Are Wiring Plug-Ins Needed for Optronics Trailer Tail Light # STL211RB

Question

Question:

Do I need to order plugs for this light? In the pictures it looks to have a dual plug on the rear.

asked by: Jimmy

0

Expert Reply:

Yes, wiring pigtails will be needed in order to install the Optronics Trailer Tail Light, # STL211RB.

For straight pigtails you will need the 3-wire, # A45PB, and 2-wire, # A45CB.

For right angle pigtails you will need the 3-wire, # A47PB, and 2-wire, # A49PB.

expert reply by: Leah S

0

Answer 1

For the Fusion LED Trailer Tail Light - Stop, Tail, Turn, Backup part #STL211RB you will use the Right Angle 3-Wire Pigtail for Optronics Trailer Lights part #A47PB for the three wire which will carry your running lights, turn/brake signal lights and…

view full answer...

Answer 2

You would need to have a reverse light circuit ran to your trailer to power reverse lights. If you have a 5-way flat or 7-way trailer connector currently then that circuit is already present. If you have a 4-way harness then you would need to install…

view full answer...

Answer 3

I went out to the warehouse and pulled the Optronics #STL201RFMB light to test it out and see for you. I found that when you have the running lights on that the LED ring glows constantly. When you press the brake, the red LEDs and the red LED ring…

view full answer...

Answer 4

We do have a solution for you, however, you will not be able to power reverse lights on a trailer with a 4-pin trailer connector. The reverse lights on a trailer must receive power from the reverse lights on the tow vehicle. To do this, you will want…

view full answer...

Answer 5

To connect back up lights you need to have a 7-way trailer connector on both your trailer and tow vehicle. On a 7-way the reverse lights are powered by the center pin. To connect reverse lights to the trailer's 7-way you can use 16 gauge wire…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 8

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 12

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Are Wiring Plug-Ins Needed for Optronics Trailer Tail Light # STL211RB

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching