Will the Air Lift Ride Control Air Helper Springs # AL59516 fit a 2WD 2003 Ford Ranger Edge

Question

Question:

Will this fit the 2003 2wd Edge ext cab model? Thanks

asked by: Damien

1

Helpful Expert Reply:

Yes, I checked with Air Lift and the Air Lift Ride Control Air Helper Springs # AL59516 that you referenced have been confirmed to fit the 2 wheel drive Edge model 2003 Ford Ranger that you have so this kit will work great for you.

You might also be interested in the compressor kit part # AL25592 to make inflating the kit as easy as pressing a button.

expert reply by: Jameson C

1

Answer 1

The Air Lift Air Suspension kit part #AL59516 that you referenced has been confirmed as a fit for your 2000 Ford Ranger so it would work well for you. You are supposed to always have a minimum of 5 psi in the bags at all times so there is no reason…

view full answer...

Answer 2

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 6

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 7

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 8

I checked with Curt and they do show the Curt Trailer Hitch Receiver part #C13233 as a fit for a 2022 Volvo XC90 All Models which includes the Recharge.

view full answer...

Answer 9

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 10

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 11

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 12

Replacement arms are available for the Roadmaster EZ5 Base Plate Kit #RM-521569-5 for your 2015 Honda Fit with the part #RM-ARMS. When the original base plate brackets and arms were manufactured, they were made as one part. To be sure that the new…

view full answer...

Will the Air Lift Ride Control Air Helper Springs # AL59516 fit a 2WD 2003 Ford Ranger Edge

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching