Can the Dexter Trailer Axles # T20BTR-EZ-6048 have the Spring Seats Moved to Top of Axle

Question

Question:

I have a harbor freight trailer that has a bent axle, I am trying to find a replacement and I think that the Dexter Trailer Idler Axle Beam with EZ-Lube Spindles - 60inch Long - 2,200 lbs will work, but I need the spring seats to be over slung. I need the extra height for clearance. Do you sell your axles with this option?

asked by: Dan K

0

Expert Reply:

We don't sell the Dexter Trailer Axles # T20BTR-EZ-6048 with the spring seat on top of the axle so that it could be installed overslung. But, what you can do is get the # TRSS175 and then have a qualified welder install this spring seat on the top of the axle so that you could install it in the configuration you need to.

expert reply by: Jameson C

0

Answer 1

Yes, the Timbren Silent Ride Suspension Systems like part #TSR2000S03 require a crossmember installed between driver and passenger side. The crossmembers is needed to add additional support. It will be welded to the back of the flange which you can…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 4

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 5

For a single axle trailer, you want the shackle strap to be able to move so that you have the spring deflection needed for your suspension. Angled like the photo or even almost vertical is fine you just don't want the shackle strap to bind and…

view full answer...

Answer 6

Well shackle length is mainly based on the height difference between the front and rear hangers. The rear hanger normally doesn't hang as low as the front so that the shackle can offset the difference and add the ability to move. What is the…

view full answer...

Answer 7

I have attached for you below some common torque values needed for a trailer suspension system but a lot of these will vary by bolt size and other factors. U-Bolts: Varies by Size - 1/2" bolts: 45 ft/lbs - 70 ft/lbs, 9/16" bolts: 65 ft/lbs…

view full answer...

Answer 8

To correctly measure a leaf spring, you'll want to jack the trailer up on jack stands so the axle is hanging freely, then measure directly across from the center of one spring eye to the other, as shown in the provided diagram. The height of the…

view full answer...

Answer 9

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Can the Dexter Trailer Axles # T20BTR-EZ-6048 have the Spring Seats Moved to Top of Axle

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching