The Buyers Products Fabricators Hitch Plates like part # 3371809042 are not given a weight capacity by the manufacturer. This is because the weight capacity will largely be dependent on how securely it is mounted. The highest rated pintle hook we offer for this is the Buyers Pintle Hook with Mounting Kit part # 33710042 which is rated for up to 40,000 lbs so the above plate will handle this so long as it is attached correctly. view full answer...
While the Buyers Products Fabricators Hitch Plate # 3371809027A does not carry a weight rating, their custom fit hitch plates are only rated for 20,000lbs. Since this is a fabrication kit you will be able to add more steel and additional mounting points to increase the hitch strength and be able to bolt on the Buyers Products 30 Ton Pintle Hook # 337PH30. I recommend having the plate fabricated and strengthened at a shop experienced in this work. view full answer...
The Tow Ready 18-Inch Combo Bar # 80818 does not carry specific tongue weight or towing weight ratings since it is a fabrication part that will be used with other materials to construct a hitch. This is not a hitch extension like # C45796 or the others shown on the linked page.
The actual capacity of this item depends on how it is installed, the capacity of the other components used to install it and on the capacity of the vehicle on which it is mounted.
In an optimal installation the... view full answer...
I have spoken with Buyers Products in the past about the Buyers Products Fabricators Hitch Plate part # 3371809043 and they have stated that the reason that they do not rate the plate for a specific weight capacity is becuase this will largely be dependent on how securely it is mounted. The highest rated pintle hook we offer for this is the Buyers Pintle Hook with Mounting Kit part # 33710042 which is rated for up to 40,000 lbs so the above plate will handle this so long as it is attached... view full answer...
Fabrication parts like Curt Combo Bar # E-9 do not carry a weight capacity rating because that will largely depend on the nature of the installation chosen. To what you weld it and how well you weld it will determine its ultimate capacity. If installed properly it will have enough capacity for any recovery winch intended for use in a 2-inch hitch. view full answer...
The hole spacing of the Buyers Products Fabricators Hitch Plate # 3371809042 that you referenced is the same as the standard pintle mount bolt pattern which is 1-3/4 inches apart vertically and 3-1/2 inches apart horizontally. view full answer...
I had the Buyers Products 2-5/16" Fabricators Flatbed Gooseneck Hitch # 3375613500 measured and have a picture with all measurements included. This is indeed rectangular and is typically installed with the longer sides going across the bed area. This allows for easier access to the ball release lever. view full answer...
The plates on the Curt Weld-On 2" Receiver for Custom Fabricated Hitches # E17 are 1/4" thick. The receiver tube is 2-1/2" wide, or 3" if you count the collar at the opening. For a tube size, I would discuss that with the fabricator or welder that will install it. You will need something that can handle the weight you plan to tow/carry and that will fit in the correct spot for installation. view full answer...
The Replacement 18'1" Fabric for 19' RV Awning item # LCV000334424 you were looking at is made for Solera, Dometic A&E, or Carefree RV awnings. It is for a 19' awning assembly and measures 18'1" x 8'.
In order to determine if this is the correct replacement fabric for your 2009 Salem camper trailer you're going to need to determine what brand of awning you have. There should be markings or part numbers stamped or stickered somewhere. I do not have any way of knowing what's on your camper.
If... view full answer...
The actual width of the fabric/canvas on the Solera Slide-Topper Awnings will be right at the max box width range. The max box width range for the Solera Slide-Topper Awning part # LCV000165062 for black or part # LCV000163287 is 85-3/4" therefore, the actual width of the canvas is going to be around 85". view full answer...
The wheel covers like the part # CAM45333 that you referenced do have a soft fabric lining that will help protect the wheels from any surface scratching.
Check out the review video I attached for more info as well. view full answer...
Curt will not release the specific information about how they build their Trailer Hitch Receiver # 11164 as it would allow anyone to attempt to fabricate their own receiver rather then buy theirs or go through their own fabrication and testing. Curt has tested this receiver to be strong enough when installed properly to support up to 200lbs of tongue weight and 2,000lbs of trailer weight on your 2006 Audi A4. Be sure not to exceed any of the manufacturer specifications from Audi for towing... view full answer...
Looking at the owners manual for your 2011 Volvo V50 it says the maximum recommended tongue load for any receiver is 165lbs. As this is even less than the Curt # C11438 is rated this would explain why there is only a class I receiver available. Curt does have a note "***DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY.***" as well in their instruction manual linked below.
If you still want to find another option you should contact a fabrication shop in your area so they... view full answer...
I spoke with my contact at Tow Ready about the Tow Ready Combo Bar, part # 80948.
This is a 48 inch long bar that is used to fabricate 2 inch trailer hitch receivers. They told me this bar is used when they manufacture hitches with capacities up to 12,000 lbs so it should work great for you and the trailer you mentioned.
This bar has a raw finish and can be welded. view full answer...
I have a solution but there are no custom fit front mount hitches available for the 2020 Ford E-350 chassis. Instead the only option would be to use a universal receiver like item # 41990-16 and have a local fabrication shop fit it to the frame of your RV. view full answer...
Glad to hear that you like the 36" covers!
I went out to the warehouse and found the opening of the fabric part to the CE Smith Padded Covers # CE27901 is about a 3" diameter. view full answer...
I had our warehouse measure each of the front mount trailer hitch receivers you mentioned, and the dimensions are as follows.
The Curt # 31408 measures 32-3/4" long x 8-3/4" wide, the Draw-Tite # 65080 measures 36-3/4" long x 10-3/4" wide, and the Draw-Tite # 65079 measures 31-3/4" long x 9-1/2" wide, which you can see in the included diagrams.
Each of these options will require fabrication as you know, since none of them are confirmed to fit your 2002 Kia Sportage 4x4. I recommend checking... view full answer...
The Curt Solid Steel 2" Hitch Bar # D31 that you referenced is designed for someone who wanted to fabricate their own hitch mounted accessory. It's not a hitch extender so it would not reduce hitch capacity like a hitch extender would.
I attached an FAQ on hitch extender/adapters for you to check out as well. view full answer...
The EcoHitch Stealth Trailer Hitch Receiver # 306-X7365 you were looking at for a 2023 Subaru Crosstrek does have a 2" square opening. The corners are rounded and not a sharp edge allowing you to use Class III 2" accessories and ball mounts. We do sell a 24" Hitch Bar # D36 which will fit inside the tube if you are trying to fabricate your own hitch mounted accessories. view full answer...