Easy Grease Trailer Hub and Drum Assembly for 2K Axles - 7" - 5 on 4-1/2 - L44649 - Pre-Greased
(43 reviews)
Price: $86.24
In Stock
Easy Grease Trailer Hub and Drum Assembly for 2K Axles - 7" - 5 on 4-1/2 - L44649 - Pre-Greased
Item # AKHD-545-2-EZ-2K
Our Price: $86.24
In Stock
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Need help with installation?
Locate installers near me- All Info
- Reviews (43)
- Q & A (0)
- Photos
etrailer by AxleTek Trailer Hubs and Drums - AKHD-545-2-EZ-2K
- 5 on 4-1/2 Inch
- For 2000 lbs Axles
- 10 Inch Wheel
- 12 Inch Wheel
- Hub with Integrated Drum
- 1/2 Inch Stud
- Easy Grease
- EZ Lube
- Pre-Greased
- L44649
- L44649
- etrailer
Hub-and-drum assembly for your trailer. For electric or hydraulic brakes. Fits 2K Dexter E-Z Lube and etrailer Easy Grease axles. Inner bearing (L44649) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.
Features:
- Trailer hub-and-drum assembly provides surface area for brake shoes to grip when brake is activated
- Compatible with electric and hydraulic drum brakes
- Dexter E-Z Lube and etrailer Easy Grease-compatible grease cap makes lubricating bearings fast and easy
- Remove rubber plug to access zerk fitting on spindle - no need to disassemble hub
- Sturdy iron construction
- Zinc-enriched paint on drum adds durability
- Zinc-finished bolts resist corrosion
- Pre-greased hub-and-drum assembly is easy to install - no need to pack bearings
- Lithium complex, multipurpose grease keeps bearings lubricated
- Bearings, races, grease seal, grease cap, and lug nuts are included
- QAI and CSA certified
Specs:
- Application: 2,000-lb Dexter E-Z Lube and etrailer Easy Grease trailer axles with BTR spindles
- Compatible with standard axles from most manufacturers, including Dexter, Lippert (LCI), and AL-KO
- Actual drum dimensions: 7-5/8" diameter x 2-7/16" wide
- Works with 7" brake assembly
- Bolt pattern: 5 on 4-1/2"
- Wheel studs: 1/2" diameter x 1-1/4" long
- Grease cap flange diameter: 1.99"
- Weight capacity: 1,000 lbs
- Limited 1-year warranty
Bearing, Race, and Seal Information
- Bearings (included)
- Inner bearing: L44649 (1.063" inner diameter)
- Outer bearing: L44649 (1.063" inner diameter)
- Races (included)
- Inner race: L44610
- Outer race: L44610
- Grease seal (included): 10-9
- Inner diameter: 1.50"
- Outer diameter: 1.987"
Thoroughly Tested for Safety
This hub-and-drum assembly meets the requirements for certification by the Canadian Standards Association (CSA). The CSA creates standards, which when complied with ensure a safe and quality product. This assembly underwent extensive testing to measure stopping distances when braking. This assembly has also been tested by QAI for braking performance in a complete automotive setup and under real-world conditions to provide the most realistic scenario for the everyday driver.
E-Z Lube and Easy Grease-Compatible Assembly for Simple Lubrication
The grease cap on this hub-and-drum assembly is specially designed to work with your Dexter E-Z Lube or etrailer Easy Grease axle to make lubricating bearings quick and easy. Just remove the plug on the grease cap, attach a grease gun to the zerk fitting on the end of the spindle, and inject the grease. It will flow easily to both inner and outer bearings. Not only does this make lubricating the bearings easy, but it also helps to prevent corrosion of the hub. This is because you can lubricate the bearings without the mess of taking apart the entire assembly.
Determining the Bolt Pattern
The first number in the bolt pattern is the number of bolt holes. The second number denotes the diameter, in inches, of the circle on which the bolt holes sit.
On wheels with an even number of bolt holes, measure from the center of one bolt hole to the center of the hole directly across from it. (Example: 8 on 6-1/2 means 8 bolt holes with 6-1/2" from the center of one hole to the center of another on the opposite side.)
To determine the bolt-circle diameter on wheels with an odd number of bolt holes, measure from the center of any bolt hole to the point halfway between the two bolt holes directly across from the first. (Example: 5 on 4-1/2 means 5 bolt holes with 4-1/2" measured to a point halfway between the opposite bolt holes.)
Measuring the distance (D) from the center of one bolt hole on the wheel to the center of a bolt hole right next to it can also help to determine the bolt pattern.
- If D = 2-5/8", then the bolt pattern is 5 on 4-1/2"
- If D = 2-3/4", then the bolt pattern is 5 on 4-3/4"
- If D = 3", then the bolt pattern is 5 on 5"
- If D = 3-1/4", then the bolt pattern is 5 on 5-1/2"
KBD2-54522-19 AxleTek 7" Trailer Hub and Drum Assembly for 2,000-lb Axle with Hardware - 5 on 4-1/2 - EZ Lube - Pre Greased
Customer Satisfaction Score:
94% were satisfied with this product
6% of customers were not satisfied
- Wrong item was ordered
- etrailer mistake
- Product did not meet expectations
Customer Reviews
Easy Grease Trailer Hub and Drum Assembly for 2K Axles - 7" - 5 on 4-1/2 - L44649 - Pre-Greased - AKHD-545-2-EZ-2K
Average Customer Rating: 4.9 out of 5 stars (43 Customer Reviews)
Hub-and-drum assembly for your trailer. For electric or hydraulic brakes. Fits 2K Dexter E-Z Lube and etrailer Easy Grease axles. Inner bearing (L44649) and race, outer bearing (L44649) and race, grease seal, grease cap, and lug nuts included.by: William 12/29/2022
Exactly what I needed. Good quality. fits perfect on my Snowfire trailer!!!
by: Danny 08/03/2023
Couldn't have been easier!, Straight out of the box and onto the axle. Getting my axle buddies on there. Took a little bit of banging around but they seem to be spinning. True and definitely an improvement over the broken Coleman studs I had before.
by: Donn S11/12/2018
I just now completed changing out and adding the new hubs and brakes on my trailer. The only issue or difficulty was my error in ordering the correct hubs/brake drums. The return was properly handled and the new parts arrived in a timely manner. All I have left to check on is the functionality once install my brake controller in my truck. I would make additional purchases from etrailer.
by: Keith10/04/2018
I received within 4 days the wheel hub (with bearings and seal) together with backing plates that contained brake shoes and braking magnets. They installed perfectly on my Coleman popup trailer. Prices were reasonable. In fact the electric backing plate assemblies cost less than a previously purchased set of braking magnets.
Thanks for helping me get on the road again!
Keith
by: David01/25/2023
One question, does the magnet go on the top or bottom, I have seen them displayed both ways. I have already installed them with the magnets on the top. The right and left references looking forward, I presume..
by: Mark 01/19/2021
I installed these hubs and drums 1 years ago and in that time we have taken our camper on 12 trips locally (about 120 miles round trip each) and one big trip from Louisiana to Colorado and back which was close to 3,000 miles total. These hubs and bearing have performed perfectly. The drive to Colorado was 24 hours one way and the hubs never got hot. Everything was a perfect fit too.
by: Joe B10/03/2017
E trailer did a fantastic job.
Before order: Technical support / help was excellent.
Goal, conversion of a 1998 Floe snowmobile trailer from surge to electric brakes.
Problem, due to time and corrosion, I could only supply partial part numbers, spindle diameter.
etrailer did a fantastic job, researching, and getting me the correct part numbers, so I could order.
Julie did a great job.
She was very timely, communicated clearly and honestly, and just “kept me in the loop”.
I received the order came on the projected date, complete and undamaged. Excellent.
I would highly recommend etrailer, for your part needs.
by: David P07/17/2016
product worked just like it should . The video on youtube made installation a snap . Even with a snafu at the warehouse of the wrong bearings being shipped one phone call to the very helpful rep led to a quick resolution . I have dealt with etrailer before and am very satisfied with their products and service .
by: Bruce04/25/2018
Seems to be very good quality. These hubs/drums fit the Dexter axle of my pop up camper perfectly. I like that they came with races, bearings and seals. The races were already properly installed.
by: Brian04/05/2018
I now have 9780+ miles on this item.
I am going to replace the bearings. They still roll but one is getting a tick. About to go out. I guess I'd rather change them now as opposed to a 1000 miles from home.
by: David 01/04/2020
I have used etrailer several times and the experience is always the same... the correct parts at a fair price and delivered when they said it would be.
by: Justin12/31/2017
Fit and function are great. Price and quality are spot on. I will be ordering from etrailer next time I need parts.
by: Rollin08/15/2022
Everything looks good and price was great!
Installation still to come so will update after install.
by: Sam 05/12/2020
Worked well for our 1800lb pop up camper. Install was pretty simple.
by: Bart 11/19/2021
Work as advertised for my trailer build.
by: Randy12/07/2017
Great quality !!! Great prices !!! Fast shipping !!!
by: Chris10/26/2018
Great product as described. Fast service.
by: Aaron10/28/2018
Great product exactly as described. Great prices and most selection out there. Shipping was as fast as you can get. Don't hesitate to buy here! Thanks!
by: Bob08/16/2018
Everything arrived in good condition. The entire ordering process went very well.
by: Peter02/17/2022
Professionally pregreased well apprecia ted.
by: Sandra 09/16/2022
Great job.
by: Michael12/08/2017
Arrived on time and in great condition, very well packaged. I haven't installed yet.
by: Matthew01/15/2021
You had what i needed and it got here fast. Thanks
by: James07/19/2019
Same
by: Chuck11/08/2016
Great price and fast shipping!
25
43
Show More Reviews
See what our Experts say about this etrailer Trailer Hubs and Drums
- Can etrailer Hub # AKHD-545-2-EZ-2K Fit 8 inch Trailer WheelYes the etrailer hub/drum part # AKHD-545-2-EZ-2K that you referenced is compatible with 8 inch wheels like what you can see at the attached link to this page.
view full answer... - How to Determine Weight Rating of Dexter Trailer AxleThe Dexter axle code P29 refers to the plant where it was made, plant 29, but this does not include capacity information. If you can find the complete serial number for the axle we can contact Dexter to find out more about it, particularly its weight rating. The 7 x 1-3/4-inch hydraulic brakes we offer, all shown on the linked page, are typically intended for axles rated for 2500-lbs, such as left- and right-hand brake kit # 23-398-399 from Dexter. For a new hub/drum we have 7 x 1-3/4-inch...
view full answer... - Recommended Wheel That Fits the Trailer Hub and Drum Assembly # AKHD-545-2-EZ-2KThe Steel Solid Center Trailer Wheel # AM20053 that you referenced is not compatible with the Trailer Hub and Drum Assembly # AKHD-545-2-EZ-2K due to the difference in bolt pattern. The wheel has a 5 on 5-1/2 in bolt pattern and the hub has a 5 on 4-1/2 inch bolt pattern. For a wheel that is compatible with the Trailer Hub and Drum Assembly # AKHD-545-2-EZ-2K you would want the Steel Trailer Wheel # AM20046 which has the 10 inch x 6 inch rim and uses the 5 on 4-1/2 inch bolt pattern. I...
view full answer... - Parts to Add Electric Brakes to 2015 Marine Trailer with Tandem 2K AxlesYour combination of equipment is a bit confusing as the 10" wheels and 4,500 lb GVWR sounds like your axle capacity should be 2,000 lbs since you have a tandem axle setup. Even the idler hubs for 3,500 lb axle are normally used for 13" to 15" wheels. If you do in fact have 2K axles then here are the parts you need to add brakes to your axles: - Electric Trailer Brake Kit # AKEBRK-2 (1 per axle - these will fit with 10" wheels) - Hub and Drum Assembly # AKHD-545-2-EZ-2K (comes with...
view full answer... - Brake and Hub/Drum Recommendations for a 2K Axle on a Boat TrailerTo install the Brake Mounting Flange # 4-34 on your 2,000 lb axle you'll need to have an experienced welder/trailer shop do the installation for you as they would know the best placement for the flange. We don't do that kind of installation so I don't have any info regarding the placement of the flange. You can definitely get a new axle with a flange pre-installed but that's something you'll need to talk with a trailer shop about as the dimensions you took aren't standard. I also recommend...
view full answer... - What Parts Are Needed to Add Electric Brakes to a Trailer with a 2,000 Lb AxleIn order to install electric brakes on your trailer you will need a brake mounting flange, brake assembly, hub/drum, trailer wiring, breakaway kit, and brake controller. I have attached my recommendations on each of the following for you below: Brake Mounting Flange: part # 4-34 (2) Brake Assembly: part # AKEBRK-2 Hub/Drum: part # AKHD-545-2-EZ-2K (2) Trailer Wiring: part # HS381-9000 Breakaway System part # 20099 Brake Controller: part # 90885 In order to be sure the above hub/drum...
view full answer... - What is the Difference Between the 1k and 2k Hubs for EZ Lube AxlesThe difference between the # AKHD-545-2-EZ-1K and # AKHD-545-2-EZ-2K is what bearing is used, and they are not interchangeable. If your spindle uses an # L44643 bearing in the hubs then you'll need the 1k, and if your hub uses the # L44649 then you'll need the 2k.
view full answer... - What Do I Need to Install Electric Brakes on My Boat Trailer with Weight Capacity of 2232With a single axle trailer rated for 2232 lbs. you have either a 3500 lbs. or something closer to a 2000 lbs. axle. Before purchasing anything you need to determine the correct one which you can easily do by checking the bearings once you have the trailer. If your outer and inner bearings are both # L44643 that means you have a 2000 lbs. axle and need 7 inch brakes. Brake Assembly # AKEBRK-2L and # AKEBRK-2R and the Hub and Drum Assembly # AKHD-545-2-EZ-1K are what you need. If your...
view full answer... - Will Trailer Hub/Drum part # AKHD-545-2-EZ-2K Fit Tie Down 2.2k Trailer AxleYes, the hub part # AKHD-545-2-EZ-2K that you referenced will fit the axle you have on your trailer. The spindle dimensions you listed match what this hubs is designed to fit. It comes with bearings L44649 inner and outer which means they will fit directly to your spindle.
view full answer... - Recommended 2,000 Lb Trailer Axle with Brakes for Small TrailerThe best option we could provide you with is the Trailer Idler Axle Beam part # e48GR which measures 60" long and has a 2,000 lb weight capacity. It's not setup for brakes so in order to equip them you'd need to have a brake mounting flange welded on, the Brake Mounting Flange for 1-3/4" Round Trailer Axles part # 4-34. This will then allow you to add brakes like the Electric Trailer Brake Kit part # AKEBRK-2 and hubs/drums like the Easy Grease Trailer Hub and Drum Assembly for 2K Axles...
view full answer... - Determining The Correct Brake Assemblies For A 2007 Karavan SeaDoo Trailer The brake kit needed is going to depend on the axle capacity. Most likely you'll have a 2k axle so once you have new spindles welded on with a brake flange the etrailer Electric Trailer Brake Kit # AKEBRK-2 would be a great option to install. Keep in mind that there is a lefthand and righthand to these assemblies (small brake pad will face towards the trailer tongue). Once you have your brake assemblies in place you'll need to swap out the old idler hubs for a hub and drum kit. The fitment...
view full answer... - Parts Needed to Install Trailer Brakes on 2015 Livin Lite Quicksilver 10.0 Tent TrailerI can certainly help you determine what parts you need to add electric brakes to your 2015 Quicksilver 10.0 tent trailer. Based on my research, it looks like your trailer has a 2,000 pound axle. If that is the case you can use the following part numbers: Brake Mounting Flange - # 4-34 Brake Assemblies - # AKEBRK-2L left-hand side # AKEBRK-2R right-hand side Hub and Drums - # AKHD-545-2-EZ-2K for 5 on 4-1/2 inch wheel bolt pattern or # 8-173-16UC3 for 4 on 4 inch Breakaway Kit - # PS50-85-320 Before...
view full answer... - Replacement Parts for Camper Converted to Utility TrailerYour size 20.5x8-10 tire is the old way of expressing tire sizing. Tire sizing has since been converted to metric and the equivalent tire size to your existing tire is 205/65-10, which really isn't uncommon. The Kenda # AM3H460 would work for your trailer and has a load range E capacity of 1,650 lbs. at 90 psi. There really isn't an advantage going to a 5 lug hub. The maximum load range for your current tire size is E. The next larger sized tire that will give you the option of an E...
view full answer... - Is There a 3,500 Lb Trailer Axle with 72" Hub Face LengthI do have an option for you but all of our axles within the hub face range you to specified have a weight capacity under 3,500 lbs. The Trailer Axle with Idler Hubs part # e78GR for example has a hub face to hub face measurement of 72" and has a 2,000 lb weight capacity. It does not have brake flanges installed so if you wish to add brakes you'd need to weld these on yourself using the Brake Mounting Flange part # 4-34. You could then complete your setup using the Electric Trailer Brake...
view full answer... - Replacement Hubs for Boat Trailer with L44549 Inner and Outer BearingsI'm guessing you actually have bearings # L44649 and you either mistyped or the bearing number is difficult to read. Having # L44649 as both the inner and outer is a very popular combination on 2,000 pound axles. If you need to verify to be sure this is what you have measure the inner diameter of the bearings with a digital caliper, like part # PTW80157. It should meaure 1.063 inches. I've also done some research and found that bearing L44549 has the same dimensions as # L44649 so it...
view full answer... - Does the 2K Dexter Axle 5 on 4-1/2 Complete Hub-and-Drum Assembly Come Fully AssembledEverything comes with the Dexter Axle 5 on 4-1/2 Complete Hub-and-Drum Assembly # 8-257-5UC3-EZ but you will need to pack the bearings and then install them and the grease seal inside the hub and drum assembly. You can use a bearing packer like part # PTW1218 to make packing the grease into the bearings much easier. This tool requires the use of a grease gun like part # L30200 and a cartridge like part # L11465 if you don't already have these handy. If you'd rather avoid having to pack...
view full answer... - Will the 7" Trailer Hub and Drum Assembly Work with 8" WheelsThe smallest available wheel size that can be used with 7" drums like the Trailer Hub and Drum Assembly part # AKHD-545-2-EZ-2K is 10". Therefore, you'll have to upgrade wheels for which I recommend using the Kenda 205/65-10 Bias Trailer Tire with 10" White Wheel part # AM3H350. The issue is that 7" when referring to the size of the drum is for the inner diameter. The outer diameter will be more. There may be some combos that work but for the most part the two are incompatible (7" drum...
view full answer... - Availability of 2,000 lb Trailer Hub/Drums and AssembliesWe have 2,000 lb trailer brake assemblies like the part # AKEBRK-2R and # AKEBRK-2L which are 7 inch in diameter. A hub like the part # AKHD-545-2-EZ-2K would fit with these assemblies and with the standard 2,000 lb spindle dimensions. But you would want to verify the bearing numbers of your current hub. They would need to both be L44649.
view full answer... - Hub Recommendation to Replace Hub with L44649 Bearings Thanks for the dimensions and bolt pattern you listed from your current hubs. With that info I can help you pick out the hub you would need. For an idler hub (no trailer brakes) we have the part # AKIHUB-545-2-G-2K which will fit your spindle or for a hub with at brake drum we have the part # AKHD-545-2-EZ-2K which is a fit as well. The bearings are not made in the USA but at this time there really isn't any US made bearing options for trailers.
view full answer... - Replacement Hub for Triton Trailer Model Elite 22-101Yes, the etrailer.com trailer hub/drum # AKHD-545-2-EZ-2K will fit your trailer that currently has Dexter hubs # 8-257-5UC3. Either of these can be used on either side of the trailer so you'd just need to order a quantity of two and you'd be set.
view full answer... - Trailer Hub/Drum that has 7 inch Drum and 5 Lug Bolt PatternWe have hubs that fit your spindle but they are 10 inch drums like you said wouldn't work. We don't have any that would fit that have a drum that's smaller. If by chance both of your bearings are L44649 you could use the part # AKHD-545-2-EZ-2K which has the bolt pattern you need and the drum is 7 inch.
view full answer... - Replacement Hub and Drum for Pontoon Trailer with 205/65-10 Tires and BrakesSince you have a 10" wheel and brakes for your pontoon trailer it sounds like you're needing the Easy Grease Trailer Hub and Drum Assembly for 2K Axles # AKHD-545-2-EZ-2K. This is a 7" hub and drum assembly with a 5 on 4-1/2" bolt pattern and the L44649 inner/outer bearings with a grease seal 1.50" ID. You'll want to verify this matches with what you have on your end but I'm pretty sure this is what you're needing. Attached is a review video for you to check out.
view full answer... - 72 Inch Long Dexter Trailer Axle with 2,200 lb Capacity and Hub/Drums and AssembliesWe have a few different Dexter straight trailer axles. If you check out the link I attached you will see all of the 72 inch Dexter axles we offer. Since you need a setup with hub/drums and brake assemblies you would need to get the part # T20BTR-EZ-7258 which is a 2,200 lb axle without hubs and then go with hubs and assemblies to match it. For hubs you would need the part # AKHD-545-2-EZ-2K then for a left hand brake assembly part # AKEBRK-2L and for the right side part # AKEBRK-2R. These...
view full answer... - Parts Needed To Add Electric Trailer Brakes To Trailer With 2000lb Axle And 14 WheelsI have another option for you, but the Trailer Idler Hub for 2K E-Z Lube Axles # AKIHUB-545-2-LFEZ-2K you were looking at are not designed to be used with brakes. Since your spindle uses inner and outer bearing # L44649 the only hub and drum assembly that will fit is the Trailer Hub and Drum Assembly - 2K E-Z Lube Axles - 7" - 5 on 4-1/2 - L44649 - Pre-Greased # AKHD-545-2-EZ-2K which is only compatible with wheels up to 12" in diameter, and would use Electric Trailer Brake Kit - 7" #...
view full answer...
Do you have a question about this Trailer Hubs and Drum?
Info for this part was:
Edited by:
Lindsey S
Installed by:
Jeff D
Expert Research:
Jameson C
Expert Research:
Adam R
Updated by:
Wilson B
Updated by:
Mike S
Written by:
Alexander C
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Product Experts Available Now!
Call 1-800-940-8924
William
12/30/2023
Great!!!