We have a variety of side mount trailer jacks, however, all of which are manual crank. The only electric jacks available are for a-frame trailers. Although we do not have an electric jack that attaches to the side of the trailer frame, we do however have several options with a drop leg feature that will eliminate the need for strenuous cranking.
I recommend using the Dutton-Lainson Bolt-On, Drop Leg Trailer Jack part # DL22320 as this has the drop leg feature that will minimize the amount... view full answer...
Since your 2015 Lincoln MKC didn't come with the factory tow package you need the Tekonsha T-One # 118284 for the basic trailer light functions. Then typically when a boat trailer has a 5-Way wiring harness that means it has a hydraulic actuator with an electric lockout. If this is the case then all you need to complete your wiring is the Tow Ready # 20036. This plugs into your 4-Way and then includes an extra wire that you connect to your reverse wire.
If you still wanted to install a... view full answer...
If your 2013 Lincoln Navigator came equipped with a factory 7-way connector, you will not need to do any wiring at the back of the vehicle. The only thing you will need to do is to mount the brake controller, connect to the tow package port which is located under or behind the dash, and you are ready to go.
If by chance your vehicle only came with the factory 4-way, the installation of a 4 pole to 7 pole adapter, # 37185, will be needed. To make the connections for the brake and 12V power,... view full answer...
When it comes to using a weight distribution system on your 2010 Lincoln Navigator The Fastway e2 Weight Distribution w/ 2-Point Sway Control - Trunnion - 8,000 pounds GTW, 800 pounds TW # FA92-00-0800 will be the system that you will need. Using the Fastway e2 will not cause the Navigator to pop up if you're under the towing capacity limitations for your vehicle, even though you have the heavy duty tow package doesn't mean the vehicle can actually handle it.
When using a weight distribution... view full answer...
For your 2022 Lincoln Nautilus, we have the:
-WeatherTech Front Auto Floor Mats # WT59HR for the front,
And the,
-WeatherTech 2nd Row Rear Auto Floor Mat # WT39HR for the back.
These floor mats are grey in color, is custom fit to match your vehicle, and due to the advanced surfacing this mat has, it will create channels that divert fluid and debris away from your shoes and clothing.
If you want to take it a step further, I also recommend getting some Cleaner and Protector Kit for... view full answer...
Yes, we do have those kits.
The kit 6212 that you referenced is part # SM99666 on our site.
The kit 6237 that you referenced is a combination of parts # SM99226 and # SM99625 on our site. view full answer...
Yes we do!
For the Malone MicroSport Trailer for 2 Heavy Kayaks # MPG461B2, take a look at the:
-Fulton Bolt-Thru Swivel Marine Jack w/ Caster # F77CR.
This jack will work great with your MicroSport trailer, has a heavier duty powder coat to protect the jack from rust and keep the paint fresh, and also has a nice swing up feature that makes this easy to stow when not in use.
Additionally, this jack also has a lift capacity of 1,200lbs, and a maximum lift height of 10".
Attached is... view full answer...
For your 1999 Lincoln Navigator, I recommend taking a look at the:
-Curt Trailer Hitch Receiver # C13049.
This trailer hitch has a maximum towing capacity of 6,000lbs, and a maximum tongue weight capacity of 600lbs, however I recommend taking a look at your owner's manual for your vehicle's maximum towing capacities, and ensure you're utilizing the lowest number between the hitch and vehicle.
Additionally, for a complete towing setup you're going to need wiring # C55344, and a ball... view full answer...
I can definitely help you out with that. In addition to the tow bar, brakes and lights, you will also need a base plate kit and safety cables. I have listed these parts out for you below, along with a brief description of their purpose.
Base Plate Kit: This is a custom fit part that provides the attachment point for the tow bar on your MKZ Hybrid.
- Blue Ox Base Plate Kit # BX2674
Tow Bar: This is what will come from the motor home and attach to the base plate kit.
- Blue Ox Alpha 2... view full answer...
I took a look at the owner's manual for the 2017 Lincoln MKX and found out yes, it can be flat towed (you will want to refer to the page on "Recreational Towing" in the manual to ensure you follow the necessary procedures).
There are a number of parts you're going to need in order to do this, starting with compatible base plates. I recommend the Blue Ox # BX2673. For a tow bar I recommend going with the Blue Ox Alpha # BX7380 because of how easy the tow bar is to connect to the base plates... view full answer...
The Curt Trailer Hitch Receiver # C13067 is confirmed to fit your 2008 Lincoln MKX. This class III receiver is rated for up to 400lbs of tongue weight and a trailer up to 4,000lbs. Be sure to verify your maximum trailer capabilities with your Lincoln dealer and do not exceed the lower of the limits.
You will need the Curt T-Connector Vehicle Wiring Harness # C56329 for your MKX, as the # C55326 you found fits older Ford cars and not your MKX. The Harness # C56329 will give you a 4-way... view full answer...
When it comes to installing the tow bar wiring on your 2017 Lincoln MKZ The Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 7-Wire to 6-Wire Straight Cord # RM-152-98146-7 is the correct kit you would need. This kit is for a RV with a 7 round adapter and will make the Lincoln MKZ mirror the turn, stop and tail lights of the motor home.
If your motorhome has a 4 flat connector you would need The Roadmaster Universal Hy-Power Diode Wiring Kit # RM-154.
The # C56258 is used... view full answer...
What you will need in order to add a 7-Way to your 2011 Lincoln Navigator is the Adapter 4 Pole to 7 Pole and 4 Pole, # 37185. The # 118243 harness is actually for Ford Super Duty trucks. In order to install the adapter on your Navigator you will first plug the 4-Way you have into the back of the adapter. That will leave just 4 wires to hardwire to the vehicle.
The white wire will need to be grounded to the frame of the vehicle. Yellow goes to the reverse light wire behind one of the tail... view full answer...
You're going to want the Demco SBS Reinstall Kit # SM6270 for the Demco Stay-IN-Play Duo # DM86VR, You can remove the main components to your 2020 Lincoln Nautilus, from your 2012 Jeep Wrangler, and purchase the reinstall kit and be ready to roll. The components you're going to need to transfer from your Jeep is the operating unit, GeForce controller, and the actuating cylinder that is attached to your brake pedal. view full answer...
The Malone MicroSport Trailer for 2 Heavy Kayaks # MPG461B2 already comes with the lockable mounting brackets and a spare tire, the only thing that is sold separate is the lock for the spare.
You can us any lock the two brackets together, however I recommend taking a look at the BOLT Covered Padlock # BL7018519.
This padlock will code to the center cut key on your 2015 Lincoln Navigator so you do not have to worry about carrying around a bunch of different keys, and will do an excellent... view full answer...
To get a new set of hardware for your Draw-Tite Max-E-Loader Trailer Hitch Receiver item # 41116 you will want the Replacement Hardware Kit item # RHK. You will go to the product page and input the hitch item number 41116 and select Draw-Tite from the manufacturer drop down and this will give you all of the bolts and other hardware you need to complete your install.
We do not have part number 01130-712 in our system. view full answer...
When we installed the Curt Class III hitch, part # C13194 on a Lincoln MKC, we found that the inside top edge of the receiver sat 12-1/2 inches above the ground. The the bottom edge of your boat trailer sits at 16 inches with the trailer level, you'll want to use a ball mount with a rise to raise the trailer ball by about 4 inches. That way, once the trailer is hitches up, the rear of the vehicle will squat a bit which will place the trailer very close to level.
I'd recommend the Curt... view full answer...
You could make an adapter to go from the connector on your Aviator, if it is a factory 7-Way connector, to the 5 wires on your trailer. I would use the Pollak Black Plastic, 7-Pole, RV-Style Trailer Connector, item # PK12706, along with the 5-Flat Vehicle End 5-foot Wiring Harness, item # HM37908, to build an adapter. Once the adapter is built and wired, I would use the 5-Flat Trailer End 48-inch Harness, item # 20017, to splice to the trailer wiring.
If you have a 4-Way connector at the... view full answer...
The Blue Ox base plate kit that you will need to use is part # BX2673 for your 2017 Lincoln MKX EcoBoost with Adaptive Cruise Control. If you don't already have a tow bar and safety cables then I highly recommend the Blue Ox Alpha Tow Bar # BX7380which comes with safety cables rated for 6,500 lbs.
For a supplemental braking system the Air Force One # SM99243 is the best for you since your 2013 Tiffin Phaeton has air brakes. You will also need to use the Relay # RM-88400 unless you plan... view full answer...
I recommend the # C59496 wiring harness for your Corsair. This is a hardwired harness, as there isn't a plug and play option for your vehicle.
If you'd prefer an option that wouldn't require any cutting or splicing, I'd recommend the Tekonsha ZCI, part # 119250KIT. I've also linked to an install video, but once again it shows the harness being installed on a different vehicle. A circuit tester like # PTW2993 would be helpful for locating which wire carries which taillight function. If... view full answer...
Go To Results