Trailer Hitch Receiver Confirmed to Fit a 2017 Ford Explorer
Question:
Please confirm this hitch will fit 2017 Ford Explorer. HITCH #75278
asked by: Mike P
Expert Reply:
We do have trailer hitch receivers to fit your 2017 Ford Explorer but the Draw-Tite # 75278 will not fit. It's for several different models of GM vans.
Instead you'll want to use Draw-Tite # 76034 on your Explorer. I've linked an install video for you. If you're going to be towing a trailer you'll also need a wiring harness. I recommend the Tekonsha 4-way # 118540.
You'll also need a ball mount and hitch ball. I've attached a link of our selection of ball mounts for a 2 inch hitch receiver as well as an article to help you determine the correct rise or drop you may need. Once you choose a ball mount you can then choose a hitch ball to fit it.
One way to make choosing a ball mount easier is to go with an adjustable ball mount like the B&W Tow & Stow # BWTS10038B. It features the ability to be flipped under the hitch when not using it and will provide up to 5-1/2 inches of rise or 5 inches of drop.
For a pin and clip to fit you can use # PC3 or if you'd like to have a locking pin you can use # BX8858.
I've also included links to some articles on towing that you might find helpful.
Products Referenced in This Question
T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Custom Fit Vehicle Wiring
- Trailer Hitch Wiring
- No Converter
- Custom Fit
- 4 Flat
- Tekonsha
more information >
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 675 lbs TW
- 4500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Visible Cross Tube
- Draw-Tite
more information >
B&W Tow & Stow 2-Ball Mount - 2" Hitch - 5" Drop, 5-1/2" Rise - 7.5K - Black
- Trailer Hitch Ball Mount
- Adjustable Ball Mount
- 1-7/8 Inch Ball
- 2 Inch Ball
- Two Balls
- Steel Ball
- Steel Shank - Matte Black
- Drop - 5 Inch
- Rise - 5 Inch
- Fits 2 Inch Hitch
- 7500 lbs GTW
- Class IV
- B and W
more information >
Blue Ox Trailer Hitch Receiver Lock for 2" Hitches
- Trailer Hitch Lock
- Standard Pin Lock
- Keyed Unique
- Fits 2 Inch Hitch
- Flush Pin
- 2-3/4 Inch Span
- Blue Ox
more information >
Pin and Clip for 2" and 2-1/2" Hitches - 5/8" Diameter x 3-1/4" Span
- Hitch Pins and Clips
- Standard Hitch Pin
- Fits 2 Inch Hitch
- Fits 2-1/2 Inch Hitch
- 5/8 Inch Diameter
- 4 Inch Span
- Draw-Tite
more information >
Product Page this Question was Asked From
Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 5000 lbs WD GTW
- 2 Inch Hitch
- 500 lbs WD TW
- Concealed Cross Tube
- Draw-Tite
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Article: How to Choose the Right Trailer Hitch Class
- Article: Where to Position the Trailer Axle?
- Q&A: Replacement Hub Recommendation for Dexter Hub 8-250
- Q&A: Replacement LED Top Command Clearance Light With SAE-AP2-16 On Lens For 2018 Sunseeker Motorhome
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is Max Safe Tire Temperature
- Q&A: Trailer Tire Size to Replace 8.75R16.5 Tires
- Q&A: What Size Battery Is Needed for the Lippert 6-Point Ground Control
- Q&A: Could GO Power Solar Panel kit part # 34273836 Mount to Pin Box and Use SAE Port
- Q&A: Bolts and Bracket for the Tie Down Caliper to Kodiak Caliper
- Article: Must Have RV Accessories that Will Make or Break Your Trip
- Article: Choosing the Right Suspension Kit for Your Truck and Trailer
- Article: My Trailer Hitch Doesn't Fit
- Article: Wiring Trailer Lights with a 4-Way Plug (It's Easier Than You Think)