Expert Answers about Chrysler 200
- Is it Necessary to Connect the Power Wire to the Battery on a 2013 Chrysler 200
- Yes, it is necessary to run the lead from the Wiring # C56211 that runs from the battery to the trailer connector. This wire carries the voltage necessary to power the trailer lamps. The wires that are connected to the tail light assemblies tell the converter that the vehicle tail lights, turn signals or brake lights are operating, but do not provide the voltage for the lamps.
Vehicle manufactures have determined that the circuits feeding the tail light assemblies on the vehicle cannot...
view full answer... - Routing the Power Wire for Trailer Wiring Harness on a 2014 Chrysler 200
- There are different ways that you can route the power wire for trailer wiring harness # C56211. It all depends on how you want the wire to be ran. I have included a link to the right to our help article with tips on different ways to route the power wire.
view full answer... - Installation and Operation Instructions for the Curt Stabilization Strap on a 2013 Chrysler 200
- I can help show you a little better what this strap will look like when installed on your vehicle.
While there is no specific video to your 2013 Chrysler 200, I do have two videos that demonstrate the stabilization strap # 18050 be used with the non-trailer loads, which are going to be most commonly bike racks and cargo carriers.
The Curt hitch # C11133 is a confirmed fit for your 200, but if you would rather not use a strap, like most customers don't when setting up your accessories,...
view full answer... - How Does the Rightline Gear Sport 2 Roof Cargo Bag Attach to a Vehicle without a Roof Rack
- Rightline Gear Sport 2 bag # RL100S20 was meant to sit on the roof of a vehicle. In order to secure it to the roof on a vehicle that does not have any sort of roof rack you will need to route the straps through the interior of the vehicle. Just connect the bag's straps to the naked roof straps, and feed them through your vehicle's open car doors. Cinch the straps tight to secure the bag in place.
view full answer... - Trailer Hitch and Wiring for a 2015 Chrysler 200
- The instructions for trailer hitch # 24919 are linked here and on the product page. Look for the black and white wrench icon.
The proper ball mount is # 3593. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. For trailer wiring use # C56242. Its instructions are also linked here and on its page.
view full answer... - What are the Correct Settings for the Thule Passage Trunk Mount Bike Rack on a 2011 Chrysler 200
- I checked with Thule and the fit dial setting for the Passage bike rack, # TH910XT, on a 2011 Chrysler 200 sedan should be set to 7. This is the optimal position for your vehicle. In addition, you will also place the top clips in the gap at the front edge of the top of the trunk, place the lower clips in the bottom edge of the trunk, and the lower arm of the carrier should be positioned on the upper tier of the bumper.
I have included a link to the installation instructions for you to...
view full answer... - Trailer Hitch for a 2015 Chrysler 200
- Yes, I can email you the installation instructions for Draw-Tite trailer hitch # 24919. Installation is not difficult at all on your 2015 Chrysler 200.
If you plan on doing any towing first consult the vehicle owners manual to make sure it is permissible to do so. For a ball mount use # 3593. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # C56242.
If you want to use the hitch for a bike rack or cargo carrier then make sure that the item...
view full answer... - Difference In Installation of Trailer Hitch Between Single and Dual Exhaust 2016 Chrysler 200
- I took a look at the installation instructions of the Draw-Tite # 24919 hitch (which are also linked for you) and found the only difference when installing it in the single or dual exhaust models of a 2016 Chrysler 200 are that the single exhaust models require trimming of the underbody panel.
Apart from that they are the same bolt-on installation and will not require any drilling in your Chrysler's frame.
view full answer... - Tilting and Folding Enclosed Cargo Carrier
- All of the carriers like the Yakima EXO Swing Away Enclosed Cargo Carrier - 2" Hitches - 10 cu ft - 100 lbs # Y62VR that will swing away from your vehicle require a 2" hitch. The only hitches available for your Chrysler 200 are 1-1/4" receivers.
You could use a standard cargo carrier like the # C18110 on your 1-1/4" hitch to carry golf clubs or other cargo.
view full answer... - Routing Power Wire for T-One Vehicle Wiring Harness on 2015 Chrysler 200
- Yes, the power wire routing instructions for a trailer wiring harness like the Curt T-connector # C56242 for a 2015 Chrysler 200 are usually pretty generic as there are more than one way to route the wire. I don't have exact instructions for you unfortunately as the manufacturer does not provide any and we have not yet done this on this vehicle. That said, I recommend first finding a grommet in the trunk pan to route the wire through and then once you get it outside the vehicle, following...
view full answer...
Go To Results