Expert Answers about Workhorse W-Series
- Anti-Sway Bar Fit For 2009 Winnebago Sunova on Workhorse W18 Chassis
- The best option to stabilize your 2009 Winnebago Sunova on a Workhorse W18 chassis are definitely anti-sway bars. These will engage and counteract the transferring of weight that occurs when you are turning and in windy conditions, particularly when you have a dinghy like your '21 Ranger.
Anti-sway bars act as a brace between the frame of your motorhome, and are better constructed with higher-strength, thicker steel than OEM sway bars. This means they are stronger with much higher roll...
view full answer... - Steering Stabilizer That Fits 2008 Safari Simba Series 33SFS on Workhorse Chassis
- Based on my research, your 2008 Safari Simba Series 33SFS was built on a Workhorse W22 chassis, which means the correct steering stabilizer is the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes # RM-RBK13-RSSA.
I have added a link to a video review of this stabilizer for you to check out as well.
view full answer... - Correct Front SumoSprings for a 2009 Workhorse W-22 Chassis
- The correct SumoSprings Solo Custom Helper Springs for a 2009 Workhorse W-22 Chassis is part # SSF-280-47 which is sold as a pair. I have attached an install video I did below as well.
view full answer... - Roadmaster Anti-Sway And Stabilizing Systems For Workhorse W24 Chassis
- For your 2010 Winnebago Adventurer 37F with 2009 Workhorse W24 Chassis, the Roadmaster Reflex Steering Stabilizer with Mounting Brackets for Class A Motor Homes # RM-RBK13-RSSA is a great choice and a confirmed fit. It keeps your motorhome in line by constantly working to maintain its position. It minimizes wander and corrects oversteering so the driver doesn't need to work as hard to steer so it reduces fatigue.
The Roadmaster Front Anti-Sway Bar for Motor Homes # RM-1259-106 improves...
view full answer... - Replace Motor for Kwikee Motor part 90321100
- Thanks for all the info on your steps! Based on that I was able to confirm that the replacement motor is part # LC379147.
view full answer... - How Thick Are SnapPad Jack Pads
- The bottom portion of the SnapPad Jack Pads # SP54FR2 are approximately 1" thick but they are not meant to lift your wheels off the ground. If your wheels came off the ground that would mean you're putting the full weight of your RV onto the jacks, which is not recommend. These pads are meant to be installed on your jack feet to eliminate the need to crawl under your motorhome to position plastic pads or wood blocks. It also increases the surface area of your leveling jack's feet to provide...
view full answer... - Correct Replacement for Kwikee Series 23 Steps Model 902308000
- I reached out to the manufacturer who told me the Kwikee Series 25 Steps # LC365837 you are looking to replace your older steps with will not work. This is what they told me:
"Per my parts department, based on the information you have provided, they can verify that the customer is replacing a Series 23 Kwikee step assembly with a series 25 Kwikee step assembly. He needs to be advised not to do this, as they will not fit or bolt up properly. The frame sizes are different from one another...
view full answer... - Sway Bar Recommendation For 2003 Workhorse W-Series 22
- According to my research the Roadmaster Rear Anti-Sway Bar part # RM-1259-109 will install on the 2004 Newmar Scottsdale that is on a 2003 W-22 Workhorse chassis. The Newmar Scottsdale from my research is 33-1/2 ft so according to Roadmaster you will not have any issues installing the sway bar. If the motor home was shorter than 33 ft the sway bar would not fit properly and you would need part # RM-1259-108.
The metal box in the photo does not interfere with the installation location...
view full answer... - Trailer Hitch Option For 2006 Itasca Suncruiser
- We have a hitch option for your 2006 Itasca Suncruiser, but the # C15400 is 32.94" wide overall and the bolt holes are 30.31" apart from each other. So what you will need is a universal weld-on hitch, which will fit so long as the frame on your motorhome measures no more than 44" outside to outside:
- Curt Class 5 Universal Weld-on Hitch w/ Brackets - 2" Receiver - 44" Wide # C47CR
view full answer... - Recommended Rear Anti-Sway Bar For A 2003 Itasca Winnebago Suncruiser Class A Motorhome
- The thicker the diameter of the anti-sway bar the better it's going to preform. The Roadmaster Rear Anti-Sway Bar # RM-1259-108 has a 1-1/2" bar diameter and the Roadmaster Rear Anti-Sway Bar # RM-1259-109 has a 1-3/4" bar diameter.
This means that the # RM-1259-109 is going to be slightly better at minimizing the sway and body roll you feel when traveling on the highway or when making tight turns.
Note: If your 2003 Itasca Winnebago Suncruiser has Firestone Ride-Rite air bags then...
view full answer... - Air Bag Helper Springs For a 2003 Dolphin RV Motorhome On a Workhorse W-22 Chassis
- The Air Lift LoadLifter 5000 Ultimate Air Helper Springs # AL88101 are confirmed to fit the front of your 2003 Dolphin with the Workhorse W22 chassis. These have the internal jounce bumpers that will help to reduce bouncing and reduce the risk of damage to the bags in the event they become under inflated.
We also have the matching Air Springs # AL88202 for the rear suspension. These also have the internal jounce bumpers.
I recommend using the Air Lift WirelessAIR Compressor System #...
view full answer... - Does Roadmaster Reflex Steering Stabilizer RM-RBK13-RSSA Fit 2010 Winnebago Workhorse W24
- The steering stabilizer we offer that is designed to work with your 2010 Workhorse W24 is part # RM-RBK13-RSSA.
This attaches to the steering mechanism on one end and on the other end attaches to the chassis undercarriage. This stabilizer helps you keep control of your motorhome and help correct over-steering when you are in high winds or driving on uneven roads.
view full answer... - Wiring for Prodigy P3 Brake Controller on 2004 Workhorse W22 Chassis
- There isn't a brake controller port that I am aware of on your motorhome built on a 2004 Workhorse W22 chassis, but you can check up under the dash for a bundle of wires; they would have a white tag on them. It would generally be to the far left side under the dash if they are there.
If those wires are there you would be able to simply splice in the Tekonsha Prodigy P3 Trailer Brake Controller # 90195.
If that bundle of wires is not there you will need the Wiring Kit for 2, 4, 6, and...
view full answer... - Steering Stabilizer for a 2007 Fleetwood Bounder
- Your 2007 Fleetwood Bounder is built on a Workhorse W Series chassis so for a steering stabilizer you would want the part # RM-RBK13-RSSA which is a confirmed fit and would work well.
The sturdy steel spring on this stabilizer keeps your vehicle in line by constantly working to maintain its position. Mount it between the steering mechanism and the chassis for a tight connection that will minimize wander and correct oversteering.
view full answer... - Where Is The Roadmaster TruTrac Front-Axle Trac Rod Manufactured # RM-TRACW-22
- The Roadmaster TruTrac Front-Axle Trac Rod for Large Trucks and RVs # RM-TRACW-22 is manufactured in-house at Roadmaster's Vancouver, Washington facility. We list it as being made in the USA and I called Roadmaster as well and confirmed it, so you don't have to worry about using a non-American made trac rod on your 2003 Workhorse W22 Motorhome.
view full answer... - Steering Stabilizer for a 2008 Fleetwood Bounder on a 2007 Workhorse W22 Chassis
- The Roadmaster Reflex steering stabilizer that fits the 2007 Workhorse W22 chassis is actually # RM-RBK13-RSSA. The one that you referenced, # RM-RBK14-RSSA, is for Freightliner chassis.
The steering stabilizers will come with the mounting brackets and hardware. Current pricing is available on each product page.
view full answer... - Replacement Bellows For An Air Lift LoadLifter 5000 Ultimate System
- Since you have a Workhorse W22 Chassis you should have the Air Lift LoadLifter 5000 Ultimate System # AL88202 which would mean you need the Replacement Air Spring for Air Lift LoadLifter 5000 Ultimate System - Rear Axle # AL84201 to replace the bellows.
If you don't have the "Ultimate" and have a different model then let me know and I can find the correct replacement for you.
view full answer... - Timbren vs SumoSpring for Front of 2005 Workhorse W22
- The Timbren front kit part # TWFRW22 that fits your 2005 Workhorse W22 is much stiffer than the # SSF-280-47 you have now. If stiffer and more supportive is what you want this would be the way to go. If you are wanting a softer ride though this is probably not going to be it.
view full answer... - Upgraded Sway Bars that Fit 2006 Itasca Built on Workhorse W Series Chassis
- I did some digging on your 2006 Itasca and it looks to be built on a Workhorse W series chassis so for a rear sway bar you'd want the part # RM-1259-108. Then for the front bar you'd want the part # RM-1259-105.
view full answer... - Replacement Air Line Hose For Roadmaster BrakeMaster Supplemental Braking System
- You can obtain the replacement air line right here for your Roadmaster BrakeMaster Braking System # RM-9060. The air line hose is sold by the foot so you can get the exact amount you want, with the correct part number being the following:
- Air Line Hose 1/4" for BrakeMaster Systems # RM450700
view full answer...
Go To Results