Summer Starts Here - Save up to 70%
Best 2014 Ford F-250 and F-350 Super Duty Hitch Options- Video
Today we're going to be taking a look at the best hitch options available for the 2014 Ford F250 and F350 Super Duty. Now when looking up hitches for this particular vehicle, these are the top three class 5 hitches for your Ford. At the top we have the CURT, part number C15810. Here we have the B&W, part number BWHDRH25401. At the bottom we have our SuperHitch from Torklift, part number TLF1002-30. Now all of these hitches are really for heavy duty or commercial use, but there are some differences, and we'll go ahead and go over some of those now. Now one of our first differences is going to be the actual hitch opening sizes. more
1/10/2017 2:13:46 PM
Best 2013 Ford F-250 and F-350 Super Duty Hitch Options- Video
Today we're going to be taking a look at the best hitch options available for the 2013 Ford F250 and F350 Super Duty. Now when looking up hitches for this particular vehicle, these are the top three class 5 hitches for your Ford. At the top we have the CURT, part number C15810. Here we have the B&W, part number BWHDRH25401. At the bottom we have our SuperHitch from Torklift, part number TLF1002-30. Now all of these hitches are really for heavy duty or commercial use, but there are some differences, and we'll go ahead and go over some of those now. Now one of our first differences is going to be the actual hitch opening sizes. more
1/10/2017 2:13:35 PM
Best 2012 Ford F-250 and F-350 Super Duty Hitch Options- Video
Today we're going to be taking a look at the best hitch options available for the 2012 Ford F250 and F350 Super Duty. Now when looking up hitches for this particular vehicle, these are the top three class 5 hitches for your Ford. At the top we have the CURT, part number C15810. Here we have the B&W, part number BWHDRH25401. At the bottom we have our SuperHitch from Torklift, part number TLF1002-30. Now all of these hitches are really for heavy duty or commercial use, but there are some differences, and we'll go ahead and go over some of those now. Now one of our first differences is going to be the actual hitch opening sizes. more
1/10/2017 2:13:23 PM
Best 2011 Ford F-250 and F-350 Super Duty Hitch Options- Video
Today we're going to be taking a look at the best hitch options available for the 2011 Ford F250 and F350 Super Duty. Now when looking up hitches for this particular vehicle, these are the top three class 5 hitches for your Ford. At the top we have the CURT, part number C15810. Here we have the B&W, part number BWHDRH25401. At the bottom we have our SuperHitch from Torklift, part number TLF1002-30. Now all of these hitches are really for heavy duty or commercial use, but there are some differences, and we'll go ahead and go over some of those now. Now one of our first differences is going to be the actual hitch opening sizes. more
1/10/2017 2:13:11 PM
Best 1999 Ford F-250 Hitch Options- Video
Today on our 1999 Ford F-250 we're going to take a look at our best hitch options available, starting with the Curt Class 4 Hitch, part number C14355. This is a 2" x 2" receiver tube. It comes with a 1.000 lb tongue capacity and a 10,000 lb tow capacity. When using a weight distribution system, this hitch has a 1,200 lb tongue weight capacity and a 12,000 lb gross towing capacity. We've got our Curt Class 5, part number C15410. This is a 2" x 2" receiver tube, tongue weight capacity is going to be 2,550 lbs and a 17,000 lb tow capacity. more
9/16/2015 3:38:52 PM
Trailer Hitch Installation - 2007 Ford F-250 - B&W- Video
Today, on our 2007 Ford F250, we're going to review and install the B&W Class V 2" Receiver Tube Hitch, part number B-W-H-D-R-H-2-5-2-3-0. Here's what it's going to look like once it's installed. This is our Class V hitch. It's a completely steel and a no drill install. We've got a square crosstube that comes into a receiver tube. Here at our receiver tube on each side is our easy to use chain hold-downs and our 5/8th pin hole that goes all the way through the receiver tube for securing our attachments. more
8/21/2015 3:42:11 PM
Trailer Hitch Installation - 2007 Ford F-250 - Curt- Video
Today, on our 2007 Ford F-250 we're going to review and install, the Curt Class V, 2-1/2 inch Receiver Tube Hitch, part number C15810. Now here's what our hitch is going to look like once it's installed. Our hitch is a super strong, square tube constructed, fully welded, with a matte and black coated finish. This is our big heavy duty hitch, so we've also got large chain hold downs making it easy for those large hooks for the heavy duty trailers. Here we have a 5/8 pinhole that goes all the way through our class V, 2-1/2 inch by 2-1/2 inch receiver tube. This hitch is capable of up to 2,700 pounds of tongue weight and a 20,000-pound tow capacity. Next, we'll go ahead and give you a couple of measurements. more
8/21/2015 11:56:18 AM
Trailer Hitch Installation - 2007 Ford F-250 - Curt c14355- Video
Today, on our 2007 Ford F250, we're going to review an install. The Curt Class IV 2-inch Receiver tube 00:00:07 Hitch, part number C14355. Hi, here's what our hitch is going to look like, once installed. It's got a nice square, cross tube design, a fully welded construction, and a really nice black powdered coated finish to resist rust and corrosion. Here in the receiver tube, it's got the pre-drilled 5/8 pinhole to go all the way through and some easy access chain holdouts. 2 inch by 2 inch receiver tube, it's capable of 1,000 pound tongue capacity with a 10,000 pound tow capacity. Next we'll give you a couple measurements, this will assist you selecting accessories, such as a ball mount, bike rack, or cargo carrier. From of the center of the hitch pinhole to the outer most edge of the bumper is 5 1/2 inches. From the top of the receiver tube opening, down to the ground, is 20 inches. Now I'll go ahead and show you the minimum tools required for installing the hitch. more
8/21/2015 11:56:06 AM
Trailer Hitch Installation - 2007 Ford F-250 - Curt C15410- Video
Today on our 2007 Ford F-250, we're going to review an install. The Curt class 5, 2 inch receiver tube hitch . Part number C15410. Here's what our hitch is going to look like once installed. Our Curt extra duty hitch has a very large, square cross tube. It's fully welded construction with a really nice, commercial looking matt powder coated finish. more
8/20/2015 4:06:31 PM
Trailer Hitch Installation - 2007 Ford F-250 - Hidden Hitch- Video
Today on our 2007 Ford F-250 we're going to review and install the hidden hitch, class III, 2 inch receiver tube hitch part number 87618. Here's what a hitch is going to look like once it's installed. You've got a really nice, completely steel hitch and a fully welded construction. It's got a really nice black powder coated finish to resist rust and corrosion and blends in nicely with the under-body of the vehicle. Here, already pre-installed on the hitch, is an electrical bracket. You connect your 4, 6, or even 7 blade trailer connector to it. On either side of the receiver tube is going to be our large chain hold valves. more
8/20/2015 4:06:19 PM
Trailer Hitch Installation - 2007 Ford F-250 - Draw-Tite- Video
Today on our 2007 Ford F-250, we're going to review and install the Draw-Tite Class III 2" Receiver Tube Hitch, part number 75740. Here's what our hitch is gonna look like once it's installed. We've got a really nice completely steel hitch and a fully welded construction. Got a really nice black powder coated finish to resist rust and corrosion and blends in nicely with the underbody of the vehicle. Here already pre-installed on the hitch is an electrical bracket so you connect your four, six or even seven blade trailer connector to it. Now on either side of our receiver tube is going to be our large chain hold downs. Going all the way through the receiver tube is our 5/8" pin hole and additionally a 1/2" pin hole. more
8/20/2015 4:06:06 PM
Trailer Hitch Installation - 2007 Ford F-250 - Curt 13355- Video
Today on a 2007 Ford F250, we're going to review and install the CURT Class 3 2-inch Receiving Tube Hitch, part number 13355. Hi. Here's what our hitch is going to look like once it's installed. This is our CURT Class 3 Hitch. It's got a nice, square cross tube design to fully weld the construction and a really nice black powdered coated finish to resist rust and corrosion. Here in the receiver tube, it's got the pre-drilled 5 inaudible 00:00:28 pin hole to go all the way through. more
8/19/2015 2:26:06 PM
Trailer Hitch Installation - 2003 Ford F-350 - Curt- Video
Today on our 2003 Ford F-250 super duty we're going to take a look at and show you how to install the Curt Custom Fit Class 4 Trailer Hitch Receiver. This offers the two inch opening, it's part number is C14355. Here you can see our hitch installed in the vehicle. Really clean look, just a little bit of a step down, beefs up the rear end of the truck a little bit, at least in the looks of it. It's a really nice heavy duty hitch. This being a class four is going to give you a 1,000 pound tunge weight capacity, 10,000 pound gross trailer weight capacity. more
6/5/2015 9:52:25 AM
Trailer Hitch Installation - 2001 Ford F-250 - Curt- Video
Today, on our 2001 Ford F350 Super Duty Supercab, we're going to be installing the Curt Trailer Hitch Receiver part number C15410. Now, here's what our hitch looks like installed on our vehicle. Now, we'll go ahead and give you a couple of measurements in helping you choose some accessories for your hitch, such as a ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately 3 inches, from the top of the opening in the receiver to the ground is approximately 21 inches. Keep in mind this is a 2-wheel drive vehicle, not a 4-wheel drive vehicle. Now, let's go ahead and install our hitch. We're going to begin today's installation by first, lowering down and setting the spare tire out of the way for now. more
10/1/2014 3:57:54 PM
Trailer Hitch Installation - 2006 Ford F-350 - Curt- Video
Today on our 2006 Ford F350 we'll be installing the Curt Trailer Hitch the class five extra duty with a two inch opening part number C15410. Now here's what the hitch looks like installed on our vehicle. Now we'll go ahead and give you a couple of measurements in helping you choose some accessories for your hitch such as ball mount, a bicycle rack or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is approximately three inches and from the top from the opening in the receiver to the ground is approximately 24 inches. To begin with let's go ahead and show you the hardware that we'll be using to mount the hitch to the vehicle. All eight locations we'll be using the same hardware. We'll be using a 9/16th by an inch and three quarter carriage bolt, a square hole spacer block and a 9/16th hex flange nut. more
9/2/2014 5:08:52 PM
TorkLift SuperHitch Magnum Trailer Hitch Installation - 2005 Ford F-350- Video
Rate your transcript OrderClientKevin BrossRef #20637Order #TC1010882973 Today on our 2005 Ford F350, well be installing the Tork Lift Super Hitch Magnum Trailer Hitch Receiver, Class 5, part number TLF1002M. Heres what our hitch will look like once its installed. Next, Ill go ahead and give a few measurements that will assist you with selecting accessories, setting-up towing, or carrying with your hitch. From the center of the hitch pin hole to the outermost edge of the bumper is 2 inches, and from the top of the receiver tube to the round will be 22 inches.Now, well go ahead with our install. Step one will be identifying our attachment points. There will be total of four on each side, either pre-drilled holes in the frame by the manufacturer. The new hitch side bracket will line up with these holes. more
8/18/2014 11:19:44 AM
Trailer Hitch Installation - 1999 Ford F-350 Super Duty - Curt- Video
Rate your transcript OrderClientKevin BrossRef #20634Order #TC0837011353 Today here on our 1999 Ford F-350 Super Duty, we're going to be installing the Curt class 5 2.5 inch receiver tube hitch, part number C15810. Here's what our hitch will look like once installed. Next, go ahead and give you a couple of measurements to assist you in selecting accessories for your new hitch, such as a ball mount, bike rack, or cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper, it's 3.5 inches. From the top of the receiver tube opening to the ground is 22.25 inches. Now, go ahead with the installation. We're going to go ahead and lower and remove the spare time to make it easier to install the new hitch. All right, now we can go ahead and point out the attachment points. more
8/18/2014 10:59:06 AM
Trailer Hitch Installation - 2004 Ford F-250 - Curt- Video
Today on our 2004 Ford Super Duty, well be installing the Curt Class V - 2 Receiver Tube Hitch, part number C15410. To begin our install, well first point out the attachment points. Well have a total of 8 attachment points, 4 on each side. These holes are pre-drilled into the frame by the manufacturer. Well be using the new hardware provided with the hitch. There will be a carriage bolt and block, theyll go down through the frame, through the hitch, and get secured with a flange nut. To start, well put our rear and forward attachment point hardware in place, on both sides. Then with an extra set of hands, well go ahead and raise the hitch up into position and install the flange nut. Now that we have the hardware holding the hitch in place, well go ahead and put the other 4 fasteners in place. more
10/17/2013 12:16:36 PM
Trailer Hitch Installation - 2003 Ford F-350 - Curt C15410- Video
Today on our 2003 Ford F350, well be installing the Curt hitch, part number c15410. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is three inches, to the top of the inside of the receiver tube opening to the ground is 16-3/4. This will assist you with selecting accessories such as a ball mount, a bike rack, or a cargo carrier. Now lets go ahead with installation. Note for this application is recommended to lower and remove the spare tire for the ease installation of installing the hitch, however; unfortunately we cannot lower the spare tire as we installed this hitch.First well go ahead and identify our attachment points, there are a total of eight attachment points, four on each frame rail, these are predrilled holes in the frame rail by the manufacture. more
3/14/2013 7:36:47 AM
Trailer Hitch Installation - 2004 Ford F-250 - Hidden Hitch- Video
Today on our 2004 Ford F250 well be installing Hidden Hitch, part number 87618. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the receiver tube to the ground is 17 and a half inches. Now lets go ahead with installation. more
10/26/2012 11:46:28 AM
Trailer Hitch Installation - 2004 Ford F-250 - Draw-Tite- Video
Today on our 2004 Ford F250 well be installing the Draw-Tite hitch, part number 75740. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is five and a half inches. From the top of the receiver tube to the ground is 17 and a half inches. Now lets go ahead with installation. more
10/26/2012 11:45:48 AM
Trailer Hitch Installation - 2004 Ford F-250 - Reese- Video
Today on our 2004 Ford F250 well be installing the Reese Titan trailer hitch, part number 45297. This is what our hitch will look like once its in position. Next well go ahead and give you a couple of measurements to assist you when selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is two inches. From the top of the receiver tube to the ground is 17 and a half inches. Now lets go ahead with installation. more
10/26/2012 11:44:27 AM
Trailer Hitch Installation - 2004 Ford F-250 - Draw-Tite 41552- Video
Today on our 2004 Ford F250 well be installing the Draw-Tite Max-E-Loader trailer hitch, part number 41552. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch such as the draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is three inches. From the top of the receiver tube to the ground is 18 inches. Now lets go ahead with the installation. more
10/26/2012 11:43:44 AM
Trailer Hitch Installation - 2004 Ford F-250 - Curt 15601- Video
Today on our 2004 Ford F250 well be installing the Curt hitch, part number 15601. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch. From the center of the hitch pin hole to the outer most edge of the bumper is three and a quarter inches. From the top of the receiver tube to the ground is 17 and three-quarter inches. Now lets go ahead with installation. more
10/26/2012 11:43:07 AM
Trailer Hitch Installation - 2004 Ford F-250 - Curt 14041- Video
Today on our 2004 Ford F250 well be installing the Curt hitch, part number 14041. First well note that weve already gone ahead and lowered and removed the spare tire for an easier install. Note weve got a total of six attachment points, three on each side. These attachment points are predrilled holes in the frame by the manufacturer. The hardware well be using to attach the hitch is the new half inch carriage bolt and block and a half inch flange nut. Well first go ahead and take the carriage bolt and block and drop into the frame, which will then go through the hitch and be secured with the flange nut at each of the attachment points. more
10/26/2012 11:42:38 AM
Trailer Hitch Installation - 2004 Ford F-250 - Curt 13355- Video
Today on our 2004 Ford F250 well be installing the Curt hitch, part number 13355. This is what our hitch will look like once its installed. Next well go ahead and give you a couple of measurements to assist you with selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outer most edge of the bumper is five inches. From the top of the receiver tube to the ground is 17 and three-quarter inches. Now lets go ahead with installation. more
10/26/2012 11:42:00 AM
Trailer Hitch Installation - 2004 Ford F-250 - Curt C14355- Video
Today on our 2004 Ford F-250, well be installing the Curt Hitch, part number C14355. This is what our hitch will look like once its installed. Next, well go ahead and take a couple of measurements to assist you in selecting accessories for your new hitch such as a draw bar, a bike rack, or a cargo carrier. From the center of the hitch pin hole to the outermost edge of the bumper is 5 inches. From the top of the receiver tube to the ground is 17-3/4 inches. Now, lets go ahead with the installation. more
10/23/2012 4:19:28 PM
Trailer Hitch Installation - 2008 Ford F-250 - Curt- Video
Today on this 2008 Ford F-250, we're going to install part number C14355 from Curt. All right, this is what the hitch looks like once installed on the truck. Next, we'll go ahead and give you some measurements to help you out in selecting some accessories. From the top of the receiver opening down to the ground will be 15 inches. One thing to know about the bumper on this is the aftermarket. Basically, the hitch pin hole is ahead of the bumper by about 1-3/4 inches. more
7/31/2012 1:25:50 PM
Trailer Hitch Installation - 2006 Ford F-250 Super Duty- Video
Today we are going to install part number 41931 from Draw-Tite, and we are going to install this hitch on a 2006 Ford F-250 Super Duty. We are looking at the passengers side frame rail here, and the hitch is going to get attached at this hole here, here, here and here. And you can tell by the whole area that the original factory hitch was on there already so we already took that off. The hitch is going to attach to the same place as the factory hitch did. This one will be a lot heavier hitch. And it will be identical on both sides. The factory wiring we took and just tucked it out of the way for now during our install. We will go ahead and reinstall that after the hitch is done. more
12/28/2009 5:56:49 AM
Filter Videos
Filter Videos
