Correct Curt Trailer Hitch Receiver for a 2018 Ford Explorer
Question:
Your ad states this has NOT been confirmed to fit a 2018 Ford Explorer SUV, Can you verify? Also, would you have pictures of this installed on this particular make and model? Thank you in advance
asked by: Jackson
Expert Reply:
The correct Curt Trailer Hitch Receiver for a 2018 Ford Explorer is part # C13386 which offers a direct bolt-on installation. I have attached an install photo as you requested as well. If you will be towing, don't forget get the Curt T-Connector Vehicle Wiring Harness part # C56172 which is plug-n-play and the etrailer Ball Mount Kit part # 989900.
The Curt Trailer Hitch Receiver part # 13138 is for a Ford Ranger.
Products Referenced in This Question
etrailer Ball Mount Kit for 2" Hitches - 7,500 lbs
- Trailer Hitch Ball Mount
- Fixed Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Gloss Black
- Drop - 2 Inch
- Drop - 4 Inch
- Rise - 1 Inch
- Rise - 3 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class III
- Ball Mount Kit
- etrailer
more information >
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- CURT
more information >
Product Page this Question was Asked From
Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 400 lbs TW
- 4000 lbs GTW
- 6000 lbs WD GTW
- 2 Inch Hitch
- 600 lbs WD TW
- Visible Cross Tube
- CURT
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Article: How to Choose the Right Trailer Hitch Class
- Q&A: 2003 Ford Ranger Hitch Receiver Recommendation
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Recommended Trailer hitch Receiver For a 2008 Ford Ranger 4x4
- Article: My Trailer Hitch Doesn't Fit
- Q&A: Recommended Trailer Hitch Receiver for 2004 Ford Ranger Edge
- Q&A: Will Curt Trailer Hitch # 13138 Fit a 2002 Ford Ranger Edge Flare Side
- Q&A: Replacement Disc Brakes, Bearings, and Actuator for 2010 EZ Loader Boat Trailer
- Q&A: Fit And Compatibility Of The Kodiak 10" Rotor With The UFP DB35 Brakes
- Article: Frequently Asked Questions About Transmission Coolers
- Q&A: Can a Double-Lip Trailer Hub Seal be Used in Place of a Single Lip Seal
- Article: Which Hitches are Made in the USA
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Flat Towing Package for 2008-2011 Honda CR-V