Expert Answers about Chevrolet Silverado 1500
- Troubleshooting Overload Error Code with Prodigy P3 Brake Controller
- The OVERLOAD error message you are experiencing with your Prodigy P3 part # 90195 is caused by a high current draw from the brake circuit. In other words, there is a short somewhere in your brake output circuit. Typically the problem can be found at the trailer connector, on the brake output circuit on the trailer, or at the wiring connection at the brake magnets.
Start by examining the trailer connector on the trailer. Make sure that there is no damage or corrosion and that the wiring...
view full answer... - No Power to Brake Controller Using Factory GM Harness on a 2014 Chevy Silverado 1500
- The factory brake controller harness for your 2014 Chevy Silverado 1500 may not have the same wire colors for functions as the brake controller does. On the brake controller, white is ground, black is 12 volt power in, red is input from the brake switch, and blue is output to the trailer brakes.
You can test the factory harness by plugging it in and not attaching the brake controller. Then use a circuit tester such as # 3808 to test the wires on the factory harness. If none of them have...
view full answer... - Brake Controller Installed in 2021 Chevy Silverado Z71 Trail Boss Not Powering Up
- Assuming that you've found the correct connector for the # 3064-P brake control harness which is located under the dash to the left of the steering column, I'd wager than you have a fuse missing in the power distribution box in the engine compartment on the passenger side. Check fuse location # 84, and make sure that there's a fuse installed there. If the fuse is missing or blown, you can obtain a replacement from your local auto parts store.
view full answer... - Power Not Reaching Brake Controller Installed on 2016 Chevy Silverado
- If you're not showing any power at all on the Tekonsha Prodigy P3, # 90195, make sure you're using the correct brake controller wiring adapter, part # 3016. Use a circuit tester like # PTW2993 on the black wire of the harness to check if power is reaching the harness.
Once that's been checked, take a look at the fuse block under the hood. Make sure that there's a fuse in position number 1 and check it to ensure it hasn't blown.
The 2016 Silverado won't require completing any wring under...
view full answer... - What Does the Error Code A-09 Mean on my AirLift WirelessAir Compressor System
- I reached out to AirLift to see what could be going wrong with your Air Lift WirelessAIR Compressor System part # AL74000. They informed me that the A-09 code is a low voltage code. With this issue you want to check all of the connections on the system and most importantly ensure that both the positive and the negative connections on the wiring harness are connected directly to the battery terminals and not connected to any other power source or ground source.
Once you have confirmed...
view full answer... - Troubleshooting Right Side Brake/Turn Lamps Not Working on Trailer
- I took a look at the online owner's manual for your 2015 Chevy Silverado 1500 and it does look like you have replaced the fuses related to the left and right stop/turn lamps for the trailer. Since you now know the fuses are good, I recommend turning your attention to the trailer wiring.
I recommend first using a circuit tester like # PTW2993 to test the right side stop/turn signal light pin on your Silverado's 7-Way connector (3 o'clock position). You can have a buddy sit in the cab and...
view full answer... - Recommended Plug-in Adapter For Draw-Tite Brake Controller On 2015 Chevrolet Silverado 1500
- if the red light stays on all the time, it is because the red wire from the brake controller was attached to the wrong side of the stop light switch or possibly the cruise control.
You will need a circuit tester like part # PTW2993 and test the brake light switch on your vehicle under the dash at the top of the brake pedal and attach the red wire to the wire that only shows current when the brake pedal is pressed.
The best way to connect the Draw-Tite Activator, part # 5500 to your 2015...
view full answer... - Troubleshooting New Cargo Trailer Blowing Fuses In Tow Vehicle When Left Turn Signal Is Used
- I would be happy to help!
Since the fuse blows no matter which tow vehicle you use then the issue is that the left turn signal wire has a short in it somewhere. Since you mentioned you just purchased the cargo trailer brand new I would take it back to the dealer you purchased it from and have them repair the wire.
If not you will need get under the trailer and trace the left turn signal wire from the trailer connector back to the tail light looking for damage.
The damaged section will...
view full answer... - Brake Buddy Select 3 Doesn't Complete Test Cycle
- Thank you for your purchase from etrailer of the Brake Buddy Select 3 Portable Supplemental Braking System # HM39524. According to the manufacturer, whom I reached out to, the issue described could be in the Power Cord. Please examine the male terminals on both ends of the Power Cord to ensure the individual sections of each male pin are not compacted.
They should be spread slightly. If they are compacted, they may not be making solid contact, creating the intermittent power loss you...
view full answer... - Tekonsha Prodigy P3 No Power When Plugged Back In After First Use
- Since it worked well for you once, it sounds like you have a blown fuse. I recommend checking fuse 1 in the engine compartment fuse block. This fuse is for the trailer brake controller power. You will want to use a circuit tester, like # PTW2993, to see if the fuse has power.
If a blown fuse isn't the problem, you can use a circuit tester to make sure that power is reaching your brake controller by testing the black wire on the brake controller pigtail. If you have power to the brake controller,...
view full answer... - Isolating Brake Buddy Battery Charger
- I've found a solution for you! When disconnecting the negative side of the battery you loose power to everything in the vehicle which could include the braking system because all of his vehicle grounds are no longer grounded. With the charge line connected the way you have it, when you hook up to the motor home, because the charger is connected to both the positive and negative side of the battery, the charger now becomes the power and ground connection for the battery. This is why everything...
view full answer... - Can Hopkins Magnetic Light Kit part # C6304 Plug into Vehicle 7-Way
- Yes you can plug the Hopkins Magnetic Light Kit part # C6304 into the 7-way of your RV but you'll need to use a 7-way to 4-way adapter like part # HM47365 as well.
view full answer... - Troubleshooting RAS Raised 2021 Chevy Silverado 1500 3-1/4 Inches
- The only way the RAS system would raise your 2021 Chevy Silverado 1500 that much is if the leaf springs were extremely worn out. It is when your suspension is in good shape that you would expect a 1/2" rise since the leaf springs are only sagging a little bit and it is taking the vehicle back to factory ride height.
If your leaf springs weren't flat then you either have the wrong kit or something was installed incorrectly. The # RAS3611-HD you were looking at is not the correct kit for...
view full answer... - Troubleshooting 5th Wheel Wiring Harness and Trailer Brake System Error on 2017 Chevy Silverado 1500
- It sounds like a connection issue. I recommend removing the connections, checking for even the slightest bend in pins, and adding dielectric grease # 11755 to keep moisture and debris out. I recommend doing this at all 3 connection points of your # DM8555001 harness and then also adding that grease to the 7-way under the cover on both units.
This is the first I've heard of this issue with a 2017 model and also the first I've heard of the issue tied to installing a 5th wheel or gooseneck...
view full answer... - Troubleshooting Two Red Lights On All the Time on Brake Controller
- The issue could be a wiring issue or a faulty brake controller. The red light should only come on when you step on the brake pedal or when you push the manual override lever, with or without a trailer connected.
The first step I would take is to make sure the brake controller is installed properly. Your 2014 Chevrolet Silverado should have a port under the dash for a plug-in style wiring harness like part # 3016. If you are not using a plug-in wiring adapter, I recommend using this harness...
view full answer... - Tightening Nutset In Tailgate Of 2016 Chevrolet Silverado
- I called my contact at DeeZee and asked about the installation of the Tailgate Assist, part # DZ43102.
They told me that you can remove the screw and then put some Loctite like part # LT37420 on the threads of the screw and snug the screw back down. Let it sit a couple hours and it should secure the nutset for you.
view full answer... - Bestop Powerboard NX Wireless Running Boards Will Not Work with Front Passenger Door
- Since the Bestop Powerboards, # B7564115, still work properly with the rear door it sounds like the problem is with the connection (sensor) associated with the front door. Also check the wire connections. Look for any loose connections, frayed or pinched wires, or any corrosion that could be causing a lost connection.
If the sensor was knocked out of position or is missing then that would be the problem.
view full answer... - Troubleshooting 4-Way Trailer Connector without Drivers Side Brake/Turn Function at Connector
- You have done a great job isolating the problem. The trailer wasn't the issue, so I recommend returning that to its original state as a jump wire from the right to left side will only allow the right side functions. I've attached an article to assist.
Since you have determined no voltage at the truck connector, I recommend you disconnect the US Car Connector and check for the signal there as it may be a simple connection issue. If it is not an issue there, you will need to trace that...
view full answer... - Why is it Not Recommended to Use MaxxFan Roof Vent Above Shower
- While we have heard of people using electrical vents like the MaxxFan Roof Vent w/ 12V Fan # MA00-07000K above a tub/shower, it is not meant to be installed in that location because water from the shower and steam can potentially affect the electronics.
view full answer... - Replacement BrakeRite Actuator for Kit with Internal Board Issue
- Sounds like an internal issue with the circuit board which you'd have to speak directly to them about:
csdexter25@dexteraxle.com
view full answer...
Go To Results