Make installing your trailer wiring harness as easy as possible with a custom fit wiring harness. Trailer wiring from Draw-Tite, Curt, Pollak, Tow Ready, Bosal, and Hopkins eliminates or reduces the need to cut and splice wires. It also helps to protect your vehicle's sensitive electronics from mis-wired trailers.
Choose the year of your vehicle to the left to find a custom fit trailer wiring harness.
Videos
for Custom Fit Vehicle Wiring
Help Articles
Expert Answers
The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…
A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…
I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we…
If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…
Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video…
From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x…
Brake systems are not dependent on the hub bolt pattern. So you can use the Electric Trailer Brake Kit #AKEBRK-7-SA for 12 inch hub/drums or #AKEBRK-35-SA for 10 inch hub/drums. Then use #10-1-1 wire sold by the foot for your brake magnet wiring.…
I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and…
Normal operating temperatures for drum brakes range from 150-400 degrees F. During certain stopping conditions the brake heat can exceed 600 degrees. The effectiveness and stopping power of the brakes is significantly reduced at these higher…
I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions…
If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…
The part you referenced 127194TB is a double-lip seal with an inner diameter of 1.274-inches and an outer diameter of 1.983-inches. The available seal nearest to those dimensions that we offer is part #RG06-010, which is a double-lip seal sold as a…
Wiring Adapter Fitguide
Trailer Wiring Manufacturers
Search For Custom Fit Pontiac Solstice AccessoriesSelect A Category Below
Towing
Pontiac Solstice Trailer Hitch
Pontiac Solstice Trailer Wiring
Pontiac Solstice Brake Controller
Pontiac Solstice Towing Mirrors
Cargo Control
Pontiac Solstice Roof Rack
Pontiac Solstice Trunk Bike Rack
Performance Accessories
Pontiac Solstice Air Filter
Pontiac Solstice Suspension Enhancement
Pontiac Solstice Transmission Cooler
Pontiac Solstice Vehicle Lights
Pontiac Solstice Tire Chains
Pontiac Solstice Fluid Filters
Pontiac Solstice Salt Spreader
Vehicle Trim
Pontiac Solstice Floor Mats
Pontiac Solstice Trim Kits
Pontiac Solstice Vehicle Covers
Pontiac Solstice Side Window Vents
Pontiac Solstice Mud Flaps
Pontiac Solstice Vehicle Seat Covers
Pontiac Solstice Replacement Mirrors
Pontiac Solstice Windshield Wiper Blades
Pontiac Solstice Windshield Covers
Pontiac Solstice Vehicle Air Mattress