How to Find the Right Replacement Wobble Roller for a 2006 Magic-Tilt Trailer

Question

Question:

have an 06 magic-tilt trailer. Do your wobble rollers work as replacements on my 06? Thanks

asked by: Mark H

1

Helpful Expert Reply:

There are only a few rollers that we carry that list specific trailers that they will fit. For everything else, you will need to go by the dimensions of the roller to determine if it/they will fit your trailer. I have included a link to the wobble rollers we carry to the right.

Or if you can tell me the overall diameter, width, and the shaft size of the existing rollers I can make some recommendations for you.

expert reply by: Michael H

1

Answer 1

We carry boat trailer hardware though not all parts for the Yates Ribbed Wobble Roller 5" Diameter #YR500YW-6P. We do offer Wobble Roller Washer for 3/4" Shaft #CE10983 and Wobble Roller Retainer Ring #CE10981. I have added a link for you…

view full answer...

Answer 2

We have a 5 inch diameter Yates Wobble Roller that fits a 3/4 inch diameter shaft. For that you'd need the #YR500YW-6P and you'd be set.

view full answer...

Answer 3

If you have enough of the shaft still intact then you can use the CE Smith Wobble Roller Retainer Ring #CE10981 and a Wobble Roller Washer #CE10983 for the Yates Ribbed Wobble Roller #YR343R-6P for a 3/4" shaft. Otherwise you may need to get a…

view full answer...

Answer 4

Yes you can go to a larger diameter wobble roller very easily by just replacing what you have with one that has all dimensions matching except outer diameter. The part #YR500YW-7P has an outer diameter of 5 inches, a width of 3 inches and a shaft…

view full answer...

Answer 5

Taking the retainer ring like part #CE10981 out when removing a wobble roller can be tricky, particularly when they tend to break. My best recommendation is to use two needle nose pliers if you can get a good grip when removing the ring. You can grab…

view full answer...

Answer 6

The only wobble roller that we have which fits a 1" shaft and doesn't have a 5" diameter is the CE Smith #CE29539. This wobble roller has a 4-1/4" diameter and measures 3" wide. If you need it to have a larger diameter than…

view full answer...

Answer 7

You need the Yates Ribbed Wobble Roller #YR500YW-8P. It matches your roller at 5" in diameter, 3" wide and uses a 1-1/2" long bushing to fit on a 1" shaft. The Washer For 1" Spindle #SW1000 are sold individually so be sure to…

view full answer...

Answer 8

Since your main concern is the marks on the hull of your boat I recommend going to the Yates TPR Ribbed Wobble Roller. These rollers are constructed of thermal-plasticized rubber which is a non-marking, non-scratching material. It is stronger and…

view full answer...

Answer 9

Yes, the Yates Ribbed Wobble Roller for EZ Loader Boat Trailers #YR500YW-8PEZ that you referenced would easily handle the weight of your 6,000 lb boat since you'd be using 32 of them.

view full answer...

Answer 10

Sounds like you are looking for a way to secure the #CE10981 to the shaft for the installation of the part #YR343R-6P. A decent set of pliers like the part #PTW88003 would do the trick. Or a set of channel locks.

view full answer...

Answer 11

I went out to the warehouse and pulled Yates boat roller #YR500YW-6P. The inside width where the shaft goes is 1-1/2 inches. I have included a link to a video review of this roller for you. Some related items you may also need are the retainer ring,…

view full answer...

Answer 12

The Yates Ribbed Wobble Roller, #YR500YW-8PEZ, is exactly what you need for your 1999 EZ Loader boat trailer. The bushings are included with this roller. For a hog ring, we offer part #CE10981 and you can use part #SW1000 for a washer. At this time,…

view full answer...

How to Find the Right Replacement Wobble Roller for a 2006 Magic-Tilt Trailer

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching