I reached out to my contact at CIPA who said that the mirror that comes with the Replacement Side Mirror # CM46220 for your 1997 Dodge Dakota is 5"x7". view full answer...
The exterior dimensions for the Replacement Rubber Spacer for Thule Bed-Rider Truck Bed Mounted Bike Carrier # 853-5351 are as follows.
3-7/8 inches long, 1-1/8 inches wide, and 1-3/16 inches deep. view full answer...
The towing capacity of your 2004 Dodge Dakota is 3,400 to 4,650 lbs.
If you were to install the Curt Class 3 Trailer Hitch Receiver # C13145 which has a Gross Trailer Weight of 5,000 lbs and a Tongue Weight of 500 lbs your Dakota would be the limiting factor and you would still only be able to haul up to 4,650 lbs.
Please keep in mind that the Tongue Weight of your trailer should be between 10-15 percent of the GTW of your trailer. view full answer...
I have linked the installation instructions below for the etrailer Trailer Hitch Receiver # e53AR which fits your 1999 Dodge Dakota. This contains all the torque specs for the different fasteners in step 5. We do have the Digital Torque Adapter # PTM206 you can use with your 1/2" socket wrench to ensure you get the correct torque. view full answer...
I went and pulled a Brake Mounting Flange # 4-44-1 from our warehouse to measure it for you and found that from the center of the studs to the inside edge of the center hole it measures 1/2 of an inch and then from the center of the top bolt down to the center of the hole it measures 2 inches. view full answer...
The hose that is included with this Derale Series 8000 Plate-Fin Transmission Cooler Kit w/Barb Inlets, part # D135004, is 11/32 inch.
I have included a link to a FAQ below that has a lot of good information on transmission coolers, and suggested mounting locations. view full answer...
It is not recommended to use multiple hitch adapters or extensions when towing. Most adapters will cause a loss of hitch capacity since they move the actual load further away from the hitch, which increases leverage on the hitch tube.
This applies to both a straight 2-inch extension like the 18-inch Curt # C45796 and to dual-receiver adapters like # MPG544, both of which cost you half the hitch's rated capacity. Multiple adapters also tend to introduce more rattle and noise.
The better... view full answer...
When the Coil SumoSprings part # CSS-1069 is installed on a vehicle it won't add any height to the vehicle when unloaded but it well prevent sag when the vehicle does have cargo weight in it or towing a trailer with significant tongue weight. view full answer...
I called my contact at Tonno Pro about the Tonno Pro Hard Fold Hard Tonneau Cover part # TPHF-252 for your 2011 Dodge Dakota and they stated that the aluminum panels are .056" thick which equates to 17 gauge. Please note that the panels themselves are not really designed to bear weight but rather the crossbars that link them together. view full answer...
The Covercraft Large Tote Bag # ZTOTE1GY, you were looking at has dimensions of 24 inches long x 15 inches wide x 12 inches tall.
I went ahead and looked a little further into different options for you and found the following:
The largest duffel we have is the 36 inches long x 16 inches wide x 13 inches tall, it is made by Rightline # RL100D90.
Rampage has a Storage Bag # RA595001 that is 40 inches wide x 31 inches long x 7 inches tall.
These may be good options to look at but unfortunately... view full answer...
I spoke with my contact at Classic Accessories on the Classic Accessories Deluxe Heavy-Duty Cover for Teardrop Trailer, part # CA80198, and they said the width is 6-1/2 feet. They said the width is not listed because that cover is designed to fit the Forest River R-Pod 150 Series teardrop trailers, which they said are all the same width. view full answer...
The Dexter Hub/ Drum Assembly you referenced, part # 8-174-5UC3 uses 9/16 x 3 screw-in wheel studs, like part # 25-11.
We do not offer a 1/2 x 3 screw-in wheel stud, nor do our suppliers offer one.
To remove the wheel studs, you would use two lug nuts jammed together, like a reverse of the procedure shown in the video I will link you to. view full answer...
The overall height of the etrailer.com jack part # TJP-5001-Z that you referenced is 15-1/4 inches when fully retracted and since it has a travel distance of 10 inches the overall height when fully extended is 25-1/4 inches. view full answer...
I spoke with my contact at Derale, the manufacturer, to verify what thread size is used on your 2006 Dodge Dakota with the 4.7L V-8. He stated that it is the 3/4 inch - 16, like you referenced.
For an oil cooler that will fit your truck, he recommended the Derale Stacked-Plate Engine Oil Cooler Kit with Sandwich Adapter (Multiple Threads), # D15602, for a stacked-plate design. For a tube and fin design, go with the Derale Tube-Fin Engine Oil Cooler Kit with Sandwich Adapter (Multiple Threads),... view full answer...
In order to install the Westin Fey Diamondstep Rear Bumper part # 63000 on a 1995 Dodge Dakota you will also need the Custom Installation Kit for Westin Diamondstep Bumpers part # 97800 or you can just use the Westin Fey Diamondstep Rear Bumper with Custom Installation Kit part # 63000-97800.
The bumper mounting brackets are specific to both the frame and bumper which is why you cannot reuse the factory bumper mounting brackets unfortunately. view full answer...
I have a coworker who drives a 2001 Dakota which is the same generation as your 2000. So I checked his owners manual, see pictures. It appears that the bigger V8 for this truck, the 5.9, does not have enough capacity to tow an 8,000 pound trailer. The highest of any model is 6,450 pounds.
Capacity takes into account not only the motor but also the transmission, the rear end gear ratio, wheels, tires, suspension and so on. Basically you would have to replace every major component of the... view full answer...
The distance between the two holes on the front of the Westin Safari Light Bar with Installation Kit # 30-0005-1085 that you referenced is 18-1/2 inches.
This should work well on your 2003 Dodge Dakota as it is confirmed to fit your vehicle. view full answer...
I went out to the warehouse and was able to get my hands on the Demco Tow Bar Adapter for Roadmaster XL and EZ Series Base Plates # DM9523001 and got the following measurements:
-The overall length of 34",
-The distance between the outmost tabs, 33-1/8",
-The distance between the next outermost tabs, 25-5/8",
-The distance between the innermost tabs, 23-3/8",
-The depth of the shorter of the two tabs (E) 3-5/8", & the depth of the longer of the two tabs (F) 4-1/4".
I have included... view full answer...