Light Kit and Other Ways to Add Visibility to Hitch-Mounted Cargo Carrier C18153

Question

Question:

I have a CURT 18153 Basket-Style Cargo Carrier and was looking to add a trailer light kit. Is there a specific kit that works better for cargo carriers? I was also thinking that I might not need a light kit all the time either so is there a removable option?

asked by: Jim

0

Expert Reply:

For the Curt hitch-mount cargo carrier # C18153 there is no specific light kit offered but we can help you with the individual parts you'd need to install one.

What you will need to do is use a light kit like # 98174LED, and then add 2 brackets # BK70BB. You will also need some self-tapping screws # FA1131822, or drill and use the hardware of your choice to mount the brackets.

I noted in your purchase history that you have a 2011 Chevrolet Traverse, which will need to have a 4-pole wiring harness in place to power the carrier lights. If you do not have one already you can use part # 118384 if you have the factory tow package, or if not then use part # 118450.

Another way to add visibility to your carrier, and something you can do along with the light kit for extra safety, is to add conspicuity tape like # RE18T.

expert reply by: Adam R

0

Answer 1

The proper hardwire wiring harness for the #STL178RFPB GloLight LED trailer tail light is the #A47PB. A great and similar style side marker/clearance and turn light is the #STL78AB, this will already have the proper wires to install on your…

view full answer...

Answer 2

Best option would be to connect the #A47PB to the wiring you have on your trailer currently so that you can easily plug in the GloLight LED Trailer Tail Light #STL178RFPB. For butt connectors you'd then want the part #DW05714. This is a…

view full answer...

Answer 3

Its usually easiest to disconnect the trailer from the vehicle and test the trailer functions directly by connecting 12V power from the vehicle (or another) battery right to the various circuits on the trailer plug. This way of testing isolates the…

view full answer...

Answer 4

Basically, in any state in the union, if the rear license plate or lights are obscured in any way, a police officer can pull you over, regardless of the specific verbiage of the laws. Beyond that it is just a good idea to add lights for safey. For…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 10

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only…

view full answer...