Ramp Door Lock Assembly Recommendation for an Enclosed Trailer

Question

Question:

Hello, I need a cam door lock for the rear ramp of my enclosed cargo trailer, but it needs to be mounted on the rear corner side. Will this swivel 270 deg from the mounting plane? If not, can you tell me which cam door lock will work? Thanks.

asked by: Andy

0

Expert Reply:

If you were to mount the 36" Lock Side-Door Bar Lock Assembly # 305736 on the edge of the corner of your trailer the handle could swing around the corner beyond 180 degrees as there is not a stop in the hinges of the lock. So yes, this could swing 270 degrees from the mounting plane so it should work well for you.

expert reply by: Jameson C

0

Answer 1

Installing the Hinges on your Side-Door Bar Lock Assembly, item #305736, is pretty much up to you and the construction of your trailer. You will need to purchase appropriate hardware to install the Side-Door Bar Lock that you purchased. It is best…

view full answer...

Answer 2

You would need to use the Universal Cam-Door Lock for Enclosed Trailers, item #383200, to create a bar lock assembly of 55 inches. With this item you supply the 3/4 inch inside diameter pipe to make a custom door lock. Some welding is required for…

view full answer...

Answer 3

Lippert unfortunately doesn't have a simple installation manual for the Lippert Replacement Hydraulic Power Unit with 2-Quart Pump Reservoir Kit for RV Slide-Out IRC System #LC141111, but I was able to find a wiring diagram to show how the…

view full answer...

Answer 4

I have attached some diagrams of the wiring for the Lippert Replacement Hydraulic Power Unit with 2-Quart Pump Reservoir Kit for RV Slide-Out IRC System #LC141111. The first one is from my contact at Lippert and some of the extra wiring is from…

view full answer...

Answer 5

I have a solution for you but you will need to supply your own pipe to get your desired 33-1/4 inch size. The Universal cam-door lock with 1 inch keeper #383200 will allow you to create a bar lock assembly of 33-1/4 inches. With this item you…

view full answer...

Answer 6

The Curt SecureLatch Lunette Ring with 8-Position Adjustable Channel #CU49FR does come with the hardware needed to attach the lunette ring to the channel. It is 3 bolts, 3 nuts and 6 washers. The picture below shows every piece you would receive.…

view full answer...

Answer 7

The best option we can offer you is the Trailer Idler Hub Assembly part #AKIHUB-545-2-EZ-2K which will be a direct replacement for the Dico Trailer Hub Assembly part 45263 so long as you the Double Lip Grease Seals part #RG06-010. The Trailer Idler…

view full answer...

Answer 8

The best way to identify the seal needed, is to get the number that is stamped or imprinted on the seal. You may have to remove the seal in order to see the numbers. If you cannot find the number on the seal, if you can find the numbers on the inner…

view full answer...

Answer 9

The keeper and lug of the part #PLR158 are the two pieces that mesh together to hold the door shut like you mentioned. The handle of this gets welded to the bar. I attached a review video for this for you to check out as well.

view full answer...

Answer 10

The Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers #305736 from Polar is the same thing as the Redline 305736 like what you're asking about. I'm not sure why the name change but it has the same specs as you can see in…

view full answer...

Answer 11

While we do not have any spacers for the Cam-Action Lockable Door Latch #305736 they can easily be made using steel plate from a local steel supplier or hardware store.

view full answer...

Answer 12

We have multiple options in 12', 18' and 24' lengths. My recommendation is the Small Coin Pattern, #TS67FR at 18' length with additional 12' from the #TS57FR. For wood flooring, use either RV Flooring Adhesive for Vinyl Over Wood,…

view full answer...