How Thick Are SnapPad Jack Pads

Question

Question:

How much height do snap pads add to the lift ? Will they take the wheels off the ground when the jacks are fully extended ?

asked by: Michael S

0

Expert Reply:

The bottom portion of the SnapPad Jack Pads # SP54FR2 are approximately 1" thick but they are not meant to lift your wheels off the ground. If your wheels came off the ground that would mean you're putting the full weight of your RV onto the jacks, which is not recommend. These pads are meant to be installed on your jack feet to eliminate the need to crawl under your motorhome to position plastic pads or wood blocks. It also increases the surface area of your leveling jack's feet to provide added support for your motorhome, which will help prevent your motorhome from sinking into soft ground, unlike smaller metal feet.

expert reply by: Kevin C

0

Answer 1

In regards to the SnapPad Jack Stand Pads, if you have round shaped feet then you would measure the diameter from end to end. If the feet measures 9" then you can use part #SP54FR2. I have attached a full list of options below but there are no…

view full answer...

Answer 2

That's a good question and the difference between the two SnapPad Jack Stand Pads for Motorhome are different shapes and depths, it isn't solely the notch in the center. I added photos of the two pads side-by-side so you can see the…

view full answer...

Answer 3

They can be! For a single 9" round SnapPad, like what you referenced in part #SP54FR4, you'll need the part #SP54FR.

view full answer...

Answer 4

I spoke with my contact at Lippert and he informed me that the lights flashing indicate the low point of the coach and that if you perform a zero point calibration you will correct that. In the service manual you will need to follow the instructions…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Answer 9

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 10

While I have no way to see exactly what leveling system you have on your 2006 Tiffin Phaeton 35DH, I was able to find information on a forum showing someone who did confirm the SnapPad HiWay 10 Jack Pads for HWH and Atwood Leveling Systems w/…

view full answer...

Answer 11

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 12

If you have the Gooseneck versions of the Curt CrossWing ( #C92DR or #C32DR) you unfortunately would not be able to use the Rota-Flex with it. The pivoting head causing too much strain for the single point of contact you have with a gooseneck hitch.…

view full answer...

How Thick Are SnapPad Jack Pads

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching