Longer Roller Shaft Recommend to Install Endcaps on CE Smith Deep V Keel Roller Assembly # CE10405G
Question:
I bought CE Smith Deep V Keel Roller Assemblies CE10405G and I got these end caps too but I was told that we need a longer shaft to fit this end cap? I got everything from your website and it didnt mention anything about a longer shaft needed. Could you provide a solution to be able to attache these end caps to keep roller assembly? Thank you for your assistance.
asked by: Guven Y
Expert Reply:
To install the endcaps part # YR134-5 on the ends of the roller of the CE Smith Deep V Keel Roller Assembly # CE10405G you will need to get a longer 5/8 inch shaft so that there is enough room for the endcaps to secure on either side of the bracket.
The roller shaft that would most likely work the best for you would be the 19 inch 5/8 inch diameter roller shaft # 107-30A. You will need to measure your setup to be sure this would work for you though.
Products Referenced in This Question
Roller Shaft w/Cap Nuts 19" x 5/8"
- Boat Trailer Parts
- Rollers
- Roller Shafts
- 5/8 Inch Diameter
- Zinc-Plated Steel
- 19 Inch Long
- CE Smith
more information >
CE Smith Deep V Keel Roller Assembly for Boat Trailers - Galvanized Steel/Black Rubber - 12"
- Boat Trailer Parts
- Rollers
- Keel Roller
- Black Rubber
- 12 Inch Long
- CE Smith
more information >
Product Page this Question was Asked From
Yates Endcap for Boat Trailer Rollers - Heavy-Duty Rubber - 5/8" Shaft - Qty 1
- Boat Trailer Parts
- Rollers
- End Cap
- 1-1/4 Inch Wide
- 3-1/2 Inch Diameter
- Black Rubber
- Fits 5/8 Inch Shaft
- Yates Rubber
more information >
Continue Researching
- Shop: Easy Grease Trailer Idler Hub Assembly for 2K Axles - 4 on 4 - Galvanized
- Shop: Trailer Idler Hub Assembly for 2,000-lb Axles - 4 on 4 - Galvanized
- Shop: Channel Tongue Trailer Coupler - Trigger Latch - Zinc - 2" Ball - Bolt On - 3,500 lbs
- Video: Review of CE Smith Boat Trailer Parts - Roller and Bunk Parts - CE29505
- Video: CE Smith Boat Trailer Parts - Roller and Bunk Parts - CE10500G Review
- Video: CE Smith Boat Trailer Parts - Roller and Bunk Parts - CE10405G Review
- Q&A: Dimensions of CE Smith Deep V Keel Roller Assembly CE10405G
- Q&A: Roller Capacity of CE Smith Deep V Keel Roller Assembly for Boat Trailers
- Search Results: keel roller bracket
- Search Results: side guide roller
- Search Results: boat trailer steps
- Shop: CE Smith Universal-Fit Split Panel Brackets for Boat Trailers - Galvanized Steel - 1 Pair
- Shop: Yates Bow Bell for Boat Trailer Rollers - TPR - 4-1/2" Diameter - 1/2" Shaft - Black
- Shop: Roller Shaft with Pal Nuts for Boat Trailer Rollers - Zinc-Plated Steel - 12-3/4" x 1/2"
- Shop: Roller Shaft with Pal Nuts for Boat Trailer Rollers - Zinc-Plated Steel - 13" x 5/8"
- Search Results: boat trailer winch strap
- Q&A: How to Convert Oil Bath Trailer Hubs to Grease Hubs
- Video: Review of Yates Rubber Boat Trailer Parts - Blue Endcap For Boat Trailer Rollers - YR131-4B
- Shop: Trailer Hitch
- Q&A: How to Tell if Trailer has a BT8 or BTR Spindle Installed
- Article: Most Popular Wheel Bearings
- Search Results: 25580
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Video: etrailer Trailer Idler Hub Assembly Review and Installation
- Shop: Trailer Wiring
- Article: Trailer Tire Sizing
- Search Results: bearing buddy
- Search Results: l44649
- Shop: Brake Controller
- Q&A: What Is the Difference Between a BTR and BT8 Spindle