How to Install the Wheel Masters 4-Hose Inflation Kit on a 2013 Chevrolet Silverado Dually

Question

Question:

I have a 2013 Silverado Dually with stock stainless wheels and the hub covers with the black plastic lug nuts. Will this product work? How would the hoses get mounted to the hub cover? I see pop rivets in the picture. Is that how the brackets would hook up?

asked by: Mike L

0

Expert Reply:

There are two ways to mount the Wheel Masters Inflation Kit, # WM8001. You can use the pop rivets to attach the L-brackets to the hub cover or you can use the flat brackets to attach them to an axle housing bolt. These are not a vehicle specific item and they were designed to fit 16 inch to 19-1/2 inch dually wheels.

Check out the installation instructions I attached for this product. Since your truck has the hub covers, your best option would be the L-brackets. You will need a 1/8 inch drill bit for the rivets and each L-bracket will require 2 rivets.

expert reply by: John H

0

Answer 1

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 2

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 11

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 12

Load range B trailer tires are going to have a lower capacity than C load range tires. Basically that, psi rating, and the ply rating are the only differences. A higher load range tire would last a little longer than lower load ranges of the same…

view full answer...

How to Install the Wheel Masters 4-Hose Inflation Kit on a 2013 Chevrolet Silverado Dually

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching