bing tracking image

Filter Questions and Answers:

reset filter

Expert Answers about Mitsubishi Endeavor


  • What Size are the Bolts for Curt Trailer Hitch, # 13113 for a 2006 Mitsubishi Endeavor
  • The bolt sizes for the Curt Trailer Hitch, # 13113, can be found in the instructions. I have included a link to the installation instructions and a video install below.
    view full answer...

  • Hitch and Wiring Install Instructions for a 2011 Mitsubishi Endeavor
  • The recommended trailer wiring harness for your 2011 Mitsubishi Endeavor is the Curt Harness part # C56039. We have not had the chance to install this harness on an Endeavor like yours so I do not have a video I can show you, but I did attach a set of the installation instructions that details how this harness installs. For a hitch for your vehicle you would want the Curt Hitch part # 13113. We do have an install video for this product that I attached for you to check out. For ball mounts...
    view full answer...

  • How to Install Trailer Wiring on a 2004 Mitsubishi Endeavor Pulling a Boat Trailer with a 5-Way
  • Yes, the fifth wire on your boat trailer is most likely a reverse lock-out solenoid for the surge brakes so that you can reverse your trailer without the brakes activating. I would recommend you install this Curt T-Connector # C56039 on your 2004 Mitsubishi Endeavor (instructions attached) and then cut the 4-way off of the harness and then wire up a Hopkins Endurance 5-Way Flat Trailer Connector # HM47900 by function to the wires that are now exposed from the # C56039 to the # HM47900....
    view full answer...

  • Parts Needed and Instructions for Installing a Brake Controller on a 2004 Mitsubishi Endeavor
  • You will need a brake controller and a brake controller installation kit, item # ETBC7, to install trailer brakes on your 2004 Mitsubishi Endeavor.I recommend the Tekonsha P2 Brake Controller, item # 90885, which is a very good seller and is also easy to use. The ETBC7 installation kit includes everything needed to install either brake controller, per the brake controller manufacturers instructions. You will also need a circuit tester, item # 3808, to find the brake circuit under the dash...
    view full answer...

  • Hitch Recommendation for a 2004 Mitsubishi Endeavor
  • The Draw Tite Hitch part # 75163 that you referenced has been confirmed to fit your 2004 Mitsubishi Endeavor and would work great for you. I attached a link to an install video that details exactly how this hitch will install on a very similar Mitsubishi Endeavor as yours. I also attached a link to the install instructions. If you follow both of these as your guide you shouldn't have any problems. I attached a link to our returns policy page for you to check out as well.
    view full answer...

  • Where Does the 4-Flat Connector from Wiring Harness # C56039 go on a 2010 Mitsubishi Endeavor
  • There may be an access point to fish the 4-flat connector under your vehicle behind the side trim panels on your 2010 Mitsubishi Endeavor, but after you install wiring harness, # C56039, the installation instructions state to store the connector in the trunk area when not in use. When you are ready to tow, you simply feed the connector over the door threshold and shut the rear hatch door. Be sure you keep the wires away from the hinge so the wires do not pinch. There should be a rubber...
    view full answer...

  • Socket Size for Installing Curt Trailer Hitch 13113 in 2008 Mitsubishi Endeavor
  • The Curt Trailer Hitch Receiver # 13113 that fits your 2008 Mitsubishi Endeavor will require you to use a torque wrench with an 18mm socket. You will need to torque all M10 fasteners to 48 lb.-ft. per the linked instructions.
    view full answer...

  • What Size Hole Is Needed For Installation Of Optronics Flush Mount 4 Inch Round Light # STL23R-24B
  • If you are using the Optronics Rubber Grommet for 4 Inch Round Trailer Tail Lights, part # A45GB, with the Optronics Sealed, 4 Inch Round LED Trailer Stop, Turn and Tail Light, Flush Mount, part # STL23R-24B, you will want to drill a 4-1/2 inch cutout. This grommet will allow you to flush mount 4 inch round lights to your trailer. If you are needing the wiring for the light I have both a right angle pigtail and a straight pigtail available. The Optronics Right Angle 3-Wire Pigtail, part...
    view full answer...

  • Bolts Provided with Hitch Will Not Fit in Nuts Welded Into Vehicle Frame
  • Your Curt # 13569 Class III hitch uses M10 x 1.25 x 35 hex bolts. Typically what happens on older vehicles or vehicles that have spent time somewhere that uses chemical de-icing agents on the pavement in cold weather is that road crud and corrosion get built up on the threads of the nuts welded up into the vehicle's frame. Once this buildup gets severe enough, it makes it difficult to get the bolts threaded in, and it seems as if the bolts are the wrong size. 99.9% of the time it's a...
    view full answer...

  • Can Roof Rack Cargo Bag, # HE3021 Be Installed Directly on the Roof of a 2004 Mitsubishi Endeavor
  • The Roof Rack Cargo Bag, Weather Resistant, # HE3021, can be placed on the roof of your Mitsubishi Endeavor, or, on the cross bars that run side to side. The soft cloth base will prevent scratches to the paint on the roof. Make sure the roof and bottom of the bag are clean and free of any debris to help prevent scratches. You will need to check the weight capacity of the roof in your owners manual to avoid exceeding the weight capacity of the roof. I have included a link to a video review...
    view full answer...

  • Brake Controller Option for Towing Camper with Several Different Vehicles
  • For the most part, a brake controller shouldn't be installed where its controls aren't in reach of the driver or where it's exposed to the elements. However, we do have an option that's perfect for what you're wanting to do. The Curt Echo # C51180 installs at the connection between the vehicle's 7-way and the trailer's trailer connector. Each vehicle will need a functional 7-way trailer connector with an active 12-volt feed. The controller uses your iOS or Android-powered smart phone as...
    view full answer...

  • Where is the Trailer Wiring Connection Point for a 2007 Mitsubishi Endeavor
  • The connection point for the Curt Wiring Harness, # C56039, on a 2007 Mitsubishi Endeavor is located under a floor panel adjacent to the spare tire compartment. What you will do is take off the floor hatch above the spare tire. You will then need to temporarily remove all floor coverings, 10 mm storage tray bolts and storage trays, exposing the spare tire compartment. Remove drivers side and center foam cargo trays to locate tow plug housing under drivers side foam tray. I have included...
    view full answer...

  • Installing Hopkins Wireless Backup Camera HM50002 in 2005 Mitsubishi Endeavor
  • The Hopkins Smart Hitch Backup Camera # HM50002 will plug in on any vehicle that has a 7-way trailer socket with a round U.S. Car plug-in connector at the rear. The photo I linked shows a U.S. Car connector. This provides a reverse light signal to power the camera that mounts at your rear license plate. You can also hardwire this camera system by making just two connections. You'll need to make a ground connection and also a reverse light signal connection at the car's taillights. The...
    view full answer...

  • Hitch and Wiring Installation on 2008 Mitsubishi Endeavor
  • For the 2008 Mitsubishi Endeavor, I would recommend the Curt Class 3 receiver hitch, part # 13113. To provide lighting for your trailer, we recommend the 4 Pole Harness and Hardwire Kit, part # C59496. The wiring kit includes a tester for locating the correct circuits and quick splices for tapping into the appropriate lighting circuits. You will need to access the rear of the tail light assemblies as if you were replacing a light bulb. Then, use the tester included in the kit to locate...
    view full answer...