Two Front M12 Bolts Will Not Tighten with etrailer Hitch e98865 On a 2007 Pontiac Torrent
Question:
I had two problems with this install. The two weld nuts under the license plate never torqued down. They were the only ones that I could tighten easily, but they never tightened up to the proper torque level. Second problem, the rear bolts that have to be threaded through the steel plate through the frame hole would not tighten because the steel plate spins freely in the frame. Any recommended solutions?
asked by: Brandon W
Helpful Expert Reply:
In regards to the etrailer Trailer Hitch Receiver part # e98865 on your 2007 Pontiac Torrent, the first issue you are having with the weld nuts inside the bumper beam is most likely due to them being stripped. This would have most likely been caused by the threads not being cleaned properly before the bolt was threaded in. Unfortunately, the fix for this will be to either drill and tap these nuts with the next size up drill bit/tap or to remove the weld nut and then use a carriage bolt and square washer.
The second issue you are having with the spacer spinning is most likely caused by using the smaller square spacer instead of the larger rectangular spacer as this would then catch on the frame rail preventing it from spinning while you are tying to tighten this.
Product Page this Question was Asked From
etrailer Trailer Hitch Receiver - Custom Fit - Matte Black Finish - Class III - 2"
- Trailer Hitch
- Custom Fit Hitch
- Class III
- 350 lbs TW
- 3500 lbs GTW
- 4000 lbs WD GTW
- 2 Inch Hitch
- 400 lbs WD TW
- Concealed Cross Tube
- etrailer
more information >
Featured Help Information
Instructions
Continue Researching
- Shop: Trailer Hitch
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Search Results: replacement hardware kit
- Q&A: Tap Size One Size Bigger than M12 - 1.25 for Hitch Install with Stripped Nut
- Video: etrailer Class III Trailer Hitch Installation - 2021 Subaru Crosstrek
- Video: etrailer.com Trailer Hitch Installation - 2014 GMC Terrain
- Search Results: rhk
- Search Results: replacement hardware kit for hitch
- Shop: Replacement Hardware Kit for Trailer Hitches
- Q&A: Replacement Hardware Kit for Curt 13241 Hitch on 2015 Nissan Frontier
- Q&A: Size Bolts Used for the Curt Hitch part # 13241
- Shop: 1/2" Bolt Leader
- Shop: Replacement Rectangular Washer for Thule Ride-On Adapter
- Search Results: rp3022
- Shop: Replacement Hardware Kit for Curt SecureLatch Pintle Mount
- Shop: Trailer Wiring
- Video: Choosing the Right Trailer Wiring
- Article: How to Choose the Right Trailer Hitch Class
- Shop: Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Search Results: 44649
- Q&A: Wiring a Camper Shell Third Brake Light on a 2017 Chevrolet Silverado
- Article: Trailer Wiring Diagrams
- Video: Choosing the Right Brake Controller
- Shop: Tekonsha Prodigy P3 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Search Results: 68149
- Q&A: 10k Dexter Replacement Hub for a 8-415
- Search Results: 25580
- Shop: Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
on Trailer Hitch
