Your truck is heavy duty enough that a weight distribution system is not as needed. Would it help to some extent? Sure, but for as big of a truck you have and for how light weight your RV you'll be just fine without a WD system. Also, they do not make aluminum or lighterweight options either.
Some suspension enhancement like the SumoSpring kit part # SSR-312-54 would give you additional support to get rid of any possible sag as well as improve handling so that would be one solution that... view full answer...
If you have the Westin HDX Grille Guard part # 57-3545 which is a fit for a 2014 Ram 1500 then the correct Replacement Hardware Kit for Westin HDX Grille Guards is part # 57-354PK. view full answer...
For a replacement axle I recommend the Dexter Trailer Axle Beam with 4" Drop E-Z Lube Spindles - 95" Long - 7,000 lbs # 8327860. I'm assuming by "4 inch" you meant a 4" drop since 7k axles have a diameter of 3". This axle will be the same as your current axle with the exception of the spring-center-to-spring-center length which is 79-1/4".
The spring center measurement not matching up is fairly common but there is a solution. You will need to have the spring seats cut off of the axle... view full answer...
You will need the Rear Header # TX5469-RearHeader for the Truxedo Lo Pro Tonneau # TX546901 on your 2018 Ram 1500 with the 6-1/2' bed. The Rear Header # TX578101-REARHEADER you found fits the following vehicles with a Tonneau Cover # TX578101.
2004 - 2007 Ford F-150 6-1/2 Foot Bed - excluding Stepside
2008 - 2008 Ford F-150 6-1/2 Foot Standard Bed - without Bed Cargo Management System
2007 - 2008 Lincoln Mark LT 6-1/2 Foot Bed - with Trac System
2007 - 2008 Lincoln Mark LT 6-1/2 Foot... view full answer...
Sounds like you are looking for replacement barrel clips for the Westin Signature nerf bars # 25-3290 that you referenced which we offer with the part # 60-0244. These are the clips that attach the step pad to the bar. view full answer...
Trailer makers do not maintain specific details about the items like fenders that are installed on their trailer products but we do carry a wide range. I did find photos of the Livin Lite Quicksilver 6.0 pop-up camper trailer and it does appear to use a black plastic fender much like # F008582. This fender has top and side steps and works for 12-inch rims/wheels.
The linked page will display all trailer fenders we offer. Click on your wheel size to then see compatible fenders. (If you... view full answer...
The bolts that come with the Pro Series Coupler part # PSA200S0303 are the part # PS024202 which are 5 inches long and 5/8 inch diameter. view full answer...
The Tri-Glide has been discontinued. It was replaced by the Flex Air line. The Flex Air pin box that will fit your Lippert 1621 pin box is # LC328492 but it is rated for 18,000 pounds and not 21,000. There is a TrailAir version that is rated for 21,000 pounds that will also fit. It is # LC158778.
So far, people seem to like the TrailAir model over the Flex Air model and if you are looking to match the capacity of the old pin box, which I recommend, I would go with the TrailAir model, #... view full answer...
I contacted the manufacturer regarding this issue. Per the manufacturer those parts are not replaceable and their recommendation given the parts you needed is to replace the whole 5th wheel rail adapter because they suspect there could be further damage.
The correct replacement is the Reese 5th Wheel Rail Adapter for Ram OEM 5th Wheel Towing Prep Package - 25,000 lbs # RP30154. view full answer...
I have a solution for you. I called my contact at Lippert and he confirmed that the only replacement parts that are available for purchase for your 69" Solera awning is the the pitch arm (the bottom inside arm) or the gas strut (the little hinge-like piece that connects the inner top arm and the pitch arm). With that being said, you will need a completely new arm assembly if you need the inner drive arm (the top inside arm). The reason for this is because Lippert uses a special machine... view full answer...
The correct motor to replace your Venture Landing Gear 5th Wheel motor, model 1-065-041012-01 is the Lippert Components Tuson High Speed Motor # LC141893, which has the same 7,140 RPM speed as your existing one. The correct gearbox to go along with it is part # LG-179015. view full answer...
The Replacement Mounting Hardware Kit for Westin HDX Nerf Bars with Drop Steps # 56-135PK that you mentioned is actually meant to fit the Westin HDX Nerf Bars with Drop Steps # 56-13555 & the Westin HDX Nerf Bars with Drop Steps # 56-135552 and is not a fit for your 56-14095 HDX step bars.
Instead, take a look at the:
- Replacement Installation Mounting Hardware for Westin HDX Nerf Bars # W34HR.
I did also call and verify with Westin that this is the correct kit. This kit includes all... view full answer...
The Jet Nozzle # 278-SS04 is a replacement for the SewerSolution Macerator System # SS01. So if you have this system and need to replace the Jet Nozzle then this is the part for you. If you are looking to add the system then # SS01 is what you would need.
In addition to the Jet Nozzle other replacement parts for this system are:
Quick Connect Hose Assembly # SS05
10 Foot Extension Hose # 278-SS02
Replacement 4-in-1 Elbow Adapter # SS06
Maintenance Kit for 2017 and newer systems # SS07 view full answer...
You do not need to replace your Fastway e2 Weight Distribution # FA92-00-0800. As you suspected, a new shank is all it will take to get you going again. Fastway doesn't have one for a 2-1/2" receiver, but Equal-i-zer who makes Fastway does. We have the following options available:
-Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 7" Rise, 3" Drop # EQ90-02-4700
-Equal-i-zer Weight Dist Shank - 2-1/2" Hitch - 8" Rise, 4" Drop # EQ90-02-4800
-Equal-i-zer Weight Dist Shank - 2-1/2" Hitch... view full answer...
We do indeed offer a replacement base for the B&W Companion 5th wheel hitch that are compatible with the Ram OEM puck system, part # BWRVB3600 for the long bed or the # BWRVB3670 slider for short bed trucks.
You can see current pricing by using the provide link to the product description page. view full answer...
To replace the hardware that comes with the Curt Trailer Hitch Receiver # C13419 for your 2023 Ram 1500 we have the part # RHK but this includes all of the hardware.
Unfortunately we don't have individual hardware parts for any of the trailer hitches that we carry - just the entire set of hardware. view full answer...
The Replacement Hardware kit # 21-240PK that you referenced is actually replacement hardware for Nerf Bars # 21-24010 and # 21-24015 which fits 2015 - 2019 GMC Canyon Crew Cab and 2015 - 2019 Chevrolet Colorado Crew Cab pickups.
For your 2019 Ram 1500 you would need Replacement Hardware Kit # 21-2408PK which is for the Westin PRO TRAXX Oval Nerf Bars # 21-24080 and # 21-24085.
If you happen to have a 2019 Ram 1500 Classic then the correct Replacement Hardware is part # 21-2356PK which... view full answer...
Yes, your OEM 5th Wheel Hitch Legs # C16021 will allow for the following replacement hitch heads which includes the A25 head.
E16 # C16515
A16 # C16520
A25 # C16580
Q20 # C16530
Q24 # C16545 view full answer...
You are looking for the Replacement Side Rails # RTX45FR for your RetraxPRO XR Hard Tonneau Cover # RTT-80233 that you have on your 2018 Ram 2500 long bed. view full answer...