Modifications cannot be made to Curt Trailer Hitch Receiver # C12234 without potentially impacting its durability and safety (and less importantly its warranty), but there are suggestions in regards to the issue you are having with it hitting the muffler on your 2003 Pontiac Vibe.
This could be due to the exhaust pipe or the hanger hitting the hitch, and that looks like that may be the case for you. What I recommend is reading the help article I have linked for you entitled "How to Correct... view full answer...
In regards to the etrailer Trailer Hitch Receiver part # e98865 on your 2007 Pontiac Torrent, the first issue you are having with the weld nuts inside the bumper beam is most likely due to them being stripped. This would have most likely been caused by the threads not being cleaned properly before the bolt was threaded in. Unfortunately, the fix for this will be to either drill and tap these nuts with the next size up drill bit/tap or to remove the weld nut and then use a carriage bolt... view full answer...
The Curt Class II Trailer Hitch Receiver, part # C12225, that you referenced is a confirmed fit for your 2006 Pontiac Grand Prix. This trailer hitch has capacities of 3,500 lbs gross trailer weight and 350 lbs tongue weight.
You will need to add the weight of the ATV trailer with the weight of your 2014 Yamaha Grizzly and make sure you stay under the weight limit of trailer hitch. Additionally, you should consult the owner's manual of your Grand Prix to determine what Pontiac recommended... view full answer...
The short answer is both. There are attachment points on the bottom of the frame and on the bumper mounts. I have included a link to the installation instructions for you to view.
If you plan on doing some towing, the hitch comes with the correct ball mount, pin, and clip. For a 1-7/8 inch ball, you can use # 19256. For a 2 inch ball use # 19258. For trailer wiring use # 119178KIT. I have linked the wiring instructions as well. view full answer...
I spoke with my contact at Superchips and he said their Flashpaq F5 Performance Tuner, # SU5845, will allow you to disable the Displacement on Demand feature on your 2009 Pontiac G8 GT V8. This would get you by until you decide to change out the parts. view full answer...
The Tow Ready Multi-Plug T-One Connector Assembly, part # 20135 is a replacement for Chrysler, Jeep, Freightliner and Mitsubishi OEM trailer connectors.
For your Montana, I would recommend using Curt Connector, part # C55355 in conjunction with part # ETBC7 if you are wanting to install a brake controller. The Brake Controller Install Kit, part # ETBC7 includes everything necessary to install a brake controller, as well as the adapter to convert the 4-pole provided by part # C55355 to... view full answer...
The Curt Class II Receiver Hitch, part # 12234 includes all hardware necessary for installing the hitch. All hardware described or listed in the instructions will be included with the hitch. view full answer...
On a 2009 Pontiac Montana Van the problem is that the installation of a brake controller can shut down the brake light system in the van. The red brake wire that is on the back of the brake controller is normally connected to the cold side of the brake light switch to activate the trailer brakes when the brake pedal is applied. If that red wire from the brake controller is connected to the cold side of the brake light switch on the Montana Van it will shut down the whole brake light system.
I... view full answer...
The Curt Trailer Hitch Receiver - Custom Fit - Class I - 1-1/4" # C11109 is a confirmed custom fit for your 2002 Pontiac Sunfire that is not a GT. I attached an installation video for you.
If you plan on doing some towing, first consult the owner's manual to make sure it is permissible to do so and for the vehicle capacities. The proper ball mount for this hitch and vehicle is # 3592. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # 18252. view full answer...
The Curt hitch # 12221 is only a fit for the 2008 Pontiac Vibe GT models. Heat shield modification is only required for installation if the heat shield interferes with the hitch installation area.
If you do not have a GT model, then heat shield modification would not be required. I would recommend the Draw-Tite model # 24812, as this hitch does not require heat shield modification, and it includes a pin and clip, which would be required if you plan to tow a trailer. Ball mounts are sold... view full answer...
The installation of rear suspension enhancement kit # TGMRLUM is very straightforward on your 1995 Pontiac Grand Prix. You would start by lifting up the vehicle so that the axle is hanging freely, and you would locate the existing bump stop assembly. Remove the bump stop, but keep the fasteners, as these are used for the suspension kit installation.
Once you have cleared the area, you would install the rubber spring and bracket in the same location, using your OEM fasteners. Finish... view full answer...
Yes, the installation procedure you see in the video would be the same for both the 2008 and 2009 model years of the Pontiac Solstice. As long as your vehicle is not a GXP model, you would be able to use the hitch # 11119 you referenced.
To install the # 11119 CURT trailer hitch on your vehicle, you will first fish wire the included spacers and bolts through the existing holes on your vehicle frame. Then, you will place the passenger side attachment bracket over the exhaust with the driver's... view full answer...
The Demco SBS Stay-IN-Play DUO Supplemental Braking System part # SM99251 is a great option for a 2004 Pontiac Vibe. It is not something we have installed on this exact vehicle but there are many instances which I have run into personally where the brake booster is directly behind the firewall where the brake pedal is. The standard practice we use when this is an issue is to drill a small pilot hole through the firewall then run a small wire though this to see how much room is there before... view full answer...
Yes! The 4-way wiring harness is designed to send a signal to the brake lights and the turn signals. The green wire is for the right turn, the yellow will control the left turn and the brown wire will be the brake lights. For the wiring harness to function properly it will need to be grounded, that is what the white wire is for. This Curt T-Connector # C56012 wiring harness will directly plug into the plug located in your 2007 Pontiac Torrent and provide you with a 4-way plug for your... view full answer...
You would not need to remove or lower the vehicle exhaust to install hitch # 36288. This hitch is a fit for the 1999 through 2004 Oldsmobile Alero, and also the 1999 through 2005 Pontiac Grand Am, including GT models.
You can view the instructions for the # 36288 hitch, as well as a video showing a typical installation. view full answer...
Single axle fender # HP99VR is a weld on application, so it is intended to be mounted by welding it directly to the side of the trailer using a wire feed or stick style weld.
I would recommend using a certified welder in your area. view full answer...
The T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector part # 118458 does not replace any of the connectors on the vehicle rather T's into them. There are two connectors that you will be connecting to on the back of the taillight housing. One is a 3 prong and one is a 2 prong. You will need to be sure you are attaching the correct pigtail from the harness to the connector on the tail light. For example, 3 prong from vehicle to 3 prong from wiring harness etc.
We have a video... view full answer...
The Tow Ready Custom Fit Vehicle Wiring, # 118458, does not require a direct connection to the battery when installing and can be used on your 2003 Pontiac Vibe GT.
However, the benefit of a system that does include a direct connection to the battery, like Curt Custom Fit Vehicle Wiring, # 55057, is that it protects your vehicles sensitive wiring from too much amperage draw from the trailer lights, which could damage the electrical system on your 2003 Pontiac Vibe GT. The fuse protected... view full answer...
Draw-Tite Trailer Hitch Receiver # 36288 for your 2004 Pontiac Grand Am will require you to enlarge the two existing holes using a 1/2-inch drill bit. This is noted in step 2 of the linked instructions. I also linked a video showing this hitch installed on a 2002 Grand Am. view full answer...
The Draw-Tite hitch, part # 36426, will fit your 2008 G6 GXP as long as the body parts are factory parts and not dealer or aftermarket. According to the instructions, you will not have to cut or trim the rear fascia. I have added a link to the instructions below for you to review. view full answer...
Go To Results