Correct Front SumoSprings for a 2009 Workhorse W-22 Chassis

Question

Question:

Im about to order Sumos for the front axle of my 2009 Workhorse W-22. I want to make sure this is the correct part # and if they automatically come as a pair I only need to one as my order quantity.

asked by: Bob H

1

Helpful Expert Reply:

The correct SumoSprings Solo Custom Helper Springs for a 2009 Workhorse W-22 Chassis is part # SSF-280-47 which is sold as a pair. I have attached an install video I did below as well.

expert reply by: Conner L

1

Answer 1

The trim ring is not available, but the Atwood RV Carbon Monoxide and Propane Gas Detector #AT36681 can be mounted quite simply without it. I attached a page from the directions which shows how this is done; you simply remove the bezel from the…

view full answer...

Answer 2

The only solution I have is for a complete replacement system. Unfortunately, the Atwood Leveleg system was discontinued so there is not a replacement jack available. For a replacement, I recommend the Lippert Ground Control 3.0 Electric 5th Wheel RV…

view full answer...

Answer 3

Yes, that is correct. When using the Roadmaster Tow Dolly with Electric Brakes - 4,250 lbs, part #RM-2050-1, you have to lock your steering wheel. I also recommend using a wheel lock as a fail safe. This way you have added protection you know your…

view full answer...

Answer 4

Yes, the Replacement Toilet Bowl Seal Kit for Dometic Sealand and VacuFlush RV Toilets #DOM35FR is the correct seal for your Dometic Sealand 210 Traveler Lite RV Toilet.

view full answer...

Answer 5

The only way I can help is with a complete replacement option as when Lippert bought out Atwood they discontinued the Atwood Leveleg parts so a replacement controller is no longer available. Instead I recommend replacing your system with the Lippert…

view full answer...

Answer 6

To know if the Phoenix USA Lug Nut Cover for 33mm Lug Nuts #PXSP33 will fit the lug nuts on your 2021 Tiffin Allegro Bus Motorhome you'll need to measure the diameter of the lug nuts. This lug nut cover fits 33mm lug nuts. If you find a different…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Correct Front SumoSprings for a 2009 Workhorse W-22 Chassis

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching