When installing the Roadmaster Front Anti-Sway Bar and TruTrac Rod Kit # RM-1259-106 you will want those brackets sit flush; you can enlarge the hole or drill a new one so that you can get the bracket sitting flush to the rail. My contact over at Roadmaster also recommended using Red Loctite # LT37420 when completing the installation, if you don't already have some. view full answer...
The Roadmaster Front Anti-Sway Bar # RM-1259-105 uses a similar mounting location to the Roadmaster TruTrac Front-Axle Trac Rod # RM-TRACW-22 but the exact mounting locations are different enough that these 2 products won't interfere at all and you won't need to overlap any of the mounting brackets. When I reached out to my contact at Roadmaster he said that the sway bar mounts more towards the back while the TruTrac bar mounts more to the front and there isn't any overlap so you don't... view full answer...
The Air Lift LoadLifter 5000 Air Helper Springs part # AL57202 which are a fit for the Workhorse P30 Chassis will require you to remove the existing jounce springs. The air springs will also require drilling into the frame but only a few holes so nothing too major. The Air Lift LoadLifter 5000 Air Helper Springs are the best option for the Workhorse P30 Chassis so they are worth the extra troubles for installation. view full answer...
I'd recommend you use our Brake Controller Installation Kit, part # ETBC7, The kit includes a 4-pole to 7-way adapter. If you no longer need the 4 pole round connector, you can simply remove it, and wire it directly to the 4-pole provided by the adapter after you cut the connector off.
The kit also includes all the hardware and circuit breakers you'll need to complete the installation. 25 feet of wire is included, but you'll need additional # 10-2-1 wire due to the length of your motorhome.... view full answer...
The Roadmaster Front Suspension Bar for Motor Homes with Factory Anti-Sway Bar # RM-1109-200 that you referenced does not replace the factory sway bar. It installs with it to balance weight transfer and reduce body roll on your 2003 P32 chassis.
The part # RM-1109-200 is also known as the Roadmaster Spreader bar.
Check out the installation instructions I attached for this product. view full answer...
The Camco Replacement Propane Extension Hose - Male and Female # CAM59043 should be able to connect to the # CAM59143 without any issues. It is the same brand with the same connectors and the 12' hose has a male and female end so they are compatible. view full answer...
I believe that there is wiring located up under the dash and to the left of the steering column on the 2008 Workhorse W22 chassis that is for a brake controller. Look for a bundle of wires held together with a white tag. The tag shows the functions of the wires. If that wire bundle is not present on your Bounder then the brake controller will have to be hardwired in.
You would need a 30 amp circuit breaker, # PK54530, wire # 10-2-1 sold by the foot, and some additional # 10-1-1 wire sold... view full answer...
Thank you so much for the purchase! And yes, the vacuum breaker should indeed be pointing upwards when you install the Empire Faucets RV Shower Valve w/ Vacuum Breaker # EM72FR. view full answer...
Not all SumoSpring kits install the same. The part # SSR-280-54-1 that you referenced though does not require drilling unlike others.
I attached a set of install instructions for you to check out as well. view full answer...
The Dometic Full-Timer RV Toilet # DOM87FR you were looking at includes a new seal, new mounting studs, washers, nuts, and caps which is everything needed to install the toilet.
To get the # DOM87FR installed you will need to remove the two nuts holding the toilet down then remove the old toilet. Slightly loosen the screws near the studs on the flange installed on the floor so you can remove the old studs then install the new studs. Next the seal should be installed on the bottom of the... view full answer...
The Kat's Heaters Defrost Fan # KH43100 referenced in your question is a 12 Volt, 2-speed fan that has just a single black wire that runs out from the base of the unit. You will simply need to run this to an available power wire to activate the fan, as it is grounded through the mounting hardware. view full answer...
The 7-way of your 2001 National Dolphin should have the 12 volt accessory circuit active on the 7-way unless it was damaged over the years. This means that with the Curt Echo part # C51180 you'd just need to plug the controller into the 7-way and once synced to your smart phone you'd be set. view full answer...
It sounds like you are looking for the Pigtail Wiring Harness part # PK11998 which will plug directly into the back of the 7- and 4-Pole Trailer Connector Socket part # HM40975. The Deka Heat Shrink Butt Connector part # DW05744-5 and part # DW05745-5 can then be used to make the above connections. view full answer...
If your 2004 Holiday Rambler has a 7-way at the rear of it there should be a bundle of wires under your dash with a white tag that has all of the wire functions labelled.
The Prodigy P3 part # 90195 has the following wire color functions. The white wire is the ground wire, the black is the 12 volt power circuit, the red is stoplight circuit, and blue is brake output. view full answer...
Steering stabilizer # RM-RSSCP30 is a replacement for the OEM damper on your 2004 Workhorse P series motor home. This unit does have a return to center feature. I have included a link to the installation instructions for you to the right. view full answer...
It sounds like your 2003 Pace Arrow 37A has switches in 2 places on the coach to allow you to control the water pump, which won't be an issue with the Seaflo Diaphragm Pump for Boats and RVs - Variable Flow - Up to 5.5 GPM - 1/2" MPT - 12V # SE24FR. You'll install this unit just as it was connected to your old water pump.. In regards to the "quick connect" hose fittings, I'm not aware of a water pump that offers those included and I believe it's something you would have to come up with... view full answer...
The Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88101 for your 2004 Workhorse W-Series do have the ability to level your Workhorse front to back and side to side. If you have a well centered load, then putting air in the right bag would likely require you to also put air in the left bag.
If you have an off center load, then you may need more air in one bag versus the other. Air Lift does not provide a "distance" for the air bags. The bags are designed... view full answer...
When installing the AirLift # AL88101 you do not need to remove the factory jounce bumpers and they will not be installed in the same place. You will want the air bags to install forward of the axle and your stock jounces should be behind the axle. Additionally, because of their size, the AirLift bags will engage before the stock jounces so they can be removed if you desire. view full answer...
Yes, it is necessary to relocate and reinstall the factory jounce spring when installing the Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88202.
The Air Lift LoadLifter 5000 Ultimate Air Helper Springs with Internal Jounce Bumpers # AL88202 is designed to work in conjunction with the factory jounce and the factory jounce "must" be relocated under the frame above the axle. The internal jounce in the spring system is more of a fail safe that protects... view full answer...
The two MaxxFan Mini Plus Manual RV Roof Vent w/ 12V Fan # MA00-03851 you bought will have black and white wires hidden above the fan that you'll connect to the 12v wiring of the trailer. The black wire is your power and the white wire is your ground/neutral. To connect it to the trailer's wiring you'll need to use some butt connectors # DW05714 or wire nuts to splice the wiring together. If there isn't 12v wiring in the locations near the vents then you'll need to run some 14 gauge wire... view full answer...