According to Rhino-Rack, the StealthBars # JA7981 fit your 2013 Ford Explorer XLT as long as you have raised factory rails on your roof. This part is a complete system that includes 2 crossbars, 4 legs, and a fit kit.
To see a product demonstration video, please click the provided link. view full answer...
The Thule Motion XT Rooftop Cargo Box # TH629907 will fit the spread of your crossbars as long as it is less than 36-7/8 inches apart. The maximum crossbar dimensions for the carrier clamps are 3-1/2 inches wide and 1-11/16 inches tall. Also, the rear hatch will fully open once the carrier is mounted. There are no additional hardware materials needed for installation. view full answer...
The correct Roadmaster Tow Defender Protective Screening to use with a Roadmaster Crossbar-Style Base Plate Kit is part # RM-4700. The correct Roadmaster Tow Defender Protective Screening to use with a Roadmaster Direct Connect-Style Base Plate Kit is part # RM-4750. view full answer...
According to my Curt representative, their # C56093 T-Connector will work just fine with your 2013 Explorer. It will not cause any interference or problems with your back-up sensors.
If you'd care to look over the installation instructions or an install video, please use the provided links. view full answer...
The Derale # D15902 isn't a vehicle specific product, but you'll want to measure to see if there's available space for the heat exchanger. The best and most efficient place to mount the heat exchanger is directly behind the grille, in front of the radiator and A/C condenser. You'll want to ensure that there's sufficient space to accommodate the 17 inch wide x 12-1/2 tall x 3/4 inch thick heat exchanger.
The sandwich adapter for the oil filter includes a 22mm x 1.5 sleeve nut, which is... view full answer...
Yes, the bars on the Malone MicroSport Trailer with J-Style Carriers for 4 Kayaks - 800 lbs, part # MPG462G2, has square crossbars, so your Malone Paddle Carrier for Roof Rack Crossbars - Clamp On - 4 Paddles, part # MPG121, will easily install to the bars.
I have included a product description link and video review links below. view full answer...
The Thule WingBar Evo Crossbars - Silver - 60" # TH711500 and Feet # TH710401 should be able to accommodate the Thule Hullavator # TH898 without an issue. To be sure, you can measure from the center of one side rail to the center of the next side rail on your roof; if this distance is 52" or less then you will have enough overhang.
Each Hullavator requires 28-1/2" of crossbar space, so you will have enough room to install two of them. Keep in mind, each Hullavator weighs about 40lbs so... view full answer...
Yes, the Thule SquareBar Evo crossbars are 100 percent compatible with the Malone MegaWing Fishing Kayak Carrier # MPG207.
The MegaWing # MPG207 will attach directly to the SquareBar crossbars with its clamping system. It even has a cut out made specifically for square crossbars, as you can see by the photo and portion of the instructions I attached. view full answer...
We do have trailer hitch receivers to fit your 2017 Ford Explorer but the Draw-Tite # 75278 will not fit. It's for several different models of GM vans.
Instead you'll want to use Draw-Tite # 76034 on your Explorer. I've linked an install video for you. If you're going to be towing a trailer you'll also need a wiring harness. I recommend the Tekonsha 4-way # 118540.
You'll also need a ball mount and hitch ball. I've attached a link of our selection of ball mounts for a 2 inch hitch... view full answer...
The MagnaFlow Ceramic Catalytic Converter part # MF49575 is a direct fit catalytic converter which means it will only fit Ford Explorers and Mercury Mountaineers from 2002 - 2004 with the 4.0L V6 engine. Therefore, the MagnaFlow Ceramic Catalytic Converter will fit six different vehicles. view full answer...
Yes, the Thule Snug Tite Hitch Lock and Anti-Rattle Device part # THSTL2 will work with the Thule Transporter Combi Hitch Mounted Enclosed Cargo Carrier part # TH665C. The weld nut inside the shank on the Thule Transporter is the same as that on the Thule bike racks. If you want to be sure that the lock cores on the cargo carrier and hitch lock are the same you can also order the Thule One-Key System Lock Cylinders part # TH450200. view full answer...
We don't have any pictures or videos we can show you to help put the Derale transmission cooler part # D13960 in your vehicle but the great thing about this kit is that since it comes with a fan you don't have to put it somewhere that gets access to air flow. If there's a tighter area that it could fit it would work fine there since it provides it's own air flow. view full answer...
Yes, the Longview Custom Towing Mirror, item # CTM2200A, will fit your 2000 Ford Explorer XLS, as long as your vehicle does not have manual mirrors or mirrors with lights in the mirror housing underneath the mirror face. view full answer...
The correct Curt Trailer Hitch Receiver for a 2018 Ford Explorer is part # C13386 which offers a direct bolt-on installation. I have attached an install photo as you requested as well. If you will be towing, don't forget get the Curt T-Connector Vehicle Wiring Harness part # C56172 which is plug-n-play and the etrailer Ball Mount Kit part # 989900.
The Curt Trailer Hitch Receiver part # 13138 is for a Ford Ranger. view full answer...
Yes the Longview Original Custom Towing Mirror Slide-On Mirrors, # CTM2200A, fit the 2001 Ford Explorer Sport Trac. I am sending you a video link that shows the installation of this product. view full answer...
I checked with Curt and the Curt Front Mount Trailer Hitch Receiver part # 31545 is listed as a fit for a 2006 Ford Explorer so you will be good to go. This is actually the only front mount trailer hitch option we have for you.
Please note fit information can change so you were right to check with us but I can confirm fit for you. view full answer...
Yes, the Rhino-Rack roof rack which consists of the Rhino-Rack Vortex Aero Crossbars # RRVA137B-2, the RLCP Leg Adapters # RRVA-FK2-2, and the RLCP Leg Kit # RRRLCP45 will fit your 2016 Ford Explorer.
This system will install on the flush rails that run front to back of your Explorer and will allow you to use the Upright Roof Bike Carrier # S64720.
I have attached some review videos for you to check out. view full answer...
The length is 4-1/4 inches for the Easy Grease Trailer Idler Hub for 2K Axles - 13" to 15" Wheels - 5 on 4-1/2 - Pre-Greased # AKIHUB-545-2-LF-2K.
We do not have a 3-1/2 inch long hub. view full answer...
Appreciate the purchase and we have exactly what you need. Since the Draw-Tite Max-Frame Trailer Hitch Receiver # 76034 for your Ford Explorer comes with a mounting tab for a bracket, all you need to mount the T-One Vehicle Wiring Harness with 7-Way # 118272 is the following:
- Mounting Bracket # PK12711U
The # PK12711U even comes with the installation hardware so you won't need anything else. view full answer...
The Tekonsha T-One Vehicle Wiring Harness # 118599 will give you a 4-way flat connector for your utility trailer to connect to your 2022 Ford Explorer. This harness uses factory style connectors so you will not have to splice into the tail light wiring on your Explorer.
The Mounting Bracket # 18144 will allow you to secure the 4-way connector on the back of your Explorer to prevent it from becoming damaged if you choose to route the connector outside the vehicle rather than running it... view full answer...