Self-Tapping Screw - 1/4" -14 x 3/4" Long - Zinc

See what our Experts say about this Flint Hill Goods Accessories and Parts

• Upgrading Big Tex #35SA Trailer With Brakes
  It sounds like your Big Tex trailer did not come with brakes. Based on this, to convert your trailer with no brakes, to adding electric brakes, on your Big Tex 35SA trailer, the first thing you need is a left and right brake kit. You could use the Dexter 23-26-27 kit (includes left and right) which matches your Dexter axle 4” X 4” brake flange. However, for a little more I would recommend Dexter # 23-468-469 Nev-R-Ajust self adjusting brake kit. Most people do not want to have to periodically...
  view full answer...
  
• Adding LED Lights To A Hollywood Racks Sport Rider SE 4
  We have definitely seen customers do this and modify racks like the EasyFold # TH903202 before using the LED kit part # 98174LED and the brackets # BK70BB to mount. You will also need some self-tapping screws # FA1131822, or drill and use the hardware of your choice to mount the brackets. Doing modifications on the Sport Rider SE 4 # HR1400Z can cause a voiding of the warranty so that's worth checking out with Hollywood Racks before taking this on. Another option to consider that doesn't...
  view full answer...
• Do the Scissor Stabilizer Jacks Come with Install Hardware
  The Scissor Stabilizer Jacks part # TJSCHD-24-4 do not come with installation hardware. That said, we do offer the self-tapping screws you'll need for this using part # FA1131822. In regards to quantity, you'll need a total of 16.
  view full answer...
• How to Ground a License Plate Light
  If you have ensured you have power to the light using a test light similar to the LCD Digital Circuit Tester part # PTW2992 then it has to be an issue with the ground. I have always liked making a ground if the original connection doesn't work. You can move it around a little and get contact but eventually it will fail again. Instead use a self tapping screw like Self-Tapping Screw part # FA1131822 and securing the wires to it with 1/4" ring terminal part # DW05702-1. This is going to...
  view full answer...
• Screws to Use with the Wire Loom Clamp part # A0500
  You would want to use some self-tapping screws like the part # FA1131822. These would not require you drill a pilot hole. Just line the screw up where you want it through the Loom part # A0500 and let the drill bit end of the screw drill the needed hole and the threads will pull it through and secure it.
  view full answer...
• What Screws To Use When Installing E-track To the Side Of Aluminum Trailer Frame
  Zinc plated screws are going to be the best option for use with aluminum to resist galvanic corrosion. This corrosion you are referring to is from two dissimilar metals reacting so you want to use the most similar metals when installing your E-track to the side wall aluminum frame trailer. It is always safest to add a rubber or sealant to keep the metals as separate as possible even when they are compatible metals. Many times self tapping screws like # FA1131822 are the best solution.
  view full answer...
• Parts Needed to Convert ETBC7L to ETBC7 on 2019 Subaru Outback
  In order to turn your # ETBC7L into the # ETBC7 and use a standard brake controller you will need the following parts: -12-10 Gauge Butt Connector # 05732-2 (Quantity of 2) -Self-Tapping Screw # FA1131822 (Quantity of 4) -Small Ring Terminal # 44-5310A (Quantity of 2) -Large Ring Terminal # 44-5356A (Quantity of 2) -20 Amp Circuit Breaker # 9506P -30 Amp Circuit Breaker # 38630 -Brake Output Wire # 10-1-1 (25 Feet) For the installation, you can follow along with the video attached...
  view full answer...
• Wiring Colors for Trailer 4-Way Connector/Wiring
  4-way wiring is pretty simple and standard. The pin with the white wire running to it that is jacketed is the ground, the one next to it is going to be brown and for running light circuit, next to it is yellow and is left turn/stop circuit, and next to that is right turn/stop circuit and is green.
  view full answer...
• Option for Securing E-Track to Floor Of Car Hauler
  I'd use 1/4 inch diameter lag bolts whose length is a bit more than the thickness of the floor. How many bolts you need would depend on what you're using the E-track for. I'd probably want a bolt fastening the track about every 12 inches or so, maybe closer together for a heavier load. Use a self tapper like # FA1131822 to attach to the steel floor supports if present.
  view full answer...
• Hardware Needed to Install the Brophy BK4F on a 2019 Nissan Frontier
  To install the Brophy # BK4F you can simply use self tapping screws like the # FA1131822 to secure this bracket to your hitch. You won't be able to use bolts since this is connected directly to the tube of the hitch on your 2019 Nissan Frontier. You could also use the # 18140 to allow for a no drill/screw application.
  view full answer...
• Powered Awning Setup For 2020 Boost XLR And Other Toy Haulers / RVs
  We do have a few options that you could consider in terms of a powered awning for your 2020 Forest River Boost XLR. In regard to the Thule awning, I really wish I could tell you which one you saw. Unfortunately we do not carry any powered Thule awnings at all, but I am more than happy to give you some excellent recommendations on the powered awnings we do carry. We offer awnings powered by an 18v rechargeable battery: Solera # LC729486 for black, and # LC730492 for white. We also offer...
  view full answer...
• Recommended 4-Way Trailer Wiring Harness For Adding New LED Lights To Vintage Trailer
  To wire the 4 clearance lights # MCL0040ABB, license plate light # M298C, and tail lights # STL190RB to your 12' long 75" wide vintage trailer, I recommend starting the 4-Way Wishbone Trailer Wiring Harness with 42" Ground Wire # A40W42B which is 40' long meaning you will have enough extra wire to connect all of the lights you are planning on adding. The # A40W42B will install as follows: Brown wire to each of the yellow wire on each of the # MCL0040ABB, to the brown wire on the # M298C,...
  view full answer...
• Installing the Ground from the RV Tail Light RVSTB60 on a Wood Trailer
  If you do not already have a ground wire running to the tail light for installing the RV Tail Light # RVSTB60 that you referenced, then that is what you will need to do. You can take 16 Gauge Wire # 16-1-1 and connect it to the White wire on the tail light using Deka Heat Shrink Butt Connector # DW05744-5. You will then need to route the wire to a clean, bare-metal surface and the ground it using a Deka Ring Terminal # DW05744-5. This ring terminal has a 1/4" inner diameter so you will...
  view full answer...
• How To Properly Ground The Wires On Electric Drum Brakes
  Typically the ground wire would be connected to the frame of the trailer using ground screws like # FA1131822 and a ring terminal like part # DW05740-1. Using heat shrink is always recommended to help prevent corrosion. Connecting the ground to the axle technically would work, but the frame will be a much more secure location. You should be able to find a good clean spot on the frame and keep the grounds protected and out of the elements as much as possible.
  view full answer...
• Availability of Self-Tapping Screws
  We offer two sizes of self-tapping button- (or washer-) head screws. Part # FA1131822 has an unslotted hex head and is 1/4 -14 x 3/4-inch long threads. Part # 101131802 is # 8 x 1/2-inch long.
  view full answer...
• Simple Light Needed for Horse Trailer Tack Room
  The easiest thing to use/install is the NightMinder RV Task Light # NM-Motion-011. This is a battery powered light that uses 3 AAA batteries (not included). All you need to do is get rechargeable batteries to avoid purchasing batteries constantly. It would also be good to get at least 6 batteries so you can have some charging while the others are in use. Obviously if you want to use more than one of this light then you'll want to get the appropriate amount of batteries. If you'd like something...
  view full answer...
• Replacement Scissor Jacks for Cruiser RV Fun Finder FB189 Travel Trailer
  Yes, from the specs available to me it appears your 2007 Cruiser RV Fun Finder FB189 has a dry weight of little more than 2,700 lbs. with another 3,000 lbs. plus cargo weight available; that's a lot for a smaller trailer. The etrailer Scissor Jacks with Handle and 24" Lift, # e99012, are rated for 5,000 lbs. per jack so this will work as a replacement even if you max out the 3,000 lb. cargo weight. These stabilizing scissor jacks can be either bolted or welded to the frame of your trailer...
  view full answer...
• Replacement 7 Way Connector for 2020 Volkswagen Atlas
  Yes. The Pollak Replacement 7-Pole, RV-Style Trailer Connector Socket - Vehicle End # PK11893 is designed to work as an OEM replacement if you have a factory 7 way that has been damaged and requires replacement. You would need some self tapping screws like the # FA1131822 to attach this to your vehicle. The style of connector this socket is designed to fit is found on nearly all vehicles that have 7-ways. Thankfully all of the manufacturers decided to use the same plug design which makes...
  view full answer...
  
• LED Tail Light Kit for a Curt Trailer Hitch Mount Cargo Carrier
  Since there isn't a specific light kit that will fit the Curt carrier # C18153, what you will need to do is use a light kit like # 98174LED, and then add 2 brackets part # BK70BB as they work with 6-1/2 inch oval lights. You will also need some self-tapping screws # FA1131822, or drill and use the hardware of your choice to mount the brackets. Also, ensure that your 2015 Subaru Forester has a 4-Way trailer connector to plug the light kit # 98174LED into. If you need to add trailer wiring,...
  view full answer...
• What to Do w/ the Black and Red Wire When Wiring a 7-Way Connector
  The black wire is usually the 12v power wire that typically goes in the 11 o'clock position on the trailer side 7-way connector as you are looking directly at the front of it. It'll keep your battery charged, run an electric jack, or something along those lines. Not the end of the world if you don't have anything to run it to. Now the red wire is going to do something with your left side trailer lights if you are wiring your 7-way in a standard configuration so it's pretty important. I...
  view full answer...
  
• Is Additional Converter Needed on Tow Ready T-One Vehicle Wiring Harness For 2003 Nissan Pathfinder
  No separate or additional converter is needed for the Tow Ready T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118361 for your 2003 Nissan Pathfinder. All plugs and converters needed for the wiring harness to combine your vehicle's separate wiring system are included. You will simply need to plug the harness into your Pathfinder's wiring behind the left and right vehicle taillights, as seen in the video I've attached. In the video, our installer is able to ground the...
  view full answer...
• Tail Light Kit for a Curt Trailer Hitch Mount Cargo Carrier
  Since there is no specific light kit that will fit the Curt carrier # C18153 what you will need to do is use a light kit like # 98174LED, and then add 2 brackets, # BK70BB. You will also need some self-tapping screws # FA1131822, or drill and use the hardware of your choice to mount the brackets. Also, make sure that your MDX has a 4-Way trailer connector to plug the light kit into. If you need to add trailer wiring, use # 118424 or # C56038.
  view full answer...
• Recommended Power Awning for 2016 Winnebago Trend 23L
  For your 2016 Winnebago Trend 23L, the awning that comes with the unit is 15 feet. For a complete power awning I recommend the Solera 12V XL Power RV Awning - 15' Wide - Extra-Long 9'8" Projection - Black Fade # LCV000334950-362243 which is a top of the line option. I've attached a video of the installation to assist. If you want to piece a system together, I recommend the Solera 12V Power RV Awning Conversion Kit - Universal - 69" Arms - Black # LC434723, the Solera Awning Rail Extrusion...
  view full answer...
• Light Kit and Other Ways to Add Visibility to Hitch-Mounted Cargo Carrier C18153
  For the Curt hitch-mount cargo carrier # C18153 there is no specific light kit offered but we can help you with the individual parts you'd need to install one. What you will need to do is use a light kit like # 98174LED, and then add 2 brackets # BK70BB. You will also need some self-tapping screws # FA1131822, or drill and use the hardware of your choice to mount the brackets. I noted in your purchase history that you have a 2011 Chevrolet Traverse, which will need to have a 4-pole...
  view full answer...

Do you have a question about this Accessories and Part?