Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge
(935 reviews)
Price: $16.36
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge
Our Price: $16.36
Will this fit?
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
In-stock alternatives that can ship today
- All Info
- Reviews (935)
- Q & A (0)
- Photos
2001 Dodge Dakota - Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Tekonsha
- Vehicle Specific
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your 's dash.
Features:
- Adapter is wired for:
- 1995-2009 Dodge Ram 1500/2500/3500, Full Size, all models
- 1997-2011 Dodge Dakota Pickup w/Factory Tow Package
- 1998-2009 Dodge Durango w/Factory Tow Package
- 2007-2009 Chrysler Aspen w/Factory Tow Package
- Wiring adapter eases installation of your electric brake controller
- Custom connector end plugs into the built-in port beneath the dash of your vehicle
- Other end plugs into the back of your electric brake controller
- Compatible time-delayed brake controllers: Draw-Tite Activator I (5100), Draw-Tite Activator II (5500), Draw-Tite Activator III (5520) and Tekonsha PowerTrac (39523)
- Compatible proportional brake controllers: Tekonsha Prodigy (90185), Tekonsha P2 (90885), Tekonsha P3 (90195), Tekonsha Primus IQ (TK90160) and Tekonsha Voyager (39510)
- Limited 1-year warranty
Installation of Tekonsha Brake Controller Adapter
This adapter plugs into the 4-pin connector on your vehicle's built-in brake control wiring harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.
To install your electric brake controller you need to connect the wiring of the controller to your vehicle. Certain manufacturers offer pre-wired options, typically known as tow packages, wherein these wires are run for you from the dash to the trailer connector on the back of your vehicle. Often, a brake controller wiring harness is included with your tow package. This harness plugs into a port beneath your dash and connects to the four wires of the brake controller. If, however, you have a brake controller with a plug in place of the four loose wires, you can use the Tekonsha adapter.
This adapter requires no hardwiring. It is designed to plug directly into your electric brake controller for the simplest installation possible. Because there are no wires to connect, installation is not permanent. You can unplug and remove your brake controller at any time and securely stow it away.
302000 Tekonsha Brake Control Wiring Adapter with 2 Plugs
Replaces 3020-P
Item # 3020-P
Installation Details
California residents: click here
Customer Satisfaction Score:
99% were satisfied with this product
1% of customers were not satisfied
- Product did not meet expectations
- Wrong item was ordered
- etrailer mistake
Customer Reviews
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge - 3020-P
Average Customer Rating: 4.9 out of 5 stars (935 Customer Reviews)
Install your electric brake controller quickly and easily with this custom wiring adapter. Simply plug one end of the adapter into your brake controller and then plug the other end into the built-in harness beneath your vehicle's dash.by: William03/23/2024
The brake controller worked great once I figured it out to put it on boost 2 after I replace the whole wire to a 10 gauge instead of a 12 but I don't think it was necessary but anyway it's working great
by: Roger05/26/2022
The cable arrived and we'll be camping tomorrow knowing the trailer brakes will be working thanks to your quick shipping and nicely constructed cable for my brake controller. It took 5 minutes to install.
by: Cory J03/29/2020
I’ve had the Timbren suspension enhancement system for a year now on my ‘99 Dodge 1500 4x4. I purchased this product because I had to tow my bumper pull three horse trailer from South Carolina to N. Central Montana. With a camper top, the bed loaded and the trailer loaded the truck sagged really bad. With the Timbrens on the sag went away completely. Making for a much safer less stressful experience while towing.
by: Blaine B.02/20/2015
2001 Jeep Grand Cherokee
This etrailer part "Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge - #3020-P" is a PERFECT fit for my 2001 Jeep Grand Cherokee and Tekonsha P3 brake controller.
After a LOT of research I discovered that in the Jeep Grand Cherokee WJ series (1999-2004) the 2001 model with "factory installed tow package", was the only year that did not have the 'the tucked away blue wire running back to the 7-pin trailer connector at the rear of the car. Instead a prewired connector was installed. According to the Jeep WJ users site, the Mopar part #56020142AB (wire harness with the appropriate connector for 2001 Jeep GC) had been discontinued, but Tekonsha Corp. (brake controller manufacturer) had a suitable replacement part. The page link on WJ Jeeps to the correct part at Tekonsha was broken and a search of Tekonsha's website produced no wiring that would even remotely help.
After crawling under my dash and removing the electrical fuse cover I found a blue connector. I took a photo of the connector so that I hopefully could find a connector that would help me avoid a complete engine compartment to rear bumper wiring installation.
Here on etrailer I found the brake controller I wanted and started looking at what I needed to make it operational. I tried everything I could think of (including writing the etrailer tech) to find out if the "Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge - #3020-P would work for my 2001 Jeep. No one was certain.
Sooo... I decided that at a cost of $14.99 it was worth it to buy - try - and return if necessary. I also figured if 'worst-came-to-worse' I may want to cut off the Dodge connector and use this shielded wire set instead of Tekonsha's wire harness by snipping off the Dodge connector.
5 minutes out of the box my Tekonsha P3 was lit up and a test light confirmed I had power to the factory installed 7-pin trailer connector at the rear using this etrailer part. It snapped into both connections perfectly.
The 30" length sounded adequate, but looked short out of the box. It turns out I have many mounting options with this length. Although it may not be mounted for a day or 2, I've decided to mount it on the left side of the steering wheel column. That's well out of the way of my long legs and yet in easy reach for manually engaging the trailer brake with the hand lever on my brake controller while driving.
I would recommend "Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Dodge - #3020-P" for ANY brake controller installed in a 2001 Jeep GC with the factory installed Mopar/Dodge connector. Just cut off the Tekonsha connector and butt connect the harnesses: BLUE to trailer connector * WHITE to ground - * RED to BRAKE switch (or recommended brake pedal connection point) * BLACK to battery +
Attached photos: original Mopar brake controller harness for factory installed tow package 2001 Jeep Grand Cherokee; etrailer's photo of the dodge connector for Tekonsha controller for visual comparison; a photo of the connector found under my dash; a photo of etrailer part #3020-P connected to my underdash connector; a photo showing the reach of the cable for a possible dash mount; and a photo showing the possible reach for a hidden ash tray mount.
by: Cole 06/14/2023
2003 Ram 2500
If you are struggling with an older trailer brake set up buy the Tekonsha. Just do it. No more delayed braking, buckling or pulsating just a smooth even slow down of the truck and the trailer at the same time. Installed with the wiring adapter on my 2003 Dodge 2500 Diesel. Simple plug and play. Went around the block a couple of times and had this thing dialed in perfectly. Spend an extra $ or 2 and buy this thing. you will be happy you did.
by: Tucker C06/15/2016
This product was a very easy install and initial setup. Only complaint is lack of option when trailer is not hooked up. I would like to present set my boost settings and break output and save them before actually getting hooked to my trailer. Then custom tune it once hooked up. Other than that, everything seems to be top notch.
When it came to the install, I chose to stray away from the typical mounting location and go with a point closer on the center console. If not for that the installation of the P3 would have taken less than 5 minutes from start to finish. Truly plug and play.
by: Alfred11/09/2017
2001 Dodge Durango
Purchased the wiring harness for my 2001 Dodge Durango and installed the brake controller. It was very easy, as my vehicle had a tow package installed already. Only took 20 minutes to hook up. Recommend this harness for similar suv's. Tested out perfectly. The price was better than all local sources. Trailer pic attached.
Al Fox
by: Charles04/11/2020
Tekonsha Prodigy P2 Electric brake controller was easy to install on my 2007 Ram 2500 diesel. I purchased the factory connector from e-trailer and snapped right in place. At 1st couldn’t find connector on vehicle but after going on e-trailer FAQ I found it. Picture included. Customer service was outstanding
by: William 09/15/2023
Installation was super easy with the vehicle specific wiring harness, just plug it in and screw the mounting bracket where you want it. It was that easy! Took about 15 mins or so. The controller works great, I towed about 10k lbs and stopping was very manageable. I would recommend this to anyone!
by: Rich 09/05/2022
Extremely easy to install.... True plug and play.
No issues.
Couldn't be happier
Rich
9/7/2023
This harness could not make installation and operation of my brake controller any simpler!!! Easily worth twice the price for the simplicity it provides
by: Brian D.07/03/2014
Dodge Ram Pickup
The P3 adapter fit my Ram 2500 perfectly and connected to the brake control unit. I had a question about installing the cable through the dash and was helped by email. Great support!
Brian D.
7/3/2015
The adapter has worked great!
by: Anthony01/16/2021
Bought it for my 05 cummins with the harness for the year make and model, plug and play mounted well works awesome
by: Robert08/17/2018
Makes an install super easy. Wasn’t quite long enough for where I put the brake controller ( at the manual gear shift ). Would work for the usual place under the steering column, left or right sides . Etrailer kept me informed several times by email and phone of the back order on this cable. Great customer service. They still fulfilled the order quickly.
by: Perfect! 1999 Dodge 2500 Diesel03/14/2017
1999 Dodge Ram Pickup
This is a plug and play with the P3 controller. It was perfect for my application. It is plenty long enough to run your controller over to right of steering column. I actually put mine in the factory ash tray so that I could more easily see it/operate it, without obstructed view of steering wheel. It is a very tidy piece also. Looks great under dash. Service was excellent from sellers and fast shipping even to AK. To bad it isn't free shipping up here haha
by: Chris 03/28/2024
Works great
by: Robert 07/06/2023
2005 Dodge Ram Pickup
Plugged right in to my 2005 Dodge Ram 3500. Made brake controller install super easy. Long enough IMO with proper routing as long as you are mounting in the below steering wheel location.
by: Samuel02/07/2020
I ordered the Tekonsha P3 and a wire harness for my 2006 Dodge 1500. The harness matched perfect and took about 10 minutes to attach it and zip tie it down. The P3 bracket took about 15 minutes and I was ready to go. Thank you all at etrailer for having the right info and the right set up for my vehicle. I say that due to getting the wrong wire harness on items I've ordered elsewhere. If I need anything else for my trailers I will use you all again!
by: James07/25/2022
Worked great . Used force meter to test output . Clean in stall. Unit appears to always be powered. Hot in summer heat so will only connect to power when using
by: Nate05/09/2014
Dodge
Plugs right into the blue trailer wiring harness on my '08 Dodge. Makes install just plug and play. Get the harness, save yourself a lot of trouble.
by: Pat M04/29/2014
Dodge Ram Pickup
After receiving my Tekonsha Brake control and a super easy installation into my 04' Dodge Ram 1500, I am on the road with my new Toy Hauler!
by: Steve 02/09/2024
Worked perfectly
by: Jerry Fairchild 09/17/2016
Dodge
Seems to be a wonderful product installed it on my 99 Dodge truck in about 15 minutes plug it in hooked up the trailer went up the road and back worked great all together about 20 minutes done simple and easy back home enjoying a cold beer in back yard
by: Glyn07/31/2023
It fit perfectly, made the job go smoother and faster and best of all no stripping/splicing wires, just plug and play.
by: Brandon 02/06/2023
I bought this for my dad's truck. He had called several local businesses about buying a plug and play brake controller and was told by all that there wasn't one made for his truck amd they would have to install and wore one up. I ordered this and installed it in 5 minutes, not including mounting it. It has worked great for him since.
by: Buddy08/13/2023
Made install for new controller so simp le.
25
935
Show More Reviews
See what our Experts say about this Tekonsha Accessories and Parts
- Brake Controller Only Outputs 3.4 Volts With Controller Set to MaxIf you are testing the connector on your truck with the brake controller set to it highest setting and using the manual override then there is definitely a problem if you are only getting 3.4V. You will want to start off by inspecting the connector on your truck. Look for any white or green looking residue as that can be corrosion. If that looks good then you will want to sever the Blue wire about 6 inches away from your brake controller and test it. If you are getting 12V at that point...
view full answer... - Parts Needed to Install a Trailer Brake Controller on a 2004 Dodge Ram 3500 with No Tow PackageI will be able to help you out, no problem. There were a couple of wiring situations you could get on the 2004 Dodge Ram. You could get it with no trailer connector, another options was a 4-Way trailer connector, and finally, you could get a 7-Way trailer connector. Since you did not get a full tow package, I want to assume that you do not have the 7-Way. If you had a 4-Way, you would also have the port to plug in a wiring harness for the brake controller, # 3020-P. On the truck it is...
view full answer... - Parts Needed to Add a 7- and 4-Way Trailer Connector to a 2002 Dodge Ram 2500If your Ram has the square plug for the wiring harness, you could use the Multi-Plug T-One Connector Assembly, # 20135, to add a 4 and 7-Way connector. If you have a different wiring situation, to add a 7-Way and 4-Way trailer connector to your 2002 Dodge Ram, you will need to use # 37185. You will need to plug in the existing 4-Way that you have on the truck into the 37185. You will then need to ground the white wire to the truck frame. The purple wire is for reverse lights on the trailer...
view full answer... - Parts Needed To Install Redarc Tow Pro Liberty Trailer Brake Controller On a 2005 Dodge DakotaIf your 2005 Dodge Dakota came with the factory 7-way you will simply need the Tekonsha Plug-In Wiring Adapter # 3020-P, and Adapter # 331-TPH-017 to connect the Redarc Liberty # RED24FR. This will give you a plug and play connection without having to splice any wiring. If you do not have the factory wiring we have a 4-Way # 55323, 7-Way # ETBC7 and the Redarc # RED52VR. This will give you all the wiring you need for a hardwire install.
view full answer... - Where Does a Brake Controller Plug Into on a 2003 Dodge DakotaThe plug for a brake controller will only be present/functional if your 2003 Dodge Dakota came with a factory installed 7-Way trailer connector. The factory plug is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. Sometimes the connector will be tucked up with other wires, taped up so it isn't easily visible, or it could be behind the driver's side kick panel. For a Tekonsha brake controller such as # 90885 use wiring...
view full answer... - Brake Controller Recommendation for a 1999 Dodge Ram 3500 Dually and 5th Wheel TrailerFor your 1999 Dodge Ram 3500 Dually and 5th wheel trailer I recommend using a proportional brake controller. A proportional controller will apply the trailer brakes in proportion to how much the truck is braking. This is the safest way to stop and it reduces wear and tear on the trailer and truck brakes. The proportional controller I recommend is the P2 # 90885 because its easy to set up and use and it is reliable. If your truck came with a factory installed 7-Way connector then you will...
view full answer... - Operation Instructions for the Prodigy P2 Brake Controller and 3020-P Wiring Harness on a 2006 DodgeWe have the installation and operation instructions linked on our product page for the Tekonsha Prodigy P2 Proportional Brake Controller with Dodge Adapter, item # 90885 and wiring adapter # 3020-P. I have posted a link below for you to review and use to set up your brake controller in your Dodge truck. The P2 is a newer brake controller. You may have the original Prodigy brake controller in your truck if it was installed in the truck when it was purchased used. The original Prodigy has...
view full answer... - How to Install a Brake Controller on a 2002 Dodge Ram 1500There are plug-in brake controller adapters for your 2002 Dodge Ram 1500 but only for certain brake controllers and if you have a factory trailer connector. If the above is true then please let me know what brake controller you have and I will be glad to see if we have the correct plug-in brake controller adapter for you. For example, if you have the ever popular Tekonsha Prodigy P2 Trailer Brake Controller part # 90885 then you will need to use the Tekonsha Plug-In Wiring Adapter for Electric...
view full answer... - Parts Needed to Install a Trailer Brake Controller on a 1997 Dodge Ram 1500On your 1997 Dodge Ram 1500, if your truck did not come with a factory installed 4- or 7-Way trailer connector then that blue connector for a brake controller would not be there. If it did come with a factory 4- or 7-Way trailer connector then that connector should be there. You may have to fish around for it. It could have also fell behind the driver side kick panel. If you do not have a factory 4- or 7-Way then you will have to hardwire in the brake controller. You will start by adding...
view full answer... - Install Harness Needed to Install P2 or P3 Brake Controller in a 2007 Dodge RamThe P2 # 90885 and the P3 # 90195 are both excellent controllers. Internally they are the same controller. The only difference is the P3 has a more advanced display setup that allows for easier understanding of what's going on with the controller and trailer. The P2 would work well for you. To install either controller in a 2007 Dodge Ram would only require the install harness part # 3020-P.
view full answer... - Recommendations Of Parts Needed When Towing Trailer With Camper In Bed Of 2008 Dodge RamThe first thing you will want to do is make sure you have the clearance at the back of your truck with the camper on the bed for your trailer. You can use a yardstick or dowel and a tape measure. Place the dowel at the back edge of the camper and let it extend below the trailer hitch. Then measure from the center of the hitch pin hole to the dowel. That is the amount of clearance you need to clear the camper with your trailer. You can use that measurement to find the right ball mount....
view full answer...
- Plug In Brake Controller Adapter for the Tekonsha Prodigy P2 on a 2012 Ford F-150In order to install the Tekonsha Prodigy P2 Trailer Brake Controller part # 90885 on your 2012 Ford F-150 you are going to want to use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 22292 (3036-P). This is a direct fit option that will not require any cutting or splicing. The Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 3020-P is not correct for you as it is designed for Dodge trucks.
view full answer... - Brake Controller Recommendation for a 2004 Dodge Ram 2500 with Factory 7-WayFor a proportional brake controller I would recommend the Prodigy P2 Brake Controller part # 90885. This is our best selling brake controller because of how well it works and how easy it is to setup. To install this controller all you would need is the part # 3020-P since your truck is prewired for one like you stated.
view full answer... - What is the Correct Brake Controller Wiring Harness to Fit a 2001 Dodge Ram 1500The Brake Controller Wiring Harness # 3020-P is the only confirmed harness to fit your 2001 Dodge Ram 1500 truck. The plug that you need to connect to the trucks wiring is located up under the dash by the emergency brake. The plug is usually a blue in color. I have attached a photo of what this plug will look like under your dash. The picture of the plug that you sent use is of the OBD-II diagnostics port. This is the connection port where a automotive tech or the owner can connect a diagnostics...
view full answer...
- Brake Controller Install Harness Recommendation for 2001 Dodge Ram 1500The install harness you need for a Tekonsha brake controller designed to fit your 2001 Dodge Ram is the part # 3020-P which will plug into the port under your dash.
view full answer... - Do Colors of Brake Controller Install Harness # 3020-P Match 2008 Dodge Ram Wire ColorsThe correct brake controller install harness for your 2008 Dodge Ram 1500 is the part # 3020-P. It sounds like you have this connector since the pin out of it goes white wire, red wire, blue wire, and then black like you stated. The colors of this harness aren't supposed to match up with the colors of the wire on the Dodge connector. Manufacturers use different colors all the time. I attached an install video that shows how to use this harness to install a brake controller in a 2008 Ram...
view full answer... - What is Needed to Wire a Brake Controller on a 1996 Dodge Ram PickupIf your 1996 Dodge Ram has the factory 7-way connector at the rear of the vehicle, then all of the wires for the brake controller have been run. You will just need a brake controller wiring adapter. I recommend using part # 3020-S. This adapter plugs into the brake controller plug under the dash, to the left of the steering column taped to another harness near the emergency brake pedal. The four pigtail wires on the other end will be butt-connected to the brake controller, color to color. If...
view full answer... - How to Add a 7-Way Trailer Connector to a 2009 Dodge Ram 2500 with Factory 4-Way Trailer ConnectorIf the trailer has brakes then you are going to want to use the Installation Kit part # ETBC7 on your 2009 Dodge Ram 2500. If the trailer dose not have brake then yes you can just use the Adapter 4-Pole to 7-Pole and 4-Pole part # 37185. The adapter is actually the same one included in the above kit but you also receive the additional wires and circuit breakers needed to tow a trailer with brakes. If you also need a brake controller, I recommend using the Tekonsha Prodigy P2 Trailer Brake...
view full answer... - Wiring Adapter for Brake Controller Installation on 2005 Dodge Ram 2500If your Ram is equipped with the factory tow package with the 7-way trailer connector at the rear bumper, there will be a connection point under the dash for a brake controller. Behind the emergency brake pedal, there is a white box attached to the firewall. The connector for the brake controller is blue in color, and is typically located above or alongside the white box. I am not familiar with an Explorer brake controller. If you use the Draw-Tite Activator like the controller you referenced,...
view full answer... - Weight Distribution, Transmission Cooler and Brake Controller for 2006 Dodge DurangoAs a first step, I recommend you determine the towing capacity of your Durango. I have done some research on that vehicle, and saw several references that state that the Durango, regardless of the engine it has, can only tow 2000 lbs unless it is equipped with the trailer towing group. Check with your owners manual or or your Dodge dealer for more information. You then need to determine the as-towed, fully loaded tongue weight of your trailer. I will provide an article that shows how to...
view full answer...
- Installation of Tekonsha Electric Brake Controller in a 2003 Dodge DakotaWe don't have a video of a Tekonsha brake controller, like the P3 # 90195, being installed into a 2003 Dodge Dakota like yours but I've linked one of a 2009. This install also uses our # ETBC7 kit which you'll also need if your truck doesn't have a 7-way trailer connector already. If your truck has a factory 7-way then there is a wiring harness # 3020-P that plugs in under the dash. If you don't have the factory 7-way the controller will be hardwired in. The # ETBC7 kit includes everything...
view full answer... - Weight Distribution System and Brake Controller Recommendations for 2006 Dodge DurangoThe Reese # RP66074 Strait-Line Trunnion Weight Distribution System is designed for trailer tongue weights ranging from 600-1200 lbs, so weight rating-wise it'd be perfect. The Strait-Line system is our Go-To recommendation for long trailers that are susceptible to sway caused by crosswinds and turbulence caused by oncoming traffic. For a trunnion bar system, the shank provides up to 6-1/2 inches of rise and 1-1/4 inches of drop. The included shank works for many, but not all vehicles. To...
view full answer... - What Is Needed To Replace Factory Brake Controller On 2010 Dodge 3500 With Tekonsha Brake ControllerFor the 2010 Dodge 3500 Dually with a factory 7-way trailer connector you would need the Tekonsha Brake Control Adapter, # 3021-P, to hook up a Tekonsha brake controller to the factory brake controller port and bypass the factory brake controller. The Tekonsha Brake Control Adapter, # 3020-P, you have referenced will only fit up to 2009 Dodge 3500 vehicles. It will not work on your 2010 vehicle. On your 2010 Dodge 3500 there will be 2 different size gray plugs behind your factory brake...
view full answer... - I Need a Hookup For A 7 Pole From A 4 Pole Plug for 2007 Dodge Ram PickupActually the Universal Installation Kit for Trailer Brake Controller 7-Way # ETBC7 is what you need to plug into your existing 4 pole connection. This kit includes everything you need to install an electric trailer brake controller and the 7-way/4-flat adapter. The best brake controller to go with to plug into your 7-way connection is the Tekonsha Prodigy P3 Trailer Brake Controller # 90195. This proportional brake controller automatically levels when mounted within a 360-degree vertical...
view full answer...
Do you have a question about this Accessories and Part?
Info for this part was:
Installed by:
Joe V
Expert Research:
Jackie C
Expert Research:
Mike L
Expert Research:
Robert G
Expert Research:
Patrick B
Expert Research:
Michael H
Expert Research:
Jeff D
Expert Research:
Reno H
Expert Research:
Jameson C
Expert Research:
Adam R
Expert Research:
Jeffrey L
Video Edited:
Zack K
Video Edited:
Joshua S
Video Edited:
Kathleen M
Written by:
Lindsey S
Updated by:
Laura H
Updated by:
Wilson B
Updated by:
Alexander C
Updated by:
Isabelle B
Video by:
Alan C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Ramjet
5/27/2023
Have not had any problems with the cable or controller.