To select replacement electric drum brakes for your tandem axle travel trailer you will want to confirm the axle weight rating, which can be found on the axle itself or on the trailer's main identification sticker. You also want to confirm the brake flange mounting bolt pattern and the size of the hub/drums. The brakes you referenced, part # AKEBRK-35-SA, are for 3500-lb axles with 10 x 2-1/4-inch drums and they use a 4-bolt mounting pattern.
If you want to add electric drum brakes to... view full answer...
The Curt Adjustable Width Trailer Hitch Receiver for RVs # 13703 is a great option. It's extremely versatile since it can be bolted or welded on and fits C-channel, I-beam, and box frames. It's designed to fit frames from 22 to 72 inches wide.
You may want an adjustable ball mount on the RV like the B&W Tow & Stow # BWTS10037B. This comes with two different sized hitch balls and has a 5 inch drop and 5-1/2 inch rise.
You'll will want to check with the DOT in your area and the areas... view full answer...
Nearly all A-frame trailer have a 50 degree angle frame, the Demco A-Frame Trailer Coupler # DM14793-81 that you referenced has a 50 degree angle too. view full answer...
For your Truckhero Elevate TS rails on your 2018 Ford F-150 I recommend the Yakima OverHaul HD Adjustable Truck Bed Ladder Rack for Tonneau Cover # Y01151-5755. These crossbars are an excellent choice that have an on road capacity of 300lbs and an off-road capacity of 180lbs. Additionally, these bars can be adjusted anywhere from 19 to 30 inches to accommodate your load or gear carrying needs. view full answer...
I would be happy to help!
Since we have already installed the Draw-Tite Trailer Hitch Receiver # 76145 you were looking at on a similar 2018 Dodge Challenger we already have the required measurements on hand.
With the hitch installed you will have 6" from the center of the hitch pin hole to the most outward edge of the rear bumper, and only 9-1/4" from the ground to the top inside edge of the receiver so you will need a rack with a raised shank.
I recommend the Hollywood Racks Trail... view full answer...
For the Draw-Tite Max-Frame Trailer Hitch item # 76145 you are going to want the Curt Towing Starter Kit for 2" Hitches item # C45534. This towing kit will provide you with a 2" ball and a fixed ball mount with a 3/4" rise and 2" drop. It also includes a hitch pin and clip, hitch receiver lock with keys, hitch cover, and a storage case.
This hitch is confirmed to fit your 2010 Dodge Challenger unless you have the quad tip exhaust. If you have the quad tip exhaust you will want the Curt... view full answer...
The MagnaFlow Stainless Steel Catalytic Converter Set part # MF16420 which is a fit for a 2010 Dodge Challenger SRT8 will not cause any check engine lights to appear. view full answer...
One of the best single bike rack we have is the RockyMounts HighNoon FC Solo Bike Rack for 1 Bike - 1-1/4" and 2" Hitches - Wheel Mount # RKY87RR, which is a hitch mounted bike rack. This is a platform rack that secures to the wheel of the bike, as well as integrated hitch and bike locks for maximum security of the bike.
If you don't already have a hitch installed, I recommend Curt's Class III hitch, part # 13456 which is compatible with vehicles with and without the quad exhaust. I've... view full answer...
I spoke with Fulton and parts are no longer available for the Fulton 945. That's a pretty old winch.
For a new similar replacement they suggest # F143100. A 1,500 pound capacity winch that's designed to be used in marine applications. view full answer...
The Curt hitch part # C12064 that you referenced has been confirmed as a fit for your 2015 Dodge Challenger. Although the install video I attached shows a slightly different vehicle the install on your vehicle would be the exact same.
The jack points for the vehicle will be just in front of the rear wheels, but you will need to consult your owners manual to determine exactly where they are located. view full answer...
First you will need to verify the exact receiver you have for your 2012 Dodge Challenger. I have listed the different receivers we carry below. Once you have verified the correct receiver number you can go to the Replacement Hardware Kit # RHK and enter in the appropriate number in the box to ensure you get the correct hardware needed to install your receiver.
Draw-Tite Max-Frame Trailer Hitch Receiver # 76145
Draw-Tite Trailer Hitch Receiver # 36548
Curt Trailer Hitch Receiver # C12064
Curt... view full answer...
Since you are experiencing hyper flashing with your LED lights, using a load resistor like # DI34ZR per affected light is correct. However, I would remove the 4 load resistors you added to the rear center lighting.
I recommend using the LED load resistor # DI34ZR because it's 50 watts. Replace one first and see if it helps. If it helps the sync problem, then use this load resistor for each light.
A load resistor can become hot because it is designed to hold back power. Wrapping them... view full answer...
The Curt Trailer Hitch Receiver part # C13236 weighs around 32 lbs and the Curt Trailer Hitch Receiver part # C12064 weighs about 26 lbs. The Curt C12064 is a 1-1/4" hitch receiver and the Curt C13236 is a 2" receiver. I normally recommend a 2" hitch because you will have more options for bike racks and other accessories. They also normally offer more weight capacity.
In this case I do recommend the 1-1/4" hitch part # C12064 because it is a concealed cross tube hitch so the only portion... view full answer...
The ball mount that comes with the Curt Trailer Hitch, # 12240, has a rise of 2-5/8 inches and a drop of 3-1/4 inches. Its overall length is 7-1/4 inches. It accepts a ball with a 3/4 inch diameter shank.
I have included a link to the installation details for this trailer hitch below. view full answer...
You are in one of those tricky situations where on one had you have to have tire chains to be able to drive in certain areas but the manufacturer of the vehicles states that no tire chains can be used on the vehicle.
Your best option will be the Thule Tire Chains # TH2004205117 as they are Class S compatible which means they require minimal tire clearance and they install easy plus are very durable.
But you basically will have to contact a Mopar dealer in the area where you plan to travel... view full answer...
Hello, I recommend the Draw-Tite Class III Max Frame Receiver Hitch # 76145 for your 2018 Dodge Challenger as long you do not have the Quad-Tip Exhaust; this is rated at a 675 lb. tongue weight. If you do have the the Quad-Tip Exhaust, I suggest the Curt Trailer Hitch Receiver # C13236.
The wiring connections I recommend is the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118656.
All items I recommend here are confirmed fit for your 2018 Dodge Challenger. I have... view full answer...
I reached out to Rear View Safety regarding their Wireless Cameras like the part # RVS-83112-WIFI that you referenced and found that the app that is needed to view the camera on your phone likely isn't compatible with Android Auto or Apple CarPlay. This means you wouldn't be able to sync it to the in-dash monitor (either factory or aftermarket) in your Challenger so that you can use it to view the camera.
At this time we do not have a wireless camera system that can be used in this manner.... view full answer...
I apologize for the confusion, but basically the Curt hitch part # C12064 fits both the the quad tip and non-quad tip versions of the 2019 Dodge Challenger so it will fit and work well for you.
I attached an install video link to this page plus a picture of what it looks like installed for you to check out too. view full answer...
The Vehicle to Vehicle Tail Light Converter # C56196 will allow you to separate your stop and turn signals on your 2010 Dodge Challenger. While there is not a diagram with any wire colors, you will be able to find the right wires easily by using the Cordless Circuit Tester # PTW2979.
Please keep in mind it is recommended you use Diodes # 48955 to prevent power feedback.
I have added a link to a video review of the converter for you to check out as well. view full answer...
I do have a solution that would allow you to carry 3 bikes with your 2010 Dodge Challenger, but there are no trunk-mounted bike rack options that are confirmed to fit your vehicle.
What I would recommend you do is get a Curt Hitch # 13465 and get a 3-bike hitch mounted bike carrier. I attached installation instructions and an installation video for this hitch for you to check out.
For a 3-bike rack I would recommend you get a Swagman Trailhead 3 Bike Rack # S63365. This rack has anti-sway... view full answer...