To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.
Features:
Specs:
Installation
This custom-fit T-One connector plugs into your vehicle's wiring harness, which is located inside your trunk, behind the tail lights on both the driver's side and passenger's side. You will need to remove some interior trim or carpeting to access the harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery and insert the provided fuse.
Once installation is complete, the 4-way flat connector will be stowed in an out-of-the-way location within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A ModuLite power module is built into this T-One connector. Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of your trailer. This power module functions as a tail light converter to combine the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
With a ModuLite, your trailer's lights will be powered without overloading your vehicle's electrical system. Because the module draws power directly from your car's battery and bypasses the electrical routes that are used by a basic wiring harness, there is virtually no draw on your tail light circuits.
California residents: click here
Average Customer Rating: 5.0 out of 5 stars (12 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom wiring harness. T-One connector plugs directly into existing wiring. Powered ModuLite reduces strain on wiring system.Removing the vehicle interior was the timely part of the install. Once that was done, wiring was very easy. However, vehicle designers should have allowed for a power tap under the dashboard for accessories. I did dress the wiring before reinstalling the interior panels. For this vehicle, hitch installation was made easier by removing the muffler from the vehicle and using a uni-bit to enlarge the access holes used for the install of the backing plates and bolts.
Extremely easy to install. Could not ask for any better customer service!
Fit the existing plugs on my 2012 Subaru Impreza. The time consuming part was placing the wire to the battery. Tucked it in along the interior out of sight.
I checked out the connectors on the tail lights and they are the same as previous years. Compared the service manual wiring diagrams to the pictures on the website and they corresponded to the same pinouts. They were the same. So the TowReady #118581 turned out to be plug-n-play afterall for my 2015 WRX Limited. Once I installed the kit, I tested it with a trailer light tester and everything worked as it should. I ran out of time or I would've hooked it up to the trailer tail lights for a true test. I'm installing a set of LED tail lights on the trailer that only draw 444mA (0.444A) along with a Curt C56196 to make it work with separate amber signals and stop lights. Other than routing the wiring to the battery (which I did through the interior of the car and through the firewall (which was a pain) but it has a clean factory finish that I wanted over splicing into the factory wiring harness.
Worked great after installation. No p roblems
Amazing product, just plug and play.
I recommend this to anyone who wants to save some time.
Thanks etrailer.
The kit was very easy to install and the instructions were clear. This was my first time installing wiring of any kind in a car and it took me under 30 min.
Great hardware and wiring ... definitely helps to be able to putt a trailer with my Impreza!
Great customer service!
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Charles F.
6/27/2016
Been working fine, no problems.