose from the 3477 Roadmaster Tow Dolly # RM-2050-1 since your 2009 Chevy Impala sits too low, you'll need to move the release down and hold it there manually while you pull down. This will loosen up the strap and then might give you enough slack to then open up the handle fully to make removing the strap easier.
Unfortunately there aren't any smaller handles that you can swap out with this to make it easier to operate in those regards. view full answer...
Based on the pictures that are on the product page (the last 2 show it the best), and the image in the upper left corner of the instructions that I have linked, the receiver will be the only part of the hitch easily visible once installed on your 2000 Chevy Impala.
If you plan to do some towing the recommended ball mount is # 36061 for use with ball # 19256 (1-7/8 inch diameter) or # 19258 (2 inch diameter). For trailer wiring, you would use # C56116. I have included a link the installation... view full answer...
Yes, our trailer hitches like the Draw Tite part # 36543 that you referenced do come with install hardware. The picture I attached shows the hardware that comes with this hitch. view full answer...
We have a great helpful article on how to route the power wire for a trailer wiring harness like the Hopkins Plug-In Simple # HM11141434 that fits your 2015 Chevrolet Impala. The article explains how to find existing wiring grommets you can use to run the harness power wire up to the battery.
I also linked a helpful article for your hitch installation. view full answer...
You can mount the fenders directly to the trailer frame through the fender skirt on the back of the fender. I would recommend using large washers if you drill through the fender skirt and attach the fender directly to the trailer frame.
If mounting directly to the trailer frame is not possible on your trailer, you will need to use brackets to attach the fenders. We have the Galvanized Steel, L-Shaped, Bolt-On Brackets, item # PF775-BKT-2, that could be used to mount these fenders, # F008543,... view full answer...
The Kat's Heaters Custom Engine Block Heater # KH11484 installs in the right front location on your 2008 Chevy Impala with a 5.3L V8 engine, as you can see by the accompanying diagram from Kat's.
I have added a link to a video review of this heater for you to check out as well. view full answer...
The Curt wiring harness # C56046 as well as the Tekonsha harness # 118417 both plug into just one side of the 2011 Chevy Impala. The main tail light wiring harness that runs from the front to the back of the vehicle is located on that side so it is possible to just tap into that harness.
The Hopkins harness # HM11141595 is just a different design. The connectors for the passengers side do not have the wiring in them to get the signals for the left side of the vehicle like the other harnesses... view full answer...
The Draw-Tite # 36538 is the trailer hitch receiver that fits your 2017 Chevrolet Impala. If you take a look at the video of the hitch being installed that I've attached, at around the 6:40 mark you'll see the optional cutting being described. It isn't required but there is some cutting that can be performed for the install.
This is the same area that needs to be trimmed for the Curt # C12115. Which is also shown in the other video around the 1:35 mark. view full answer...
The Yakima JetStream roof rack that fits your 2014 Chevy Impala includes the following parts:
50" Yakima JetStream Crossbars - # Y00428
BaseLine Towers - # Y28TR
Front BaseClip - # Y06124
Rear BaseClip - # Y06126
Lock Cores - # Y07204 (optional)
I listed which clip should be in which position above but if I hadn't told you this, you can find these fitments in the instructions or on the Yakima website.
Attached are some videos for you to check out! view full answer...
The Edge Insight CS2, part # EP84030, is not a tuner type of programmer. It can display several parameters and allows you to monitor them but you cannot tune the engine with it. It will not add horsepower, torque, or change any of the factory settings on your 2006 Chevrolet Impala. It can be used with other performance chips to track and monitor your newly tuned engine.
Some of the parameters you can monitor are listed below:
Battery Voltage
Intake Air Temperature (IAT)
Engine Oil Pressure... view full answer...
The Kat's Heaters Custom Fit Engine Block Heater # KH11811 has an internal thermostat that will turn the heater on when the coolant temperature drops below 0 degrees. So if your coolant is below 0 degrees then yes, it will turn on right away. I'm not sure what the higher temperature shutoff is but it won't stay on constantly unless that is what is needed to keep the coolant above 0 degrees. view full answer...
Go To Results