A bolt-on axle over-under kit like # K71-384-00 and # K71-385-00 will typically give your trailer between 4 and 5-inches of lift. The exact amount of lift depends on the axle diameter and the height of the leaf spring stack. Lift will be the sum of the axle diameter plus the height of the spring stack. Kit # K71-385-00 works for axles with 3-inch diameter
Installing an axle over-under lift kit on a trailer is not a complex job but it does require the right safety equipment to avoid risk... view full answer...
You do need a crossbar to mount a SnowBear plow on your 2013 Ford F-150 but it's not included with the bracket kit # SB397-105. If you need the crossmember itself use part # SB324-060.
The plows that work with that bracket kit are:
# SB324-116 which is 88 by 26 inches
# SB324-167 which is 54 by 22 inches
# SB324-166 which is 82 by 19 inches view full answer...
Since you already have the 4-way trailer connector on your 2008 Ford F-150 you may only need an adapter, part # 37185. This converts the existing 4-way to a 4- and 7-way connector in one. It plugs into your 4-way and then the other wires need to be connected into the truck's wiring.
Some models of the F-150 already have the wiring for the trailer brake output circuit and the 12 volt power lead ran from under the hood to the end of the driver's side frame rail. If you can find these... view full answer...
We can get your 2014 Hyundai Tucson ready for towing your 2009 Aliner Alite compact camping trailer. Since you already have the 1-1/4-inch Class II hitch you will need a ball mount, hitch ball, wiring and perhaps some towing mirrors to complete your setup.
Based on my research the single-axle Alite does not have trailer brakes (since it has a dry weight of only a few hundred pounds it does not have to have them) so you should not need a brake controller. If it does have brakes then I... view full answer...
I do have a solution for you, but using an extender with a high-low adapter would be using 2 adapters and is not advisable. Hitch extenders reduce the weight rating of your hitch by 50% and will also cause more movement not to mention the torque that will be on both adapters when you are making a turn.
Instead what you can do is swap out your current hitch mount tow bar, like the Blue Ox Alpha # BX7380 for a coupler mount tow bar like the Blue Ox Acclaim # BX4330. This allows you to then... view full answer...
To connect the Blue Ox Alpha tow bar with the Roadmaster EZ base plate kit, part # 521877-1, on your Mini use the Roadmaster # RM-032 adapter.
It comes with the pins that run through the tangs to connect the tow bar to it. You probalby already have the pins with your tow bar but maybe not. view full answer...
Thank you for the information and photos!
Normally we recommend using an over-under kit to move your axles from above your leaf springs to under them, but since your axles are already in this position you can either use the 2-1/4" Lift Kit # RR23QX or you'll have to replace your current hangers with tall ones to get your rig sitting any higher. You ultimately should be okay being out of level by 3" - 4" but anything more than that would cause issues.
I would just go with the lift kit... view full answer...
The Dexter Trailer Springs Over-Under Kit # K71-385-00 is a good start and should give you a good start on getting your trailer sufficiently above the bed rails on your new F-250. In order to get an additional 2" or so clearance I recommend using the Tandem Axle Lift Kit # RR23QX, which will extend the spring hangers on your leaf spring suspension to create the additional clearance you're seeking.
The other thing to consider to make sure that you're not sacrificing any ride quality would... view full answer...
To charge your batteries from an AC power source is pretty simple, you just need a charger like the CTEK US 0.8 Universal Battery Charger with Pulse Maintenance # CTEK56865. This is designed for smaller battery banks and just plugs in using a standard outlet like what you find in your home.
To effectively charge your battery from your 2017 Ford F-250 is a little bit of a different story. A common misconception is that running a power wire from the vehicle battery to the trailer battery... view full answer...
The correct Reese Sidewinder for your 2021 Genesis Supreme 5th Wheel will depend on the model of pinbox that's currently on it; you can find the model of the pin box on the spec sticker that's usually somewhere on the face or side of the unit. Unfortunately, there's not a way for us to tell exactly what pin box is used on a particular coach.
The 5th Airborne Premium 5th Wheel Air Ride King Pin w/ Sidewinder and Turret - 16,000 lbs # RP61452 is designed to replace the following pin boxes:
Venture... view full answer...
We have exactly what you need with part # HM42137.
It plugs inline with your 2007 Dodge Ram's factory 7-way so you keep the original connector and can add thi one into your truck's bed to hook up your gooseneck trailer. view full answer...
If you are wanting to carry your dirt bike with the 2013 Toyota RAV4 that you input into the vehicle information section then I recommend using the etrailer Trailer Hitch Receiver # e98864 which has a tongue weight (TW) rating of 525 lbs.
You could then use the etrailer Motorcycle Carrier # 98873 which is compatible with this trailer hitch and has a weight rating of 500 lbs. If you don't already have tie-downs then I recommend using the Erickson Ratchet Tie-Down Straps # EM31353.
I do... view full answer...
In order to carry a bike rack on the back of your Taxa Cricket travel trailer with 40" between the frame members you can use the Curt Adjustable Trailer Hitch # C13701 which will fit on trailer frames between 18" and 51" wide. This hitch has a 2" drop on the receiver to allow you to clear the rear bumper and can be either bolted or welded onto the frame of your trailer. Because of the size and type of trailer, you may want to reach out to the manufacturer to determine whether or not the... view full answer...
You're almost there. You also want that circuit to be protected so you also need a circuit breaker.
I recommend using our # ETBC7L kit because it includes everything you need. You said you have an adapter already. If your has the wirng already you can connect it's 12 volt circuit wire to your battery through a breaker. In this case use part # 10-1-1 and a circuit breaker # 9510. view full answer...
So long as your 2003 Crownline currently has hydraulic disc brakes, you can absolutely add the HydraStar Vented Marine Electric Over Hydraulic Actuator for Disc Brakes # HS481-8067.
It will do a great job of giving you the stopping power needed so your boat doesn't get pulled down the ramp, and since you have surge brakes and brake lines already, there's only a couple of other things you'll need, starting with a breakaway kit, the Hopkins Engager Push-To-Test Trailer Breakaway Kit with... view full answer...
If I'm understanding you correctly the answer is yes you can.
Your Explorer has a Class III trailer hitch receiver that measures 2 inches on the inside. This means it must have a Class III ball mount that fits into it to tow a trailer, like part # C45030. I've linked all of our ball mounts that'll fit to this page.
On the other side the trailer has a coupler that fits onto the hitch ball. With a trailer that small it's probably a 1-7/8 inch ball. It could be a 2 inch or even a 50 millimeter... view full answer...
Although we don't have any specific trailer hitches for your 2000 Four Winds International Hurricane Motorhome we do have a selection of weld-on heavy duty trailer hitches that you can filter through.
An example would be the Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube # 41990 with the 7" # 4907 or 16" # 4916 brackets. This would be a custom job performed by a professional welder so it would be beneficial to consult them as well to see what would work for the installation.
Our... view full answer...
The large port on your Extend a Stay, basically part # CAM59113, is a male 1 - 20 disposable cylinder connection.
To hook your BBQ grille up using that fitting you can use part # 204132-MBS which is an adapter to a Type 1 fitting. Then use a Type 1 hose with a regulator, like part # CAM57721, that's 12 feet long and has a 3/8 female flare to connect to the grill.
If these parts don't have the correct fittings let me know. view full answer...
We do have a few electric A-frame jacks with a 2 inch diameter outer tube:
Stromberg Carlson # JET-2500 rated for 2,500 pounds.
Ultra-Fab # UF38-944017 rated for 3,500 pounds.
Ultra-Fab # UF38-944037 rated for 3,500 pounds. This jack also includes a 7-way trailer connector
Ultra-Fab # UF38-944016 rated for 4,000 pounds.
Each jack offers 18 inches of lift. I've also attached videos of each one for you. view full answer...
We do have a solution for you that plugs into the square plug on the rear of your 2006 Ford F-250 but it will require 2 piece to get you to a 7-Way and 4-Way combine connector.
Start off by installing the Hopkins Connector # HM40165. This has a 4-Way connector and a loose blue wire as well as a loose red wire.
The next step is to install the Hopkins Adapter # 37185 which has a 7-Way and a 4-Way connector. The 4-Way on the adapter will connect to the 4-Way on the 40165 and then you simply... view full answer...
Go To Results