Expert Review Video:
Tube Step Specs:
Features:
These straight-style, extra-wide step bars give your vehicle a rugged look. The oval, polished stainless steel bars have molded plastic endcaps to keep out moisture. Oversize, 5" wide step pads provide sure footing. Mounting kit is included.
Installation Notes:
No drilling required for installation
More Information >Tube Step Specs:
Features:
Straight-style step bars with wide, top-mounted, non-slip pads give your vehicle a rugged look. The 4" wide oval bars are made of black powder coated steel and have molded endcaps to keep out moisture. Custom, no-drill mounting kit included.
Installation Notes:
No drilling required for installation
More Information >Tube Step Specs:
Features:
These straight-style, extra-wide step bars give your vehicle a rugged look. The oval, black powder coated steel bars have molded plastic endcaps to keep out moisture. Oversize, 5" wide step pads provide sure footing. Mounting kit is included.
Installation Notes:
No drilling required for installation
More Information >Tube Step Specs:
Features:
Straight-style step bars with wide, top-mounted, non-slip pads give your vehicle a rugged look. The 4" wide oval bars are made of polished stainless steel and have molded endcaps to keep out moisture. Custom, no-drill mounting kit included.
Installation Notes:
No drilling required for installation
More Information >Videos
for Nerf Bars - Running Boards
Help Articles
for Nerf Bars - Running Boards
Expert Answers
for Nerf Bars - Running Boards
The 40 amp fuse for your 2006 Chevrolet Silverado tow package is used for the 12 volt battery charge circuit. This fuse is located toward the front of the underhood fuse box closest to the front auxiliary positive post (see photo). There may be a…
view full answer...On a 2005 Chevy Silverado 1500, If you are facing the front of the truck looking at the power distribution box, there will be a post at the back left side and a fuse slot near it. It is that fuse slot that you will install a 30 amp fuse. I have…
view full answer...The number you provided, "7753400" is a patent number which…
view full answer...The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…
view full answer...For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…
view full answer...If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…
view full answer...The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x…
view full answer...The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the…
view full answer...It sounds like the 2022 Chevy Silverado 3500 you are getting has the short bed. In that case, yes, you definitely want the sliding 5th wheel hitch for clearance. The good news is you will not need to purchase the entire…
view full answer...Based on the information you gave, although I can't help with the axle (other than to state it is a 3,500 lbs axle). Dexter mobile home axles were designed for…
view full answer...Below is the general process for bleeding an electric over hydraulic brake actuator like #K71-650. Fill reservoir with NEW brake fluid. Never re-use brake fluid that has been salvaged or removed from another system. Remove the key from the…
view full answer...To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…
view full answer...Filter Products (8)
Contact and Help
What our customers are saying:
Very helpful/friendly Customer Service. Competitive Pricing. Shipping was Fast.
John
Mankato, MN