Mounting Bracket Recommendation for a Bulldog Round Swivel Jack # BD154107

Question

Question:

IM TRYING TO INCORPORATE THE BD154107 INTO MY DESIGN. IS THERE A MOUNTING BRACKET AVAILABLE FOR THIS MODEL? IF SO, PLEASE ADVISE...NEED ZINC PLATED. THANKS!

asked by: GARY

0

Expert Reply:

The correct mounting bracket for the Bulldog Round Swivel Jack # BD154107 is the Jack Mounting Bracket # P9012-00. It's not zinc plated though because it is designed to be welded to a trailer and when you weld something zinc plated it gives off toxic fumes.

expert reply by: Jameson C

0

Answer 1

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex…

view full answer...

Answer 2

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you,…

view full answer...

Answer 3

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 4

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 5

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 6

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 7

To determine which brake assemblies would be needed, you will need to measure your existing brake drums as shown in the provided photo. Since your trailer has a 14,000 lb capacity, you most likely have tandem 7,000 lb axles, which typically use a…

view full answer...

Answer 8

Yes, the best option we can offer you to add fuel capacity is with the DeeZee Truck Bed Auxiliary Tank part #DZ91752X which should fit in the space you have between the cab and 5th wheel hitch no problem as it is only 9" deep. I don't have…

view full answer...

Answer 9

As far as height adjustability and weight capacities the Curt Q20 #C16130 and the Curt A20 #C16140 are identical. They both have a Gross Towing Weight of 20,000 lbs, a Vertical Load Limit of 5,000 lbs, and a height range of 13-17 inches. When it…

view full answer...

Answer 10

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 11

I'm assuming your Express doesn't have the 7-way, but does have the capped round plug behind the bumper on the drivers side frame rail, you'll install part #30955. Simply remove the cap and plug the connector in. To wire up the controller…

view full answer...

Mounting Bracket Recommendation for a Bulldog Round Swivel Jack # BD154107

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching