Tow Package Wiring Harness with 4 Pole Trailer Connector
Retail:$44.78
Our Price: $22.40
You Save: 50%
Confirmed to Fit
2012 Ford Escape
with factory Tow Package
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
- All Info
- Reviews (239)
- Q & A (0)
- Photos
2012 Ford Escape - Tow Package Wiring Harness with 4 Pole Trailer Connector
- Custom Fit
- Trailer Hitch Wiring
- 4 Flat
- No Converter
- Tekonsha
Please Note: This wiring harness will not work on vehicles with backup sensors!
If your vehicle has the tow package and backup sensors, use Modulite wiring harness 118551. Another option is to turn off the backup sensor with the switch in the car, and hardwire a standard 4-pole connector to the tow package plug in the back of the vehicle.
Tow Ready Tow Package Replacement Vehicle Wiring Harness by Draw-Tite, Hidden Hitch and Reese
- Provides a 4-pole flat trailer connector for the vehicle
- Quick and Easy
- No Cutting, Splicing or Taping
- Just Plug in the Connector and You're Ready to Tow
- Solid One Piece Construction
- 16 Gauge Bonded Wire w/ 4-Flat Plug
- "Factory" Appearance
- Simple Do-It-Yourself Instructions on Every Package
Can be used with 5-pole, 6-pole or 7-pole adapters.
Installation: The connection point is located underneath the vehicle, behind the rear bumper on the driver's side. Connector will have a protective cap that will need to be removed. The 4-pole trailer connector will be stowed under the vehicle close to the trailer hitch. A mounting bracket is recommended.
Tech Tip: It is always a good idea to apply a small amount of grease to all electrical connections to help prevent corrosion.
- Warning:
- Overloading circuit can cause fires. Do not exceed lower of towing manufacturer rating or:
- Max. stop/turn light: (7.5 amps)
- Max. tail lights: (7.5 amps)
Note: If your vehicle does not have the factory tow prep package, you will need 3 relays (TR38665 - sold separately) to be able to install this wiring harness.
118251 Tow Package Wiring Harness with 4 Pole Trailer Connector
Item # 118251
Installation Details
California residents: click here
Customer Satisfaction Score:
92% were satisfied with this product
8% of customers were not satisfied
- Wrong item was ordered
- Did not arrive in time
- Too difficult to install
Customer Reviews
Tow Package Wiring Harness with 4 Pole Trailer Connector - 118251
Average Customer Rating: 4.8 out of 5 stars (239 Customer Reviews)
by: Matthew07/11/2020
2008 Ford Escape
Simple addition to my 2008 Ford Escape to extend the factory trailer wiring harness from behind the bumper down to my new Drawtite trailer hitch reciever. I was fortunate enough to have the wire harness already installed including the fuses and relays. Might have taken 5 minutes to install and came with 2 zip ties to secure the extra wire. No tools needed.
by: Walter10/01/2020
Excellent product. Delivered fast and painless. Fits perfectly. Please note the factory will usually leave the required fuses and relays uninstalled even if you have the Tow Package. My 2009 Escape needed 2 mini fuses (1 - 15A and 1 - 20A) and 3 relays to energize the harness. These were available from the auto parts store. Refer to the photos. Photos #1&2- The two pages from the owner's manual that describes the sizes and locations of the fuses and relays. Photo #3- A photo of the fuse box located under the hood (front -left) with the fuses and relays installed. Photo #4- The installed connector.
by: Bob11/30/2017
Overall the product was delivered in a timely manner and in good condition. The only that was wrong was the box was all damaged. There were holes throughout the box, the box was crushed in certain spots, and the box was taped all over with the product sticking out of the box. When I received the package I expected the box to be in good shape not torn and damage-just lucky the hitch part that was sticking out was not bent
I plan on giving it to my husband as a Christmas gift so he can put a hitch on his vehicle.
Colleen
by: Chris 03/25/2024
Fits perfect - and shipped quickly!
by: John G.05/26/2013
2011 Mercury Mariner
Standard shipping was fast and product was as described. Zip ties are a little wimpy and short but worked.
by: Joseph 02/08/2023
2012 Ford Escape
the trailer hitch lined right up, Very easy to put in. I bought this to pull my little trail when I need to pick up plants ,trees, shrubs ect. Always a great product from etrailer. This is my 3rd from them for each of my cars.
by: Bast04/05/2011
2009 Ford Escape
After going to every shop in town (including the dealer), e trailer came through with the part I needed and quick shipping, when no one else even knew what I was talking about. Their product video made it easy to install the part, too! I love this solution and the fact that I didn't have to splice into any break lights.
Note of caution: The pre-wiring in the 2009 Escape is not powered, so you have to buy 3 relays (Ford part # 5L3Z-14N089-AA or package for all 3: 8L8T-15A416-AB). Make sure the relays have connection in your fuse panel first, though (locations 31C, D, and E). My Ford did not come with the OEM tow package, but the relays and this part worked great!
by: Mike R06/12/2014
2008 Ford Escape
Great communication. Received shipping information and delivery schedule with tracking information within a few hours after placing the order. Both the hitch and wiring harness were delivered right on schedule and I installed them both on my own without a lift in a little less than the 40 minutes indicated. Definitely will use etrailer again.
Mike R.
6/12/2015
Fantastic! Exactly as I wanted.
by: Matt C06/09/2011
Overall a good experience, it should list some where that the tow package is required from the factory in order for this harness to work. As all escapes and tributes are wired from the factory, but they don't necessarily have the left turn, right turn and break light relays in the fuse box for towing (fuses 31c,d, and e). E-trailer has a good website, customer service and products though, and I would buy from them again.
Judi
6/11/2014
What fuse amps did you put in your fuse box to make the plug work?
Matt C.
6/16/2014
It was a while ago, but Im pretty sure they were 5 amp fuses.
by: Herb M.05/05/2013
2008 Ford Escape
The product was easy to install; exactly as shown in the video. Until I looked on your site I was not aware that the 2008 Ford Escape was tow-ready. I plugged in the wiring harness, installed the three relays under the hood and I was ready to go.
Herb M.
6/6/2014
I do not use the hitch all that often, but when I do, it is great. The original reason I purchased it was to help move my son from Cincinnati, Ohio to Atlanta, Georgia. We rented a trailer, hooked it up, loaded up his stuff, and finished the move. I have no regrets purchasing these items.
by: Danny09/09/2023
2012 Ford Escape
Good price exactly what I wanted and it arrived when they said it would.
by: Crash Survivor12/07/2016
2009 Ford Escape
Execellent wireing kit. Direct fit . Plug and play. Very ez to install ! (Hint: my truck did not come with trailer package from the factory, had to install relays in underhood fuse box)
Daniel B.
12/11/2017
STILL WORKING AS WHEN NEW, PRODUCT HAS HELD UP THROUGH ALL 4 SEASONS OF MICHIGAN WEATHER
by: John08/01/2018
2009 Ford Escape
Clicked right in and worked fine once the additional relays were added to the under-hood fuse box of our Escape. If you didn't order your car with a hitch the required relays may not be installed and power won't flow to this harness. You can get the relays from auto stores, your auto maker, or [on-line].
Heather A.
8/1/2018
The 3 relays you will need to activate the tow package on the 2009 Ford Escape are 12 volt 4 terminal relays which you can find at an Auto parts store.
by: SD. 06/24/2009
2008 Ford Escape
Caution!! Check your Fusebox!!Be very careful with this product, unless your fuse box has the recievers for the relays (which you have to buy extra from FORD!!), it will not work!!
Even tho my 2008 Ford Escape had the wiring harness in back, I had to buy fuses and relays ($23/ea and you need 3 of them), my fusebox was NOT equiped with the recepticles for the relays OR fuses. I have to now go back and buy a different harness.
I just wasted $15 and 2 weeks messing with this one.
Patrick B.
11/29/2012
This harness is intended only for Escapes that have the factory tow prep package. Though most Escapes have the port, if they do not have the prep package, the rest of the electrical system may not support the rear port.
by: Joe L.11/14/2014
Got my harness fast it was inexpensive and was easy to install just watch the video and Cathy T. ext 381 was knowledgeable and pleasent to talk to
Joe L.
11/14/2015
Everything still works perfectly
by: Brian S03/13/2017
2008 Mercury Mariner
This worked perfectly on my 2008 Mercury Mariner that did not come with a factory hitch, however was already equipped with all necessary relays for functioning trailer lights. All I had to do was connect this to the existing port behind the bumper, zip-tie the excess wire to the bumper support for a nice clean look, and I was good to go with perfectly functioning trailer lights. Thank you etrailer for this product, it delivers and is well worth the cost.
by: Bill Titus05/01/2017
2008 Ford Escape
Bill Titus
Order #105192362
Not a good experience.
Part (118251) quality looked good and it fit the factory plug.
Problem was it is useless in my case. (and many others on the internet)
My vehicle has factory trailer plug – but also needs 3 relays and 2 fuses. Problem is Ford does not wire the fuse box for them.
This is what all the people on the Internet experienced.
Lucky I did not buy the expensive relays as some did!
I guess I need to order 118551 kit.
I feel I should have had that info. at the start.
Saying the kit is for vehicle with factory tow package is not enough info. If you have tow package – why do you need your plug?
MRT
by: Ned J05/01/2017
2009 Ford Escape
Excellent and easy to install. Hardest part was getting the factory cap off the factory connector.
I wish I had poked around on the etrailer website a little more and had learned about the need for the three relays (31C, 31D, and 31E) and the two fuses (#8 and #14) before I ordered my hitch and this wiring kit. I would have ordered the relays along with everything else. They are about one-third the price from etrailer as they are at my local parts store.
by: Steve M05/06/2014
2009 Ford Escape
This item, and shipping costs, were well priced, very well packaged and everything worked perfectly.
Even more so, the product was had to find locally and was not only available with etrailer, but was so easy to find though the website.
This was for a 2009 Ford Escape and other reviews suggestions to look in the fuse box to see if it contained the three relays required to power the trailer harness was a good tip.
Mine did not have the relays but it did have the female connectors in the sockets meaning that fuse box was wired for them.
The relays (x3) can be purchased from etrailer # TR38665 and work perfectly.
by: Stanley06/16/2019
this product did not meet my needs, it was falsely advertised and did not match my vehicle as claimed. I was forced to purchase a second adapter to complete my installation.
Mike L.
6/17/2019
This particular harness will only work on your 2011 Ford Escape if its equipped with the factory tow package. If it doesnt have the tow package, youll need 118551 instead.
by: Tom s06/19/2015
2012 Ford Escape
George have received all of my orders. Every thing is of the very best quality. Items were shipped and delivered in a very timely matter, videos were extremely helpful for installation, i have to say what a snap for all the wiring and installation of the E trailer hitch. Should any one ask I can only give you your staff, and your equipment a excellent , and superb. A Five Star rating is hardly enough. Thank You. Tom Sanders
by: Chas. P08/08/2011
2008 Ford Escape
I was blown away at the prices ($300-$400) I received to install a hitch on my vehicle (2008 Ford Escape) from 2 local shops. when I learned from etrailer.com (through your instructional video) how I could install the hitch myself I knew I was back in business. The hitch price was far cheaper and the installation was as simple as your video showed. All I needed was a 2nd pair of hands to help hold the hitch during installation and I borrowed a neighbors torque wrench. Now with my hitch installed I can finally get my boat and trailer to the lake!!
by: Marcus10/10/2021
Good idea, but a lot of extra wires. I can’t say for all Escapes but when I was about to hook this up I found a factory splice point. I’m assuming for a factory towing package. With some simple wiring knowledge, I was able to tap into that, eliminate a bunch of extra wires and disassembly.
by: Hauling It11/14/2016
2009 Ford Escape
This harness is everything that is advertised! It was completely plug-n-play with no problems in installation.
it is still working perfectly today, a year later, even going thru a New York winter. I coated the pins with dielectric grease on installation and it is still working at keeping everything from the salt corrosion.
25
239
Show More Reviews
See what our Experts say about this Tekonsha Custom Fit Vehicle Wiring
- 2012 Ford Explorer XLT Brake Controller Installation InstructionsYes, it sounds like you have the Hopkins 7-Way Adapter part # 37185 and are looking for a way to install it in your 2012 Ford Explorer that you recently installed a 4-way into. I attached an instructions link that will detail exactly what you will need to do and use to install the # 37185 in your vehicle and make your Tekonsha Trailer Brake Controller # TK63VR fully functional. I also attached a video that shows a similar installation for you to check out.
view full answer... - Light Kit and License Plate Bracket Recommendation for a Curt Cargo CarrierIt would require a little drilling, but I would recommend you get a etrailer License Plate and LED Tail Light Mounting Kit for Hitch Mounted Cargo Carrier Item # e98943-44LED. This kit comes with a license plate bracket also. Once you drilled holes to install the # 6504 on the Curt Cargo Carrier # C18100 it would install pretty easily and work very well. The Tow Package Wiring Harness # 118251 would also be the correct harness for your 2008 Ford Escape. I linked installation instructions...
view full answer... - Trailer Wiring Harness Recommendations for a 2008 Ford EscapeSince you have the plug you most likely have the tow package and the correct wiring harness to use would be the # 118251 that you referenced. You can test this by using a circuit tester like part # PTW2993 to test the pins of the connector for voltage when the taillight circuits of your vehicle are applied. If there is voltage there then the # 118251 would work well for you, otherwise you would want the # 118551. To activate that harness you would have to contact a Ford dealership to see...
view full answer... - How To Determine If My 2010 Ford Escape Has Towing Package and Extra Relays and FusesYour 2010 Ford Escape will have the extra fuses and relays in the fuse box if it came equipped with a factory tow package. The presence of the connector behind the bumper does not necessarily mean that you have the tow package. The connector might be there, but without the relays in the fuse box, the plug will not be active. If the relays are indeed in place, you can use the # 118251 harness that you referenced. If they are missing, take a look at the sockets where they would insert. If...
view full answer... - Installing a Trailer Brake Controller on a 2011 Ford Escape with Factory Tow PackageI spoke with my contact at Tekonsha about a brake controller wiring adapter for a 2011 Ford Escape with the Trailer Tow Package. He did not have specific information regarding the 2011 models, but historically the Ford Escape has been a hardwire only model. This means that you would first need a 4-Way wiring harness. With the factory tow package, you would use the Draw-Tite Custom Fit Vehicle Wiring, # 118251. Without a tow package, you would use the Tow Ready Custom Fit Vehicle Wiring,...
view full answer... - Will the Curt Class III Trailer Hitch Receiver # 13650 fit on a 2011 Mercury MarinerThe Curt Class III 2 Inch Hitch, part # 13650, will fit your 2011 Mercury Mariner. This hitch has a gross towing weight capacity of 3,500 lbs and a tongue weight capacity of 350 lbs, but you will want to check your owners manual to find out what the maximum towing capacity will be for your Mariner. I am including a link to the installation instructions on the Curt hitch. If you will be towing with this hitch I am including a list of other items you will need. Draw-Tite Ball Mount, part...
view full answer... - How to Determine If a 2010 Ford Escape Has the Factory Tow Package The easiest way to determine if your 2010 Ford Escape has the factory tow package would be to contact the dealer with your VIN as they would be able to tell you exactly whether or not your vehicle has the factory tow package. Another option for you would be to look for a black square connector which if present will be located underneath the drivers side of the vehicle near the spare tire. I recommend using the Tekonsha Trailer Wiring Harness part # 118551 for vehicles without the factory...
view full answer... - How to Hardwire a Trailer Connector on a 2008 Mercury Mariner If you do not wish to retain the factory backup sensors on your 2008 Mercury Mariner then you can use the 4-Pole Hardwire Kit with Circuit Tester part # 18252 instead of the Tow Package Wiring Harness with 4 Pole Trailer Connector part # 118251. In order to do this you will need to cut off the connector that attaches to the backup sensors and splice the above harness into those connections using the included circuit tester. The backup sensors and tow package wiring are on the same connector....
view full answer... - Is The Tekonsha T-One Kit # 118251 A Fit For 2011 Ford Escape Without Tow PackageDo you know if your Escape has the tow package? If not, the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118551 is the correct part. It installs behind the tail light per the included video but there should not be a 10 pin connector as part of the install. I'm thinking that the connector you found isn't for the the trailer wiring but for a different vehicle feature. The Tow Package Wiring Harness with 4 Pole Trailer Connectors # 118251 will fit to the 4-Way connector...
view full answer... - Installing a 7-Way Connector and a Brake Controller on a 2011 Ford Escape XLTYes, the Universal Wiring Kit # ETBC7 and the Tekonsha Prodigy P3 # 90195 will also fit your 2011 Ford Escape. If you already have a 4-Way then you won't need anything else, however if you don't have a 4-Way then you will need part # 118251 if you have the factory tow package or part # 118551 if you don't have the factory tow package. Attached is a sample installation video of the ETBC7 kit being installed on a 2011 Escape for you to reference. The brake controller being installed is the...
view full answer... - Troubleshooting Mismatched Wiring Connectors on a 2011 Ford EscapeThank you for the photos! I'd be more than happy to help you get the wiring figured out for your 2011 Ford Escape! The Tekonsha Connector # 118251 you purchased is the correct one for your Escape if you have the tow package. The connector this plugs into is located behind the driver's side bumper and will match exactly what you received. I'm not sure what plug it is that you found, but it definitely isn't for the trailer wiring (unless Ford gave you a completely different connection than...
view full answer...
- Wiring Harness for a 2009 Mercury Mariner without Factory Installed Trailer HitchYou indicate your Mariner did not come with a hitch. According to Ford's website, that means it is not wired for towing either. Product number 118251 is for vehicles with a towing package, so it will not work for your vehicle. You will need product number 118551, a wiring harness with a 4 pole trailer connector for your Mariner. This wiring harness may be used with 5-pole, 6-pole, or 7-pole adapters. This is a custom fit wiring harness for your Mariner. I will attach a wiring FAQ and...
view full answer... - Recommended Trailer Wiring Harness for a 2012 Ford EscapeThe trailer wiring harness I recommend for a 2012 Ford Escape without tow package is the T-One Vehicle Wiring Harness with 4-Pole Flat part # 118551 which plugs in behind the tail lights so you won't have to do any splicing. It will also work on models with the tow package if you aren't sure. Unfortunately, you'd need to reach out to the dealer to ask if you have the tow package if you don't know. The plug may be present for the connector but that does not mean the circuits for the tow...
view full answer... - Installing an Electric Trailer Brake Controller on a 2011 Ford Escape with Factory Tow PackageI believe I have found the question to which you are referring. Basically, the Ford escape has been a hardwire only model in terms of installing a brake controller. This would mean that it does not come with a port or factory harness for a brake controller. Instead, you would first need to install a 4-Way trailer connector if the vehicle does not already have one. For an Escape with a tow package, you would use Draw-Tite Custom Fit Vehicle Wiring, # 118251. With a 4-Way installed, you...
view full answer... - Which Trailer Wiring Harness Will Fit a 2011 Ford Escape LimitedSince your Escape has the back-up sensors, you will need to use the # 118551 modulite, as the # 118251 you referenced is not compatible with models that have the back-up sensors.
view full answer... - Correct 4-Way Trailer Wiring For My 2012 Ford EscapeLets start by making sure you are looking at the right connector. The connector is located between the rear bumper and the rear of the drivers side frame member, as you can see in the photo I have provided. The connector has a protective cover, which is actually pinned to the vehicle as shown in the photo. The connector will only be active if your Escape is equipped with the factory tow prep package. If you are unsure if your Escape has the prep package, you can call your Ford dealer,...
view full answer...
- Parts Needed to Add a Trailer Brake Controller and 7-Way Connector on a 2009 Ford EscapeSince you already have a 4-Way trailer connector on your 2009 Ford Escape, you will just need to add 2 more parts to equip a 7-Way and a brake controller. First, you will need a 4 and 7-Way installation Kit, # ETBC7. This kit will provide all of the wiring and components you will need to install a 7-Way and it provides wiring for the brake controller. I have included some links that will explain the installation of an ETBC7 kit for you. For a brake controller, I recommend the Tekonsha...
view full answer... - Is Any Bumper/Fascia Trimming Required to Install Curt Trailer Hitch # 12060 on a 2011 Ford EscapeAccording to the installation instructions for the Curt Trailer, # 12060, which I have linked for reference, you will not need to perform any rear fascia or bumper trimming to install the trailer hitch. There are only a few tech notes for this hitch: Drilling required only to enlarge existing access holes Fits Hybrid models as well Hitch will fit on models with a vibration dampener on the exhaust This trailer hitch comes with the recommended ball mount which should be used in the rise...
view full answer... - Will 4 Terminal Relay, # TR38665 Fit a 2008 Ford EscapeThe 4 Terminal Relay, # TR38665, will fit the 2008 and Newer Ford Escape. We have had customers state that these relays are good replacements for the ones offered from the dealer. They are designed to complete the factory tow package on several vehicles, including your Escape. However, before purchasing the relays, open the fuse box and take a close look at the sockets or landings that the relays would insert into. If the landings have the metal contacts in them, inserting the relays will...
view full answer...
- Trailer Wiring Harness Troubleshooting for a 2009 Ford EscapeUsually in situations where the wiring harness/converter has gone bad it is just due to a short from the trailer or a bad converter. But when it happens this often and with more than one brand, something else is going on. First, we need to make sure you are getting the correct harnesses. Both the CURT harness, # C56329, and the Tow Ready, # 118430, are designed for the 2009 Ford Escape WITHOUT tow package. If your Escape has a tow package, you would need # 118251. If you have a tow package...
view full answer... - Will Draw Tite Tow Package Wiring Harness with 4 Pole Trailer Connector Fit 2007 Ford EscapeOn the 2007 Ford Escape, a converter must be used so you will not be able to use Draw Tite Tow Package Wiring Harness with 4 Pole Trailer Connector # 118251, which you reference. We do, however, offer a custom fit harness, part # 118426, that converts the 4 wire system on the vehicle to a 3 wire system for the trailer. This harness also includes a power line that attaches directly to the vehicle battery. This allows the converter to power the trailer lights with a direct battery feed,...
view full answer... - Best Way to Check if a 2011 Ford Escape Limited Came with a Factory Towing PackageThe way to check if your 2011 Ford Escape came equipped with the factory tow package is call your local dealership and provide them the VIN number. The relays # TR38665 should work fine in conjunction with the Draw-Tite wiring harness, part # 118251 and would complete the tow package wiring on your Escape. I always recommend using dielectric grease such as # 11755 as it combats corrosion from water damage. I have included a couple installation videos and an FAQ for you too.
view full answer... - Trailer Wiring Harness Recommendation for a 2009 Ford EscapeSince you do not have the OE trailer hitch, the connector you found behind the bumper is not active. In some cases, the wiring can be activated by adding 3 of the # TR38665 relays to the fuse box under the hood, but you need to carefully examine the sockets that the relays would insert into. If the sockets do NOT have metal connection points or contacts in them, then the tow wiring circuits are incomplete and adding the relays will not activate the tow package wiring, in which case you...
view full answer... - 2012 Ford Escape 4-Pole Trailer Wiring HarnessWe offer trailer wiring for the 2012 Ford Escape for both versions with the factory tow package and without. For a 4-pole connector for the vehicle you can use part # 118251 which does plug in under the driver-side frame. If your Ford Escape does not have the factory tow prep package, you will need 3 relays (part # TR38665 - sold separately) to be able to install this wiring harness. The other option is a kit that completely bypasses any factory trailer wiring. Tekonsha 4-pole kit # 118551...
view full answer...
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
Expert Research:
Mike L
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Jameson C
Expert Research:
John H
Expert Research:
Adam R
Video Edited:
Zack K
Video Edited:
Andrew K
Video Edited:
Dustin K
Video by:
Joshua S
Test Fit:
Nicholas E
Test Fit:
Randy B
Installed by:
Cole B
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Larrry M.
1/9/2013
OK, here is my experience. I have a 2009 Ford Escape that did not have a factory hitch, but had the factory wiring. I looked in the fuse box under the hood and there were not relays in locations 31C, D, and E. I went to two Ford dealers looking for the OE relays and thank goodness they did not have any. I looked further on e trailers website and saw a Relay-4 Terminal 12v TR38665 listed. I ordered three and just plugged them in. Yes, you do need to check to see if you have the corresponding fuses in place - see owners manual. Very happy got three relays for $21 instead of $90 from Ford and I am able to use the factory wiring with the $15 Draw-Tite kit.