Electric-hydraulic brake actuator with brake lines lets you use an electric brake controller from inside your vehicle to adjust and control your trailer's hydraulic brakes. Enjoy convenience as you achieve greater braking control and performance.
Features:
Specs:
Note: Do not power wash the Hydrastar actuator or take it through a commercial car wash. High-pressure water may damage the seals on the actuator.
The Hydrastar electric-over-hydraulic trailer brake actuator applies pressure to your trailer's hydraulic brake system in response to the electrical signals sent from your in-cab brake controller. As a result, your trailer's hydraulic brakes will be activated every time you apply the brakes in your vehicle or press the manual override on your controller. You will get responsive hydraulic braking, which you control conveniently from inside your vehicle with your electric brake controller.
Hydrastar Electric-Over-Hydraulic Actuator vs Standard Surge Brake Actuators
With the Hydrastar electric-over-hydraulic actuator, you can get all the benefits of towing with an electric brake controller while using hydraulic brakes. Because this actuator will activate according to the settings you have chosen for your brake controller (sold separately), you will have more control over when and how your trailer brakes engage. Depending on the features of your brake controller, you may be able to control both the rate and intensity with which your trailer's brakes activate. You can also use the manual override on your brake controller, which allows you to engage the trailer brakes without having to apply the brakes in your vehicle. And perhaps most impressive, if you have a proportional brake controller, your brakes will be activated with an intensity that matches the braking speed and power of your rig.
This pump-and-motor-based system increases response time compared with traditional actuators because the trailer brakes are triggered when you apply the brakes in the tow vehicle, as opposed to when the trailer pushes against the hitch ball. This not only gives you faster, more efficient braking, but it also eliminates the pushing sensation that occurs in setups that use standard surge brake actuators.
Hydrastar actuators are also beneficial because, unlike standard surge couplers, they allow you to activate your brakes when reversing down an incline, such as a boat ramp. Having the ability to brake in reverse gives you more control and prevents wear on your tow vehicle.
Hydrastar Installation
This Hydrastar electric-over-hydraulic brake actuator will give you years of trailer-stopping performance. The actuator mounts on your trailer's frame with the included hardware. Then it splices into the trailer's wiring and connects to your hydraulic brake lines from the 3/16" female port.
Durable Construction
Just like other Hydrastar electric-over-hydraulic actuator models, this system is built of extruded anodized aluminum for superior corrosion resistance. The weathertight seals protect internal components from the elements.
Brake Controller Compatibility
Not all electric trailer brake controllers work with this electric-over-hydraulic brake actuator. See the following table to determine compatibility with common models of brake controllers. For best performance, it is recommended that you use an aftermarket electric brake controller rather than an OEM factory-installed controller.
| Manufacturer | Vehicle Years/Controller Models | Compatible | Compatible if Used with HBA-CAM | |
|---|---|---|---|---|
| Vehicles | Ford | 2005-2006 | Yes | |
| 2007-2008 | No | Yes | ||
| 2009-2015 | Yes | |||
| Dodge | 2010-2015 | Yes | ||
| GMC/Chevy | 2007-2015 | No | Yes | |
| Brake Controllers | Drawtite | 5500 Activator II | Yes | |
| 5510 Activator II | Yes | |||
| Hayes | 81741B Energize III | Yes | ||
| 81760 Engage | Yes | |||
| 81792K G2 | Yes | |||
| 81725 Syncronizer | Yes | |||
| 81770 Endeavor | Yes | |||
| Hopkins | Impulse Digital 47325 | Yes | ||
| Insight 47297 | Yes | |||
| Brake Force 47225 | No | |||
| Reliance 47284 | No | |||
| Agility 47295 | No | |||
| Maxbrake | Brake Controller | Yes | ||
| Redneck | Redline TA900 | Yes | ||
| RedlineTA900A | No | |||
| RedlineTA1000 | No | |||
| RedlineTA1100 | No | |||
| RedlineTA1200 | No | |||
| Tekonsha | 90185 Prodigy | Yes | ||
| 90885 P2 | Yes | |||
| 90195 P3 | Yes | |||
| 90160 Primus IQ | No | |||
| 9030 Voyager | Yes | |||
| Valley | VA32812 Blackbird | Yes | ||
| VA32811 Phantom | Yes |
Average Customer Rating: 5.0 out of 5 stars (4 Customer Reviews)
Electric-hydraulic brake actuator with brake lines lets you use an electric brake controller from inside your vehicle to adjust and control your trailer's hydraulic brakes. Enjoy convenience as you achieve greater braking control and performance.
It's been a good kit so far!! Had all the supplies I needed when installing it on my 30' float. Worked good on my Alko/kelsey hayes brake kit.
Quick delivery, great service
Do you have a question about this Brake Actuator?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.