The installation instructions for the Curt Class I receiver # C11133 specifically mention the procedure for installing the hitch on dual exhaust-equipped vehicles, to the hitch is indeed compatible with your vehicle.
The procedure specific to dual exhaust vehicles is mentioned in step one of the instructions, which you can see by clicking on the link provided. view full answer...
When it comes to the replacement cradles for your Rhode Gear 2 Bike Rack The Replacement Cradle for Rhode Gear and Prorack Highway Bike Racks # RG8890083 is the only replacement cradle that we will have. It has a dimension of 1-5/8 inch x 2-1/8 inch x 4-1/2 inch, with an inside diameter of 1-3/32 inches.
This cradle fits The Rhode Gear Highway Bike Carriers listed below:
8015200
8015201
8015202
8015215
8015216
8015218
8015219
8015220
8015221
It also fits Prorack 2 Bike Rack for 1-1/4... view full answer...
There is an underbody panel that will need to be trimmed or removed to install la hitch on a 2015 Chrysler 200 but no bumper fascia trimming.
I recommend Draw-Tite trailer hitch # 24919. It is the most popular option for your 200. I have linked the instructions for you to view.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited... view full answer...
For your 2015 Chrysler 200, a maximum of two bikes is able to be carried with the trailer hitch that fits it, the Draw-Tite Sportframe Trailer Hitch Receiver # 24919.
The reason is, this 1-1/4 inch hitch is a Class I hitch, and Class I hitches are only rated for carrying up to two bikes due to the amount of stress that would be put on the hitch and your Chrysler's frame with a 4-bike rack. So what you would need instead is a Class I compatible 2-bike rack such as the Swagman Trailhead... view full answer...
Yes, the power wire routing instructions for a trailer wiring harness like the Curt T-connector # C56242 for a 2015 Chrysler 200 are usually pretty generic as there are more than one way to route the wire. I don't have exact instructions for you unfortunately as the manufacturer does not provide any and we have not yet done this on this vehicle. That said, I recommend first finding a grommet in the trunk pan to route the wire through and then once you get it outside the vehicle, following... view full answer...
According to Saris, their # SA805BL Bones two bike trunk mounted bike carrier isn't compatible with the convertible model.
Hollywood Racks offers several 2 bike models that will fit. I'd recommend their Express 3 bike model, part # HRE3. However, this will not fit if your 200 is equipped with the factory spoiler.
If you do have a spoiler, I recommend the Malone Hanger Trunk Bike Rack for 3 Bikes - Adjustable Arms # MPG2139, you can use it with 1, 2, or 3 bikes. This rack is confirmed... view full answer...
Yes, I can email you the installation instructions for Draw-Tite trailer hitch # 24919. Installation is not difficult at all on your 2015 Chrysler 200.
If you plan on doing any towing first consult the vehicle owners manual to make sure it is permissible to do so. For a ball mount use # 3593. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # C56242.
If you want to use the hitch for a bike rack or cargo carrier then make sure that the item... view full answer...
Yes, the Thule Force XT XXL Rooftop Cargo Box # TH6359B referenced in your question will fit and work great with the Thule AeroBlade Load Bars that are on your 2015 Chrysler 200.
This is an excellent, aerodynamic cargo box that features a carrying capacity of 22 cubic feet. Its dual-side-opening lid will let you load and unload gear from either side of your Chrysler 200 and 2 Thule locks are included to protect your cargo. view full answer...
All of the carriers like the Yakima EXO Swing Away Enclosed Cargo Carrier - 2" Hitches - 10 cu ft - 100 lbs # Y62VR that will swing away from your vehicle require a 2" hitch. The only hitches available for your Chrysler 200 are 1-1/4" receivers.
You could use a standard cargo carrier like the # C18110 on your 1-1/4" hitch to carry golf clubs or other cargo. view full answer...
The replacement key you need is probably the Thule key # THKEYN021. If you want to send me pictures of your roof rack to verify feel free.
It's not likely the entire roof rack from you old vehicle will fit the newer 2013 Chrysler 200 but parts of it probably will. If you reply with the year, make, and model of the vehicle the roof rack is coming from I'll see what if anything is compatible. view full answer...
I spoke with my contact at Draw-Tite and he said that as long as it is a 2015 Chrysler 200 4-door sedan then trailer hitch # 24919 fits all models including the 200s.
If you will be using the hitch for light duty towing then the correct ball mount is # 3593. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring you can use # C56242.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory... view full answer...
It looks like you're on to Mopar's little game! Chrysler is no different than any of the other car manufacturers in wanting you to purchase parts from them, rather than something available in the aftermarket that's much more reasonably priced.
The recommended Curt trailer wiring harness for your vehicle is the # C56211 wiring harness. The C56134 harness you mentioned has been discontinued and is no longer available.
The design of the C56211 actually draws the voltage to power the trailer... view full answer...
Thanks for the purchase and there is a threaded locking hitch pin that will work with your Curt Cargo Carrier for 1-1/4" and 2" Hitches # C18145. We have found that the Locking Anti-Rattle, Threaded Hitch Pin # S64029 is a fit for your cargo carrier and will work great to stabilize the carrier as well as help keep it secure from any miscreant with sticky fingers. view full answer...
Your best and safest way to fit your 2" bike rack onto your vehicle's 1-1/4" hitch receiver, all while increasing ground clearance, is to use Hitch Adapter 1-1/4" to 2" Trailer Hitch Receiver with 5" Rise # HT5R. Keep in mind this adapter will reduce your hitch's tongue weight capacity by 50%. For example, the Draw-Tite # 24871 on your 2014 Chrysler 200 has a max tongue weight of 200lbs, but with the adapter you will have a max tongue weight of 100lbs. I have attached a demonstration video... view full answer...
The correct Bearing Buddy Bearing Protector like part # BB1980A will be the one that matches the inner diameter of the hub bore opening on the trailer hub. In order to obtain the correct Bearing Buddy Bearing Protector you''ll need a digital caliper and measure to the nearest thousandth of an inch. I have attached a list of our Bearing Buddy Bearing Protectors below.
Unfortunately, I can't recommend using the wrong size Bearing Buddy in hopes it will fit. Therefore, my suggestion is to... view full answer...
If you are looking for a good entry-level bike carrier the Thule Passage 3, # TH911XT is a good choice. This is a basic carrier with anti-sway cradles and it will secure to your 2015 Chrysler 200s using 6 straps.
The next step up is going to be the Gateway, # TH78VR, which has an upgraded style and design from the Passage. The Gateway Pro, # TH78VR, has the same basic design as the Gateway only it features upgraded cradles with road dampening technology, and an integrated cable lock.
But... view full answer...
Yes, the Draw-Tite trailer hitch # 24871 will fit your 2014 Chrysler 200 Limited. It will fit all models including the convertible models.
If you plan on doing some towing please first consult the owners manual to determine the towing capacity of the vehicle.
For a ball mount use # 3594. And for a 1-7/8 inch ball use # 19256. For a 2 inch ball use # 19258. For trailer wiring you can use # C56211. I have linked the installation instructions for the hitch and wiring and a video showing... view full answer...
For your 2011 Chrysler 200, we have a confirmed fit for both the Draw-Tite Sportframe Trailer Hitch Receiver # 24871 and the Curt # C11133. The Draw-Tite hitch will be recessed too far under your bumper for a cargo carrier, so I recommend the Curt hitch which will require stabilizer strap # 18050 and has a measurement of 4-1/2 inches from the center of the hitch pin to the outermost part of the bumper. You will simply need a Class I rated cargo carrier with the closest part of the rack... view full answer...
We do have everything you need to tow a jet ski with your 2015 Chrysler 200. I recommend using the Curt Trailer Hitch # C11403 along with the Curt T-Connector Wiring # C56242. You also need the Ball Mount # C45521, either a 1-7/8" # A-80 or 2" # A-82 hitch ball, and then a pin and clip # F-4 to complete the towing setup.
While we do have all of the components needed to tow a small trailer with your Chrysler 200, I tried to find a trailer towing capacity in the online owner's manual and... view full answer...
I checked with Thule and the fit dial setting for the Passage bike rack, # TH910XT, on a 2011 Chrysler 200 sedan should be set to 7. This is the optimal position for your vehicle. In addition, you will also place the top clips in the gap at the front edge of the top of the trunk, place the lower clips in the bottom edge of the trunk, and the lower arm of the carrier should be positioned on the upper tier of the bumper.
I have included a link to the installation instructions for you to... view full answer...
Go To Results