To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove all trunk floor coverings, storage trays, and the scuff panel to access these connection points. Once you've plugged in the T-connector, run the hot lead to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your trunk.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
California residents: click here
Average Customer Rating: 4.9 out of 5 stars (27 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.After having 2 kits sent by the largest supplier AM.... that were packeged with the wrong kits but marked ford focus hatchback, i contacted Curt and they suggested another supplier. Your profesionalism and tracking is second to none. Finally got the right one. I will be using you in the future
The hitch wiring went in great. I put in a thicker spacer 3/8 inch between the frame and the hitch which gave a better clearance from the plastic bumper cover and the receiver it went very well. The electrical wiring went well with the directions given. I have a focus ST and a pull a trailer with a zero turn 60 inch Ferris mower and it works very well.
The hitch is fairly straight forward and easy to install. The instructions are OK - not great - just OK, BUT... The etrailer videos for the hitch and wiring harness were BRILLIANT. My only criticism is that I found them by accident - I didn't realize they were out there. That being said, it took me less than 30 seconds to find them. They were much better than the printed instructions. I had a tablet out set next to me and it literally walked me through the painless process. Thanks! So, all in all, this was a very affordable and easy process thanks to etrailer.
Great harness. Clipped into my existing vehicle harness with no issues, trailer lights work great
Not a product review, I'll need some time to make that determination. As far as service goes, it seems like these guys are doing it right considering the niche they are in.
The online search/selection and order process was easy and efficient. I received an order confirmation immediately, and a shipping confirmation on the same day. The package arrived when they said it would. I also received a personalized delivery confirmation email which is always appreciated.
As of this writing I have not yet installed the tow bar and wiring kit for my 2015 Ford Focus ST, but my experience up to this point has been excellent.
Great all in one wiring harness. Took longer to install than the hitch. Could just be thrown into the spare tire well, but for a clean tidy install it takes a bit more time and effort. Take off your interior panels and do it right, you'll be much happier.
I installed the trailer hitch wiring in about 3 hours. It was very easy to do after watching the great video provided with this product. No problems...everything worked like a charm.
Everything I ordered came in with no issues. Wiring kit, receiver hitch and 2 balls. Quick shipping and no problems. Thank you!
Great product that works well, it’s just a pain to install. See my review of the Ford Focus RS Curt hitch as well. Definitely remove your lights even though it doesn’t say to.
Good instructions, worked the first time
Rick K.
1/16/2018
Both the hitch and the wiring harness are fine. I had trouble connecting the wiring harness because I did not pay close enough attention to the pictures in the instructions.
The product was at my door in less than a week fit perfectly worked just as described very happy with their service thanks a lot etrailer
etrailer makes me fell like they care and then prove it by their actions. One awesome company.
Installed perfectly. Did not run the positive wire under the car, instead I ran under trim along driver side of the interior and through a plug on the firewall about pedals. I do not like the idea of that wire underneath a new car.
Great company. Arrived on time. Very easy detailed instructions. Will buy from them again
Great product worked as it should. Came on time as promised ! Communication was great tracking the shipment
Will do buisness again
Product arrived within 2 days wow, The package was exactly as described and had video clips showing how to install. Great company, excellent service.
Thanks
Good product, used etrailer several times, always good.
Works great on my Ford Focus ST. It's not trivial to run the wire up to the battery, if you don't have a lift, but it can be done with a little time.
got it and haven't instaled it yet
Easy to install. Excellent value. Highly recommend!!
great product and fast service
everything looks right
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Matt
5/17/2020
Still works perfectly