Great question, Adrian!
For your 2005 Ford E-350 set up as a passenger van bus you will need to have a heavy duty universal hitch installed like the Curt # C99CR. This type of hitch installs by welding so you'll need to have a shop or certified welder help you plan out the installation.
If you don't already have a shop you plan on working with we have an installer locator I'm linking to this page for you to reference and see who is in your area to help you with the isntallation. view full answer...
Installation of both the B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1394 for your 2002 Ram 2500 and # BWGNRK1308 for your 2009 Ram 3500 Mega Cab short bed will not require the bed to be lifted or disconnected in any way. The instructions for both do mention a lifting device is recommended but this is only for holding the center hitch section under the bed while you bolt it up to the cross rails.
I recommend getting a Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring... view full answer...
Per Curt their Trailer Hitch Receiver # C13272 will not fit the F-Sport package on your 2017 Lexus RX 350. While we have had a number of reviews come back to us saying they were able to bolt it right up without issue there are other issues some have ran into where it would not fit their particular vehicle. The best I can say is you can see the installation video I have linked near the bottom of the page. If you see our particular Lexus has any components in the way of where the receiver... view full answer...
I have a couple options for you since I do not know what you already have on your 2024 Nissan Frontier.
First if you already have the factory tow package with a connector like the # HM40975 built into the bumper you can simply use the Wiring Harness # C55384 which will tee in line behind the connector.
If you already have a single 4-way flat connector, you could simply splice in a 2nd Connector # 118001. This particular harness has 48" long wires allowing you to place it somewhere else... view full answer...
AAMCO most likely disconnected it when they did work on your vehicle since most vehicles require disconnected the battery before doing so so my guess would be that they forgot to reconnect it at the battery upon completion of the work so you should check there. Also make sure the wiring connections at the battery are made tightly. view full answer...
While there is some variances in how the Go Power Solar panel kit part # 34282185 installs depending on the setup the diagram I found in the install instructions only shows a fuse between the controller and the battery so that would be what you would want to do. This matches the install video you mentioned as well. view full answer...
Hey John thanks for stopping by, yes the Redarc Tow-Pro Elite Brake Controller for Tekonsha Harness # RED63RR you were looking at does come with instructions, but we unfortunately haven't had a chance to shoot a video for a 2022 Subaru Accent.
Fortunately for you though, since you have the factory tow package Redarc has a super simple plug-and-play adapter # 3062-P that you can use. You'll just plug one end of the adapter into your brake controller, and the other end into the built-in... view full answer...
There is no specific plug under your bumper but we do have a plug and play wiring option for your 2024 Subaru Impreza RS. It looks like the RS is a hatchback so the correct wiring harness is the # 118744. If it was a sedan model you would need the # 118629 instead. Both of these plug into the connection points behind the rear taillights so no splicing is required. Tekonsha recently confirmed these fit the 2024 model so until we update our site you can ignore the warning that says "Not confirmed... view full answer...
You will need to add a 7-way to install the # 39523 (80500) on the 2012 GMC Canyon. If the 4-way at the back is plugged into a round US Car connector behind the bumper you can add a 7-way using the # HM40975. If it is an aftermarket 4-way, or attached using a different connector, you will have to add a 7-way using the # ETBC7.
Since it is a hardwire installation you will also want the Pigtail Wiring Harness for Tekonsha and Draw-Tite Brake Controllers - 34" Long # 7894. This will plug... view full answer...
Hey Woody we can definitely help with that. You will find the manufacturer instructions for the Curt # C11563 trailer hitch linked below. I have also included links to a few of our install videos. We have installed this hitch on a 2018 and 2020 Nissan Kicks. Installation on a 2019 model will be virtually identical. You can feel free to reach out to me if you have any further questions. view full answer...
Nope, you do not have to do any bumper fascia trimming on your 1997 Chevy Suburban to install the Curt Front Mount Hitch # 31042.
You don't have to do any drilling, either so it's just a bolt-on installation. As for clearance, from the top of the brackets to the bottom of the tube it is 4 inches. view full answer...
The battery type doesn't matter in this situation as you could still face this issue with two AGM batteries. If you're vehicle is running the alternator should be charging the start battery more than the draw from the 7-way 12v accessory pin. As long as the alternator is properly functioning you shouldn't have an issue charging both batteries while driving.
If the vehicle is off and the 7-way isn't tied to the ignition for power then you run the risk of draining the start battery if you're... view full answer...
The Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover w/ Contractor Rig Rack # FEF6985-CR4008 would block the bedrail lip so you'd have to mount any side toolboxes either to the rack or make your own t-slot bolts to mount the toolboxes into the track of the cover's rails. view full answer...
The 5" # FOS05TASF and 7" # FOS07TASF monitor Furrion Vision S Camera Systems can pair with up to four cameras at a time. The 4.3" monitor version # FOS43TASF is only capable of just one camera connection. You wouldn't be able to add a second set of side marker cameras and but would be able to add another rear camera # FCN48TASF, which most people either mount above the door of the trailer as a security feature or on the nose of the trailer to assist with coupling. view full answer...
Yes, you are able to switch to the 2" Ball # A-90 on the Curt TruTrack 2P Trailer Mounted Weight Distribution System # C67ZV. As Curt does not offer the hitch with a 2" ball you will have to change it out yourself or have it done at the shop which installs the hitch for you. view full answer...
The SmartPlug RV TV/Internet Inlet # SM28VR is the closest option we offer to the BDCOAXECPB. This comes with a coaxial connector and blank port for you to install an ethernet port from your local electronics/electrical supply store into. view full answer...
I would not recommend installing a Diode # RM-690 on the brake line as this is a part which can fail and if it were to you could risk doing a lot of damage. While the Bright Way Push-to-Test ICU Trailer Breakaway Kit # BW94FR could risk damage to your brake controller the breakaway cord should only ever be pulled when the trailer becomes disconnected from your tow vehicle or during testing which you should not be connected during either. If you are connected electronically to the trailer... view full answer...
To answer your question Mark, both ways are correct. The vehicles frame, or the negative battery terminal are both suitable locations for a ground. It could be the installer in that particular video just preferred to do it that way since the battery was so close. The Manufacturer instructions for the Tekonsha T-One Vehicle Wiring Harness # 118683 do say to find a grounding point near the connector such as the frame or the crossmember. It is always a good idea to stick with what the manufacturer... view full answer...
We cannot recommend using a single tire chain like the Titan Chain # TC1138 (or any single tire chain) on all four rear tires of a dually. If you want chains on all four rear tires, you will need to use a dually tire chain such as the Pewag Dually Tire Chains # PWE4216SC which are made for the 195/75R16 tires.
As far as installation, the # TC1138 and the # PWE4216SC are both drive-over chains, so installation would be fairly similar. You will need to lay out the chains on the ground,... view full answer...
Go To Results