To add a 7-way to your 2018 Dodge Durango without a factory towing package you'll need a couple parts. The first is a 4-way, the T-One Vehicle Wiring Harness # 118617.
After that you will need the Universal Installation Kit for Trailer Brake Controller # ETBC7, which will give you the 7-way connector (which plugs into the 4-way), circuit breakers and the rest of the hardware needed for a functioning 7-way. I have added links to video reviews and installs of these parts for you to check... view full answer...
We've got just the parts you're looking for. You'll want to start with the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118617, which will easily install by teeing into the tail lights on your 2021 Dodge Durango and provide you with the base parts you'll need to add a 7 way.
Once you've installed the # 118617 you can install the # ETBC7, which will give you both a 4 way and 7 way trailer connector. The # ETBC7 comes with all of the wiring, breakers and connectors... view full answer...
Since sewage connectors do need a proper seal (typically by using solvent # A05-0303) I do recommend changing out some of your sewage pipes as they are looking a bit rough.
It does look like you have a 3" round pipe from your photo so if you were to keep your current system you could possibly use a Fernco rubber sleeve to connect the Valterra Coupling # F02-2025BK to either an extension or to the Valterra Bladex Waste Valve # T50. If you need an extension you will put this waste valve... view full answer...
My information shows that the maximum towing capacity of the 2001 Dodge Durango SLT 4wd with 4.7 liter V8 engine and 3.55 rear end gear ratio is 4,100 lbs. This means that if you were to tow a travel trailer with a dry weight of 3800 lbs you would only be able to add 300 lbs of gear to the trailer, including water, propane, trailer battery, and all of the other equipment you will need. You should check your specific vehicle max towing capacities in your owners manual or consult the vehicle... view full answer...
The only full Westin grille guard we carry for the 1999 Dodge Durango is part # 40-0145 and its replacement brackets are part # 40-014PK.
If instead you just have the Safari light bar, part # 30-0005-1085 or # 30-0000-1085 then instead use part # 30-1085 for the brackets.
If the guard you have doesn't appear to be any of these send me some pictures of it and I'll see if I can track down which model you have and its replacement brackets. view full answer...
I took a look at the 2022 Dodge Durango R/T owner's manual and it looks like the Mopar 82216418AA harness will be required for your electric power steering. This is something you will have to acquire from your local dealer. I recommend checking your manual or asking the dealer to verify this information. In addition to the Mopar harness you will need the following to flat tow your Durango:
Base Plate: Roadmaster Direct-Connect Base Plate Kit # RM26VR
Tow Bar: Roadmaster Nighthawk All... view full answer...
There are two ways to get your brake controller connected. You will want to use # TK93VR and plug it directly into your brake controller, then the other end will get connected to the factory prep connector under your dash on the driver side. If your brake controller just has three wires hardwired into the back of it, you can use the same # TK93VR harness and cut the Tekonsha plug off and hardwire it to your brake controller. view full answer...
To install the Redarc Tow-Pro Liberty Brake Controller # RED24FR on your 2024 Dodge Durango you simply need the Plug and Play Wiring Harness # RED77FR. This will allow you to easily plug all the components together so you are ready to tow your trailer with electric brakes. view full answer...
The left and right hand assemblies as a kit for 10 inch, self-adjusting brakes is # AKEBRK-35-SA. They'll need to be adjusted once at the initial install but that's it. They're also labeled left and right to make the install process easier.
To find the correct hub and drum assemblies with the bearing kit I'll need the inner and outer bearing numbers currently on your trailer. If you can respond back with them, as well as your bolt pattern, I'd be happy to find the correct parts. view full answer...
Since you are wanting to keep your full size spare installed on your 2017 Dodge Durango R/T the trailer hitch that you need to use is the Draw-Tite # 75713. This has a Tongue Weight (TW) rating of 900 lbs and a Gross Trailer Weight (GTW) rating of 6,000 lbs. When used with a weight distribution system the TW stays the same but the GTW jumps up to 7,500 lbs. You will need to consult your owner's manual regarding your max towing capacity as it is typically lower than what the trailer hitch... view full answer...
The Rhino-Rack Roof Rack, # RRVA126B-2 and # RRSX100, that you selected, will work great for your 2004 Dodge Durango. This rack has a weight capacity of 175 lbs, so it is capable of carrying most ladders. You should check the capacity of the Durango roof to be sure it is capable of carrying your ladder. view full answer...
Whether or not you'll be able to flat tow your 2018 Dodge Durango GT AWD will depend on the type of transfer case the vehicle is equipped with. If you've got the single speed transfer case, these models cannot be flat towed and must be towed with 4 wheels up on a dolly. A two speed transfer case is usually found in the V8 models of the Durango and will have 4H/4L settings available to use. If you've got the 2 speed transfer case, your vehicle can be flat towed. If you've got a V6, you've... view full answer...
To add a trailer brake controller to a 2006 Dodge Durango without the factory tow package you will need several parts. First you will need to install trailer wiring harness # 118390. I have included a link to a video and a link to the instructions showing how to install this harness.
After you install the 4-Way you will then need to install # ETBC7 which will provide the 7-Way and the wiring needed to install a brake controller. I have included a couple of links that will walk you through... view full answer...
The available wiring harness for your vehicle, item # 118390 connects inline with plugs behind the taillights and you will need to run a hot lead to the battery.
The power wire is needed to protect the vehicles sensitive circuitry. The trailer lights will be powered by the vehicle battery but will get the signals from the vehicle turn, brake and tail light functions. view full answer...
Yes, the Curt Echo Wireless Trailer Brake Controller item # C51180 is completely plug and play. All you need is a functional 7-way connector and a smart phone to utilize this brake controller. I have linked an installation video so you can see the ease of setting up and using the Curt Echo.
To get your 4-flat connector to a functional 7-way you will need the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires item # ETBC7L. The kit includes... view full answer...
In order to determine if you would need to install a Roadmaster Brake-Lite Relay Kit # RM-88400 with your Roadmaster Diode Kit # RM-154 you will need to follow the following guide:
Are you using a supplemental braking system that depresses the brake pedal in your towed car?
No - You do not need a brake light relay.
Yes - You may need a brake light relay. Continue on to the next question.
Do the brake lights on your towed car illuminate while the engine is off?
No - You do not need... view full answer...
When it comes to getting the replacement hardware for a Curt Front Mount Hitch for your 2002 Dodge Durango you will need The Replacement Hardware Kit for Trailer Hitches # RHK. When you bring up the #RHK there will be two boxes you will need to fill out. The first one you need to type 31080 and then on the second box there is a drop down arrow scroll down until you find Curt.
I attached a review video link below. view full answer...
To install a 7-way trailer connector on your 2007 Dodge Durango without a tow package you will first need to install a 4-pole harness, part # C55597, and then use our brake controller installation kit # ETBC7 to convert it to the 7-way format. The kit includes the 7-way socket plus all of the other items needed to provide a working 7-way with lighting and trailer brake signals, as well as 12V power.
I have linked the written instructions and a video for the Curt harness and an article... view full answer...
I have a solution for you, but there is not a package with all of these parts offered so you'll need to get the individual parts. I'm also skeptical that there is room to fit a 7 way trailer plug in the opening left by removing the knockout panel; the 4 way fits without issue, but you'll likely need to find a mounting location below the bumper for the 7 way connector because of its' size.
With that said, you can use the Draw-Tite # DT38MR and it will fit right behind the knockout panel,... view full answer...
Go To Results