Trailer Brakes Get Stuck and Overheat
Question:
I have a 2002 Ford Explorer and Prodigy P2 that is 15 years old. Yesterday, I had to tow our enclosed trailer for the first time since December. It has electric brakes on all 4 wheels. It is a torsion axle setup, Dexter I believe. I noticed it was towing much harder than normal. I always use the manual lever for a few slow speed brake engagements at slow speed on the way to the highway. I noticed the brakes came on but then delayed releasing. I thought sitting might have caused the brakes to stick some but since it is electric brakes Im not sure sticking could be an issue. Even after several manual actuations and even holding the lever over slightly for several seconds, it kept feeling like a delayed brake release. I think I noticed a couple of times that a number was in the display vs. the .C display like the brakes were being turned on while going down the road at a steady speed. When I stopped I noticed that burning smell, all 4 trailer wheels were very warm to hot and even the sidewalls of the tires had a lot of extra heat. Does this sound like a controller issue or trailer brake issue?
asked by: Bruce
Expert Reply:
The P2 # 90885 has not been around for 15 years. You might have the original Prodigy # 90185. The sure way to know is the display. If the display is blue, its a P2. If the display is red, it is a Prodigy.
There are a lot of moving parts in electric drum brakes. They could get stuck if the return springs are bound up or corroded or if something needs some lubrication.
Nine times out of ten, it is a brake issue. But it could be electrical further back than the brake controller. The first thing you will want to do is make sure the vehicle and trailer side connectors are clean and free of corrosion on the pins and inside where the wires attach.
Inspect the wiring from the trailer side connector back to the magnets. Look for frayed or pinched wires. This would cause a short and some constant power draw. You can also visually inspect the magnets and if you can see the copper windings coming through the magnets will need to be replaced.
You can visually inspect the magnets and if you can see the copper windings coming through the magnets will need to be replaced. To further test the magnets you can follow the help article I have linked.
Since the brakes got so hot you will want to pull the drums off and inspect the insides of the drums where the magnets attach, called the armature surface. If the armature surface is discolored you will need to replace the drums.
While you have the hubs off you can check the brake assemblies to determine if the shoes need to be replaced or if any of the moving parts are bound up or look like they need to be replaced.
Product Page this Question was Asked From
Tekonsha Prodigy P2 Trailer Brake Controller - 1 to 4 Axles - Proportional
- Trailer Brake Controller
- Proportional Controller
- Electric
- Electric over Hydraulic
- Automatic Leveling
- Under-Dash Box
- Dash Mount
- Up to 4 Axles
- LED Display
- Up to 360 Degrees
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Hopkins Engager Push-To-Test Trailer Breakaway Kit w/ Built-In Charger - Side Load - 7" Wire
- Q&A: How to Reset a Breakaway System After Pulled Pin
- Q&A: Troubleshooting Electric Trailer Brake Assembly That is Running Hot
- Q&A: Potential Causes for Trailer Hub to Heat Up
- Q&A: Troubleshooting Trailer Brake Drum Heat Build-Up on One Hub of Boat Trailer
- Q&A: Troubleshooting Trailer Brakes Where Only One Assembly Is Getting Hot
- Q&A: Potential Causes for Overheating Trailer Brake Drums
- Article: How to Adjust Your Trailer Brakes | The Ultimate Guide
- Shop: Brake Controller
- Video: Trailer Brakes and Wiring Installation
- Q&A: Troubleshooting Trailer Brakes Where One Wheel Locks Up
- Shop: Brake Adjustment Spoon for Drum Brakes
- Shop: Dexter Trailer Hub and Drum Assembly for 3,500-lb E-Z Lube Axles - 10" Diameter - 5 on 5-1/2
- Search Results: dexter 8 247
- Video: Trailer Hitch Installation - 1999 Ford Ranger - Curt
- Shop: Hayes Engage Trailer Brake Controller - 1 to 3 Axles - Time Delayed
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class III - 2"
- Shop: Roadmaster Stop Light Switch Kit - Chevrolet Equinox / GMC Terrain
- Shop: Roadmaster Stop Light Switch Kit
- Shop: Trailer Hitch
- Shop: Vehicle Tow Bar Wiring
- Shop: Vehicle Tow Bar Brake System
- Search Results: 39523
- Video: Choosing the Right Brake Controller
- Search Results: norcold refrigerator vent screens
- Search Results: ac units
- Search Results: brake controller
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Video: Choosing the Right Trailer Wiring
on Trailer Brake Controller
