I do have an option for you but there would be no way to attach a sway control mount to the Gen-Y Glyder Shock Absorbing Ball Mount part # 325-GH-12001. Instead, I recommend the Convert-A-Ball Dual-Cushioned, Adjustable Ball Mount part # CAB-UM which should then be able to used with the Reese Sway-Control Bracket part # RP26003. view full answer...
The only bike racks that are a confirmed fit for your 2014 Audi Q7, are the Hollywood Racks Over-the-Top rack # HRF2 the # HRF2-3. The good news is these racks are also a confirmed fit for your BMW 3 Series convertible. These racks are very popular and are easy to install and remove.
To carry women's bikes or bikes with sharply angled top tubes or step-through frames, using a frame adapter like part # HRBA-PRO is recommended. The adapter spans the distance between the seat post and the... view full answer...
Here's how you'll determine if the Thule Motion XT XL part # TH629906 that you referenced will allow the rear hatch of your 2019 Audi Q7 to open without interference. Move the front crossbar of your rack all the way forward and then measure from the center of it back to the rear hatch seam. If that distance is greater than 55 inches this box will fit and allow the rear door to open without interference.
The smaller version of the box part # TH629806 requires 51-1/4 inches instead. view full answer...
You will need to consult the vehicle owners manual to determine if tire chains can be used and if they can if there are any restrictions. If the tires are not the factory size then you will also want to contact an Audi dealer to determine if chains can be used. If they can then the only chains we have for a 295/35-21 tire are the K-Summit chains you have referenced, # TH02230K66.
These chains require zero millimeters of clearance on the back side of the tires. I have included some tire... view full answer...
While there are no major modifications or drilling required you will need to trim a small portion of the rear bumper fascia on your 2022 Audi Q7, for the Curt Trailer Hitch Receiver # C13277 to fit. I have a included an image that shows where the fascia is trimmed. The receiver will mount between the frame and the bumper beam on your Audi.
The Vehicle Wiring Harness # C59236 will allow for you to add a 4-way flat trailer connector to your Audi. view full answer...
The Curt hitch # C13277 is a confirmed fit on your 2017 Audi Q7 but the wiring harness # C55515 is not confirmed at this time. This harness does not fit any Audi models; it fits only U.S. vehicles that have an industry-standard round U.S. Car type connector, which is usually found under the rear bumper or tucked away behind the spare tire.
The correct 4-pole wiring harness options for your 2017 Q7 are Curt part # C59236 and Tekonsha # 119250KIT. The Curt is a hard-wired installation and... view full answer...
We have load stops that fit the AeroBlades, but the part you mentioned will not as they fit the Yakima bars. Instead, you will need the following part number for load stops that fit the Thule AeroBlade crossbars:
- Replacement Load Stops for Thule Aeroblade Load Bars # 753-3761 view full answer...
The correct Curt Trailer Hitch Receiver for a 2007 Audi Q7 is indeed part # 13220 which is a custom fit so no drilling into the vehicle is required and it has a hidden design for a very nice, clean finished install look. If you are looking to use the hitch for a bike rack and don't already have one, the Thule Hitching Post Pro part # TH934XTR is what I recommend as it offers the best value. view full answer...
In regards to the Curt Trailer Hitch Receiver part # C13277 for a 2019 Audi Q7, the distance from the collar to the center of the hitch pin is 2.14" and the distance from the center of the hitch pin hole to the end of the receiver is 4.48" per Curt. Therefore, you will have no issue with the Thule Apex Swing XT Bike Rack for 4 Bikes part # TH9027XT.
Unfortunately, we don't have the distance from the center of the hitch pin hole to the outer edge of the bumper but based on customer install... view full answer...
I have some good news for you because your 2019 Audi Q7 is 100 percent compatible with the ZCI Circuit Protected Vehicle Wiring Harness with 4-Pole Flat Trailer Connector and Installation Kit # 119250KIT.
Not only is it compatible, but there will be no splicing needed whatsoever to install this kit on your '19 Q7. I have added a link below to a video install for you on a similar model year Q7 for you to check out so you can get an idea of how it will install. view full answer...
The Rhino-Rack Vortex Aero roof rack system that fits your 2014 Audi Q7 fits all versions of the car so long as it has the flush mounted rails that run front to back. Your panoramic sunroof is not a problem with this crossbar rack system.
So all you need to do is order parts # RRVA126B-2 and # RRSX027. view full answer...
For your teardrop camper build I recommend the Demco A-Frame Trailer Coupler w/ Jack Hole # DM14791-97 over the Bulldog # BD028386 you were looking at. The latch style of the Demco is much easier and in my own personal opinion a safer design.
The eZ-Latch does not need to be tugged or manually activated to allow the ball into the coupler socket, nor does it have to be secured in place. Just make sure that the coupler is properly lined up with the ball when you lower it, and the rest is... view full answer...
Thanks for the photos, and based on them we do have what you need, which are over-the-hub disc brakes. The only thing you will need to verify is that you have a 5 on 4-1/2" bolt pattern on your hub; it looks like you do but you'll want to be sure by measuring from the center of your hub's wheel stud hole to the farthest edge of the opposite stud.
If that measures 4-1/2 inches you have a 5 on 4-1/2" bolt pattern. I have also added a link below to a printable bolt hole template. Assuming... view full answer...
The bracket you are referencing # RP26003 is designed for the more traditional fixed mount style ball mounts like # 40346 for example. I've attached an article to help you with the rise or drop needed for your application.
If you want to use an adjustable ball mount there are more limited options for sway bar compatibility. The MaxxTow Adjustable-Height Ball Mount - 2" Hitch - 10" Drop, 8" Rise - 5,000 lbs # MT70067, the Curt Channel Style Adjustable Ballmount - 5-1/4" Rise, 6-3/4"... view full answer...
To answer your first question, radial tires are superior to bias tires because they run cooler and are less prone to blowouts. The only reason to run a bias tire is if you do a lot of agricultural or off-road work.
In regard to fit, the Kenda S-Trail ST145R12 Radial Trailer Tire with 12" Galvanized Spoke Wheel - 5 on 4-1/2 - Load Range D # AM31202 might fit your Harbor Freight trailer, but there are a couple things you need to know first, starting with your trailer's bolt pattern. This... view full answer...
Thank you for your recent purchase of two pairs of Titan Chain Snow Tire Chains # TC2828CAM.
These chains do fit your specified 275/45-20 tire size, which is in the middle of the range of sizes these chains will fit. All tire chains are designed to fit more than one tire size, so it is not unusual for variances in fit - the slightly loose hold even after the cams are tightened.
First make sure that when you apply the chains that they are centered on the tires from left-to-right.
This... view full answer...
The Curt Echo Wireless Trailer Brake Controller part # C51180 won't work with an adapter like the Adapter 7 Pole to 5 Pole Flat part # A75TB because the 5th pin on a 5-way is typically for reverse so that's what it would correspond to on the Curt Echo. Therefore, you'd need to replace the 5-way with a 7-way, the Hopkins 7-Pole Round Connector part # H20042. view full answer...
Yes. I checked with Yakima and the Pin Adapters, # Y8880201, will fit the 2012 Audi Q7. When used on the Audi the RailGrabs require the 48 inch crossbars. If the bars on the Odyssey are shorter then it will not work on the Audi. You would need the 48 inch bars, # Y00408. view full answer...
Yes, the Konig Premium Self-Tensioning Snow Tire Chains - Diamond Pattern - D Link - K-Summit XXL - Size K67, part # TH2004565767, does fit your 2021 Audi Q7. This snow tire chain is tensioned via attachments to the lug nuts of your vehicle's wheel. As a result, it fits on the tread of the tire and the front of the wheel and not the rear of the wheel. The problems that occur with snow tire chains and tight clearances are almost always related to the chain on the rear of the tire. One of... view full answer...
Actually there is an adapter from Curt # C51522 that you can use to plug the Tekonsha Prodigy P3 # 90195 directly into your 2011 Audi Q7 if it has the factory 7-Way. You will need to cut the one end off of the adapter and splice the pigtail that comes with the P3 to the adapter (per color) for this to work.
If you don't have the factory 7-Way then you will need to run to your local dealer to get parts #1J0-972-782 and #000-979-228 to basically make an adapter (see attached article).
I... view full answer...
Go To Results