Seal # 168233 and Race # L68110 Availability

Question

Question:

After buying what I thought were the right bearing kit for my boat trailer, I found your site and after reading the info you provide, I now need different races and seals. 68111 will not fit my hub. 68110 will. Needs seal 168233. Ordering now. Thank you!

asked by: Lance

0

Expert Reply:

Glad we were able to help! And that you got the correct Seal # L68110 and Seal # 168233.

expert reply by: Jameson C

0

Answer 1

Having a 1.25 spindle, it can be a few bearings that will fit. However, there will not be a hub that uses both an inner and outer bearing of this size. With that said, I highly recommend replacing your axles with something that will use a more common…

view full answer...

Answer 2

The difference between the L44649 and the L44649R is not the size of the race used as you have found. Typically the R indicates that the bearing was used in a higher capacity application. Dimensionally the bearings are the same and would take the…

view full answer...

Answer 3

When the L68149 bearing is paired with the L68111 race, the 10-19 grease seal is used. However when the same bearing is used with the L68110 race on a boat trailer, the #168233 seal is usually used. You can verify this by using a digital caliper to…

view full answer...

Answer 4

The Lippert Components Heavy-Duty Replacement Shock - Yellow #LC283280 is 8.625 inches compressed and 13.5 inches fully extended. Your current suspension may extend and retract slightly further but the shocks will be a good replacement based on the…

view full answer...

Answer 5

From the picture you sent in it looks like the Dexstar Vintage Steel Wheel #AM20395 15" x 5" is what you are looking for. These have a 4 on 9.44" bolt pattern which you can verify matches what you have by measuring from the center of…

view full answer...

Answer 6

Yes, the Typical Axle Diameters Based on Axle Capacity are as follows: 1,000-lb - 2,000-lb Axles: 1-1/2 inch - 1-3/4 inch diameter 3,500-lb Axles: 2-3/8 inch diameter 5,200-lb - 7,200-lb Axles: 3 inch diameter If you have a 3" diameter axle then…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

From the numbers you provided it sounds like you need replacement grease seals. In my research, the grease seals I found with the GS-1719DL number have a 1.72 inside diameter and 2.565 outside diameter. The replacement double lip grease seals you…

view full answer...

Seal # 168233 and Race # L68110 Availability

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching