MORryde X-Factor Crossmember that Fits MORryde CRE3000 Trailer Suspension

Question

Question:

Will your UO21-015 MOR Ryde X-Factor Adjustable Crossmember fit my MorRyde CRE 3000?

asked by: John B

0

Expert Reply:

MORryde has a version of the X-Factor Crossmember that was designed to work with the CRE3000 you have with the part # MR33WR.

expert reply by: Jameson C

0

Answer 1

If you are going to install two of the MORryde X-Factor Crossmembers #MR33WR on your tandem axle trailer Alan you would want to install them on the front and rear hangers. You can install a third one if you want on the middle hanger as well for even…

view full answer...

Answer 2

We have the MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR that helps to add some extra support to the spring hangers, but aside from that the only other thing I can think of is to have a welder reinforce the brackets. I've heard…

view full answer...

Answer 3

Yes you can just use one MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR with your 2021 Jayco Jay Feather 25RB, however for full support a tandem axle trailer will need to utilize 3. Attached is a product overview…

view full answer...

Answer 4

The MORryde X-Factor Crossmember part #MR33WR attaches to the leaf spring hangers which are located in-between and in the front and rear of each axle. I have attached a photo below to clarify. Therefore, you'll need three for full support on a…

view full answer...

Answer 5

Thanks for the pictures! Since your 2022 Grand Design Reflection 303RLS came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. It looks like you have the standard 3" wide frame hanger so all of the…

view full answer...

Answer 6

The MORryde X-Factor Crossmember for Standard Frame Hangers #MR33WR includes new wet bolts for the hangers on your 2022 Keystone Montana High Country 351BH 5th wheel camper. So you will not loose the ability to grease your hanger bolts.

view full answer...

Answer 7

The MORryde X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR includes one adjustable crossmember. Your existing hardware will be too short due to the extra thickness of the crossmember, so you will need to add #MR58ZR if…

view full answer...

Answer 8

The correct hub and drum assembly replacement for your Lippert 4,400 lb axle is the #8-407-5UC3-EZ. This comes with bearings and a grease seal. If you need brakes as well you can use the #LC66WD, or for self-adjusting brakes #K23-478-479.

view full answer...

Answer 9

The MORryde X-Factor Crossmember part #MR33WR is designed for standard suspension so that is the one you will need to use. If your leaf spring hanger brackets are wider than 3" then you will need to drill per the instructions which I have…

view full answer...

Answer 10

Since your Grand Design came with the CRE3000 equalizers you will need three of the MORryde X-Factor Crossmember item #MR33WR. All of the hardware is included. I have linked an installation video below.

view full answer...

Answer 11

I went ahead and reached out to my contact at MORryde, and she confirmed that the X-Factor Crossmember for CRE, SRE, or Stock Leaf Spring Suspension #MR33WR will come with new mounting hardware. The plates on the cross member do add thickness, so the…

view full answer...

Answer 12

For absolute best results you'd install three of the MORryde X-Factor Crossmember for LRE, RE, or TRE Leaf Spring Suspension #MR99ZR but some people will use just two on a tandem setup and it will work great. If you check out the install…

view full answer...

MORryde X-Factor Crossmember that Fits MORryde CRE3000 Trailer Suspension

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching