Replacement Wobble Roller Needed with 1 Shaft for Older Boat Trailer

Question

Question:

trying to find wobbler roller to match my easy load boat trailer. wobbler measures 4 3/8 od x 2 3/4 wide x 1inch shaft od. but I cant seem to find that measurement. 1 in shafts seem to be 5 inch od, which is not a match. I used calipers to measure. any help finding right wobbler. I dont have manual to look up. boat is 92 Larson xl180

asked by: Doug

0

Expert Reply:

The only wobble roller that we have which fits a 1" shaft and doesn't have a 5" diameter is the CE Smith # CE29539. This wobble roller has a 4-1/4" diameter and measures 3" wide. If you need it to have a larger diameter than 4-1/4" then you need to bump up to the 5" diameter like the Yates Ribbed Wobble Roller for EZ Loader Boat Trailers # YR500YW-8PEZ. If you still have the original rollers on your boat trailer and the trailer is as old as your boat then it is entirely possible that the roller has worn down some over the past almost 30 years which is why the diameter seems to be such a difference.

Attached are some review videos that you can check out as well.

expert reply by: Jon G

0

Answer 1

Yes, the Yates Ribbed Wobble Roller for EZ Loader Boat Trailers #YR500YW-8PEZ that you referenced would easily handle the weight of your 6,000 lb boat since you'd be using 32 of them.

view full answer...

Answer 2

We carry one wobble roller, #YR500YW-8PEZ, that is specifically found on EZ Loader Boat Trailers. It is possible that other replacement parts would fit but as far as manufacturers specifically calling out EZ Loader trailers this roller is all we…

view full answer...

Answer 3

Taking the retainer ring like part #CE10981 out when removing a wobble roller can be tricky, particularly when they tend to break. My best recommendation is to use two needle nose pliers if you can get a good grip when removing the ring. You can grab…

view full answer...

Answer 4

There are only a few rollers that we carry that list specific trailers that they will fit. For everything else, you will need to go by the dimensions of the roller to determine if it/they will fit your trailer. I have included a link to the wobble…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Seal 171255UC has an inner diameter of 1.719 inches and outer diameter of 2.565 inches. A seal that has those dimensions would actually be #58846. I've added a link to a video review of this seal for you to take a look at.

view full answer...

Answer 9

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 10

If the trailer wheels scrubbed (dragged and scrapped the ground instead of rolling) when jack knifed then it could have thrown something out of alignment or damaged something. First, inspect the suspension. Look for any elongated holes where…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Replacement Wobble Roller Needed with 1 Shaft for Older Boat Trailer

Products Referenced in This Question

Featured Help Information

Miscellaneous Media

Continue Researching