Will Grease Cap Plug Part RG04-010 Fit Tie Down Engineering SuperLube Grease Caps

Question

Question:

Will these fit a sup-r-lube tie down system?

asked by: Greg

0

Expert Reply:

We do not carry the Tie Down Engineering hubs and caps, so I could not check for sure if they would fit the Tie Down Super Lube grease caps.

I did get the measurements for the plugs and they will fit a 1-1/4 inch opening on a grease cap. If the opening for your SuperLube caps is 1-1/4 inch in diameter, then these plugs will fit fine.

expert reply by: Patrick B

0

Answer 1

Yes, the #RG04-010 grease cap plugs are a great fit for the 1.986 inch outer diameter #RG04-040 grease caps.

view full answer...

Answer 2

You would need to measure the inside diameter of the hub opening to determine which cap size is needed. You would want to choose a cap whose outside diameter matches the inside diameter of the hub. Some of the most common sizes are 1.980 inch, 1.986…

view full answer...

Answer 3

The #RG04-010 are designed for use on EZ Lube spindles and hubs, which it sounds like what you're referring to with the grease zerk at the center of the hub. It might be a close fit with the cap, but as long as everything is seated properly on…

view full answer...

Answer 4

The part #RG04-010 is designed to fit a 1.18 inch grease cap center hole. If you measure yours and it matches that then these are the correct ones. It's hard to say if the amount of play you mentioned is acceptable but you do want to them to seal…

view full answer...

Answer 5

The center portion of the Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 is designed to allow the grease to expand slightly when warm and not pop the cap off. If you are seeing it pop out when cold you may have too much grease in the hub. I'd…

view full answer...

Answer 6

The Grease Cap Plug for E-Z Lube Grease Caps #RG04-010 will replace your missing rubber cap on your Dexter E-Z lube axle hub.

view full answer...

Answer 7

Because the zerk fitting is a press fit, if they are falling out I would recommend simply leaving them out and replacing your existing grease caps with bearing protectors like Bearing Buddies. The Bearing Buddies you need will depend on your hub…

view full answer...

Answer 8

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

A tow package for a vehicle is usually a frame mounted trailer hitch and trailer wiring on a vehicle like your 2002 Dodge Dakota. If you have those two things you could pretty easily assume you have the tow package. Or, you can take the VIN of your…

view full answer...

Answer 12

The Replacement Amber Lens for MC32AB Trailer Lights #A32AB is a direct replacement for the SAE A P2 DOT 14 and would be what you'd need.

view full answer...

Will Grease Cap Plug Part RG04-010 Fit Tie Down Engineering SuperLube Grease Caps

Product Page this Question was Asked From

Continue Researching