Can the CE Smith Keel Roller Assembly Be Installed at Various Angles

Question

Question:

When this part is installed can you set it at any angle or does it have to be like in the picture? I wanted to use it as a bow stop but my winch post is straight up with no angle.

asked by: Justin

0

Expert Reply:

The CE Smith Keel Roller Assembly # CE32005G that you referenced is designed with several installation holes in the brackets so that various angles and heights can be used for installation.

Check out the review video I attached for more info.

expert reply by: Jameson C

0

Answer 1

The CE Smith Keel Roller Assembly for 2-Inch Wide Trailer Tongues, part #CE32005G, has multiple mounting holes to allow it to fit on a 2-inch trailer tongue at any of 4 or more different heights depending on how it is oriented. Please refer to the…

view full answer...

Answer 2

First, roller with bracket #CE32100G is not going to work because the mounting holes on it are spaced 3 inches apart on center so it would be too wide. It measure approximately 2-1/2 inches from the bottom of the bracket to the center of the shaft.…

view full answer...

Answer 3

Yes, you can absolutely drill holes in your trailer tongue to install the 10,000 lb capacity Buyers Products Straight Tongue Trailer Coupler #3370091560. This is a pretty common occurrence due to the various bolt hole patterns of straight tongue…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

By "mobile home type bolt pattern" I believe you are talking about a 5 spoke utility bolt pattern such as what is on the Dexter Trailer Hub and Drum Assembly - 6,000-lb and 7,000-lb Axles #8-174-5UC3. To measure your axle from hub face to…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

I agree it is the right time to upgrade to a Lithium charger/converter as not all are Lithium compatible. I recommend using the Progressive Dynamics Mighty Mini AC/DC Panel and Converter/Smart Charger - 60 Amp #PD4060K which is a replacement for your…

view full answer...

Answer 8

If your old axles have a 5 bolt brake flange the assemblies like Dexter Electric Trailer Brake Assembly - 12" - Left Hand - 6,000 lbs part #23-105 or Dexter Electric Trailer Brake Assembly - 12" - Right Hand - 6,000 lbs part #23-106 will…

view full answer...

Answer 9

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

For all intents and purposes, yes, the Fulton drop leg stabilizer jack SJL80300 is the same as the square leg jack you asked about: - Square Drop Leg Stabilizer Jack - 18" Travel - 2,000 lbs #SJ-R208 Different manufacturers but otherwise they…

view full answer...

Answer 12

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Can the CE Smith Keel Roller Assembly Be Installed at Various Angles

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching